Question about Cars & Trucks

1 Answer

How to rebuild the cap due to taking apart and forgot where the small spring and ballbearing goes thanks

Posted by on

  • roy longstaff
    roy longstaff Apr 08, 2015

    thanks for your email with regards question about fuel cap rebuild a friend of my brother,s had one on a dented tank so i now have been able to use that one would like to thank everyone who looked at my question

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,805 Answers

What cap did you try to fix
basically if there is a ball and spring ,then the ball goes in first to seal off on the seat and is regulated by the spring which goes in last.

Posted on Apr 08, 2015

  • roy longstaff
    roy longstaff Apr 13, 2015

    Thanks Bill For Your Help It Was For A Suzuki GSX1400 petrol tank cap

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rebuild dw708


I assume you are asking about the Dewalt
DW708 TYPE 3 Crosscut Miter Sawas seen here
http://www.ereplacementparts.com/dewalt-dw708-type-crosscut-miter-saw-parts-c-1009_1163_2604.html

Have you taken it apart yet? You will need screwdrivers, spring clip pliers, small bearing puller and a pipe same diameter as the inside of the bearing; for replacement of bearing.
Be sure to take out the brushes before taking out the armature.
Part 165-90
You most likely will have to replace part 87 too.
The bearing rests in there and gets worn too.
Serious bearing/vibration problems causes the end cap part 84, to wear out.

Jan 23, 2012 | Cars & Trucks

1 Answer

I have a dodge 4x4 1500 the trans temp light comes as well as the over drive off light when vehicle is at an idle i then lose overdrive. vehicle is only at an idle for 2 or 3 min. havent even started to...


There is a check valve in the transmission cooling lines on these trucks. This valve is in the line near the radiator on the passenger side. This valve can get stuck and cause the Trans to overheat due to no trans cooler flow. When these Transmission get hot overdrive goes out. Located this valve take the line apart near it and use a small screwdriver and try to free it up. It is spring loaded and should push in and spring out easily. If you can't you must replace it. Don't drive it like that or you could ruin the transmission

Nov 07, 2010 | 1999 Dodge Ram

2 Answers

How do u change cv boots on 4 wheel drive front axle


okay this can get tricky there are several ways to do this. How i do it I disconect the lower ball join you will need a pry bar to get the lower aframe apart i then take the hub assembly apart if locking hubs. if full time four wheal drive there is a cap at the center of the hub remove cap and take carter pin out remove nut, if has hubs like i said take hub assembly apart may need a tool looks like a big socket remove nut pull rotar assembl off and to the side ussually will swing to the front of the vehicle look at the back of the shaft if goes streight into transfer case should pull right out it may have a plate with several small bolts remove bolts should fall right out. to enstall reverse proceedure. I recommend having a haynes or chiltons manual so you know what the parts look like and what goes where.

Oct 31, 2010 | Suzuki XL7 Cars & Trucks

1 Answer

1989 toyota camry 232000miles Runs rough at idle


YOUR problem is the carby acc pump and idle jet ...... what you need to do is remove airfilter and take the top off the carby and you should see a small ball and spring under gasket ...when you open the throttle it will pump petrol to the small pick up jet and the other jet will take over ...clean out carby jets and rebuild and that should be ok

Sep 23, 2009 | 1989 Toyota Camry

1 Answer

Need diagram for rear brake spring assembly on a 1994 toyota tercel


The bottom spring should be hooked into a small hole on thefront shoe bottom, and to the adjuster cam on the other(rear) shoe. The remaing two spring are one long and one short. The shorter spring goes from the front shoe to the post and the longer spring goes from the rear shoe to the post. Just a suggestion, when you are dissasembling anything complex like this, it's a good idea to take a few digital pix along the way. Good luck my friend,Dana P.S. if you haven't taken the other side apart yet you can use it for a reference only mirror the assembly.

Sep 06, 2009 | 1994 Toyota Tercel

1 Answer

We took a two barrel carburetor apart and now we can't find where a spring goes its a 84 buick regal


Go here and click on pictures if you need a close up,The rebuild section is near the bottom. You can also look here

Aug 03, 2009 | 1984 Buick Regal

1 Answer

2003 Hyundai Accent clutch slave cylinder problem


dear friend-the spring and valve came from the back where the bolt goes in . it is a compensating valve.you put it back valve first then spring or you can leave it out.it makes no differense

Jul 02, 2009 | 2003 Hyundai Accent

1 Answer

Engine rough idle cold. passes smog once temp reaches thermostat


you can take apart the top section and blow out the small passage that's bellow the throttle plate.

May 01, 2009 | 1987 Toyota Tercel Liftback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...