Question about 2003 Mini Cooper

1 Answer

POWER STEERING PUMP REPLACEMENT

DOES THE SUBFRAME HAVE TO BE DROPPED TO REPLACE THE PUMP?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Mini Master
  • 531 Answers

Posted on Apr 01, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering pump 2007 Ford Edge located where? Can't seem to locate it..need to replace it; 3.5 engine


CAUTION: While repairing the power steering system, care should be taken to prevent the entry of contaminants or premature failure of the power steering components may result.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02 .
  1. Using a suitable suction device, siphon the power steering fluid from the power steering fluid reservoir.
  1. Remove the RH inner fender splash shield. For additional information, refer to Section 501-02 .
  1. Using the special tool, disengage the power steering pump belt from the power steering pump pulley and position it aside.
    • Install the removal tool between the belt and the pulley and turn the crankshaft bolt clockwise to disengage the belt.
  1. Remove the 4 bolts and position the driveshaft aside.
  1. Using a suitable jack, support the rear of the subframe.
  1. Remove the 2 nuts, 4 bolts and the subframe support brackets.
  1. Remove the 2 middle subframe nuts.
  1. Lower the rear of the subframe.
  1. Release the clamp and disconnect the power steering supply hose from the power steering pump.
  1. Disconnect the power steering pressure (PSP) switch electrical connector.
  1. Remove the power steering pressure line fitting banjo bolt and disconnect the line from the power steering pump.
    • Discard the 2 seals.
  1. Remove the 3 power steering pump bolts and the power steering pump. This is a job best left to a qualified repair shop !

Jul 26, 2016 | 2007 Ford Edge

1 Answer

How do I tighten a steering fluid pump that has come loose?


John, If you mean loose off engine and bracketing, the links show complete replacement, you do not need all the steps, it shows what bolts are being tighten to secure pumps.
press the helpful button

How to Install the Power Steering Pump AutoZone Car Care

How to replace your power steering pump

How to replace power steering pump

Replacing Bad Power Steering Pump

Feb 08, 2016 | Cars & Trucks

1 Answer

Video of replacing power steering pump 2000 Pontiac montanspa


Pontiac Grand Am/ Olds Alero 3.4 liter powersteering pump ...

? 16:26
https://www.youtube.com/watch?v=fhOaJUAgPTA
Jan 6, 2014 - Uploaded by JoeTheAutoGuy
this is a video on how to replace a power-steering pump on the Gm 3.4 ... My 2000 Olds Alero (2.4) power steering pump itself is fine, but the ...

How to Replace Power Steering Pump GM 3800 - YouTube

? 19:45
https://www.youtube.com/watch?v=-T8Kek90qAA
Sep 28, 2014 - Uploaded by Rich Rodgers
How to replace the power steering put on General Motor 3800 Engine. ... Sign in to add this video to a playlist. ... Power Steering Pump Pulley Removal and Installation ACDelco - Duration: 6:25. by MyPartsGarage 136,263 views ... How to replace a power steering rack and pinion on a 2005 Pontiac Grand ...

How to Install the Power Steering Pump - AutoZone Car ...

? 6:27
https://www.youtube.com/watch?v=PMX-dBhgwlo
Apr 19, 2012 - Uploaded by AutoZone
How to Install the Power Steering Pump - AutoZone Car Care ...Power Steering Pump Replacement 2000-2006 Chevrolet Tahoe, Suburban, ...

How to replace your power steering pump - YouTube






Dec 28, 2015 | Pontiac Cars & Trucks

1 Answer

How do you replace the steering rack on my 2001 Ford Windstar??


YOU HAVE TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE YOU HAVE VECHICLE PARKED ON LEVEL SOLID GROUND.ONCE VECHICLE RAISED.REMOVE FRONT WHEELS.REMOVE TIE RODS END COTTER PINS AND CASTLE NUTS.REMOVE TIE ROD ENDS FROM THE KNUCKLES.REMOVE FRONT STABILIZER BAR.POSITION THE DASH OPENING WEATHER SEAL FOR THE STEERING COLUMN OUT OF THE WAY.REMOVE OR DISCONNECT THE FOLLOWING.REMOVE PINCH BOLT RETAINING THE STEERING COLUMN INTERMEDIATE SHAFT COUPLING.REMOVE STEERING GEAR RETAINING NUTS BOLTS.REMOVE REAR SUBFRAME BOLTS.USE WIRE TO SUPPORT EXHAUST COMPONENTS UNLESS YOU ARE REMOVING THEM COMPLETELY.SUPPORT THE EXHAUST SYSTEM FLEX TUBE AND REMOVE THE FLEX TUBE TO DUAL CONVERTER Y PIPE ATTACHMENT.LOWER THE VECHICLE SLIGHTLY UNTIL THE REAR SUBFRAME SEPARATES FROM THE BODY APPROXIMATELY 4 INCHES.REMOVE THE HEAT SHIELD BAND AND FOLD THE HEAT SHIELD DOWN.ROTATE THE RACK AND PINION ASSEMBLY TO CLEAR THE BOLTS FROM THE FRONT SUBFRAME AND PULL TOWARD THE DRIVERS SIDE OF THE VECHICLE.PLACE A DRAIN PAN UNDER THE VECHICLE AND DISCONNECT THE POWER STEERING LINES.REMOVE THE RACK AND PINION ASSEMBLY THROUGH THE DRIVERS SIDE OF THE VECHICLE***** TO INSTALL ****** INSTALL NEW TEFLON O - RINGS ON THE POWER STEERING LINE FITTINGS. PLACE THE RACK AND PINION RETAINING BOLTS IN THE GEAR HOUSING.INSTALL RACK AND PINION ASSEMBLY THROUGH THE DRIVERS SIDE OF THE VECHICLE.INSTALL POWER STEERING LINES ON THE RACK AND PINION ASSEMBLY. INSTALL RACK AND PINION ASSEMBLY ON THE SUBFRAME.INSTALL ******** HEAT SHIELD.INSTALL TIE ROD ENDS TO THE KNUCKLES TIGHTEN THE CASTLE NUTS AND INSTALL THE COTTER PINS.INSTALL STABILIZER BAR.INSTALL RACK AND PINION ASSEMBLY RETAINING BOLTS.TORQUE THEM TO 85 - 99 FT LBS. RAISE VECHICLE UNTIL SUBFRAME CONTACTS THE BODY.INSTALL REAR SUBFRAME RETAINING BOLTS TORQUE THEM TO 83 - 112 FT LBS.INSTALL EXHAUST SYSTEM FLEX TUBE TO DUAL CONVERTER Y PIPE.INSTALL FRONT WHEELS.INSTALL A NEW PINCH BOLT IN THE STEERING COLUMN INTERMEDIATE SHAFT COUPLING ON THE RACK INPUT SHAFT TORQUE PINCH BOLT TO 25 - 33 FT LBS.POSITION THE STEERING COLUMN OPENING WEATHER SEAL OVER THE STEERING GEAR HOUSING.LOWER THE VECHICLE FILL THE POWER STEERING FLUID RESERVOIR. START THE VECHICLE AND CHECK FOR LEAKS. CHECK FOR PROPER WHEEL ALIGNMENT AND STEERING WHEEL POSITION.BLEED POWER STEERING SYSTEM.

Oct 14, 2010 | 2001 Ford Windstar

2 Answers

How to replace power steering pump


2004 Pontiac Grand Prix V6-3.8L VIN 2

Power Steering Pump: Service and Repair
Power Steering Pump Replacement
NOTE: The content of this article / image reflects the changes called out by TSB: 05-02-32-004.

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg

Sep 07, 2009 | 2004 Pontiac Grand Prix

1 Answer

Replacing power steering rack


subframe must be dropped

Aug 14, 2009 | 2003 Kia Sedona

1 Answer

Steering Rack boot replacement


In my opinion, removing the front subframe makes this job much easier.

Jack up and suitably support the front of the car so it is in a wheels free state.
With wheels removed;

  • Remove the anti-roll bar drop links from the anti-roll bar
  • Free off the lower arm ball joints off
  • Remove the track rod ends from the swivel hubs
  • Remove the nut and bolt and special clip on the lower steering column universal joint
  • loosen off and disconnect the feed and return pipes to the power ram (beware stinking power steering fluid pouring everywhere!)
Steering and suspension wise, the subframe should be free!



  • Remove the nut and bolt that secures the lower engine mounting to its bracket (the bolt that goes through the big round rubber mount at the back of the engine)
  • Disconnect all relevant gear linkage rods (this will be clear when you are under there!)
  • Support the subframe with a jack or somesuch and free off the 6, 18mm bolts that secure the subframe to the body shell.
  • remove all subframe mounting bolts.
  • lower the jack that is supporting the subframe, it should all drop quite nicely and then get stuck on the steering column universal joint! A good old college shove frees this and then you should be able to remove your subframe assembly from under the car.

Jul 30, 2009 | 1997 Mitsubishi Diamante

1 Answer

Cant remove power steering rack


The racks are a bit tough on these cars since theyre on the subframe. a lot of extensions and a swivel will help it come off the subframe but hate to break it to you : you will need to drop the entire subframe to pull off the steering rack. The subframe holds the motor and suspension. Its odd though that you need to remove the rack. Perhaps the rack isnt an issue. Can you post up what your issue is?

Jun 23, 2009 | 2005 Honda Accord

2 Answers

How to change inner tie rod ends?


if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------
  • The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
  • If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
  • If the leak is not corrected, replace the fitting seals.
-------------------------------------------------------------
f12ee38.gif
-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal
  1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
  1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
  1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal
  1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .


    13b4d70.gif

  1. Support vehicle with jackstands under front jack pads.
  1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
  1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
  1. Disconnect heated oxygen and catalyst monitor sensors.
  1. Support flex pipe.
  1. Remove bolts and disconnect flex pipe from the converter.
  1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
  1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
  1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
  1. Remove rear subframe-to-body retaining bolts.
  1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
  1. Remove heat shield band and fold shield down.
  1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
  1. Place a drain pan under vehicle and remove line fittings.
  1. Remove power rack and pinion steering gear through LH wheel well.
  1. Remove and discard the O-rings.
Installation
  1. Install new Teflon® O-rings on line fittings as outlined.
  1. Place steering gear retaining bolts in steering gear housing.
  1. Install power rack and pinion steering gear through LH wheel well.
  1. Install power steering line fittings to power rack and pinion steering gear.
  1. Position power rack and pinion steering gear into front subframe.
  1. Install ******** heat shield.
  1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
  1. Install LH front stabilizer bar. Refer to Section 04-01 .
  1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
  1. Raise hoist until rear subframe contacts body.
  1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
  1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
  1. Connect heated oxygen and catalyst monitor sensors.
  1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
  1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
  1. Remove jackstands and lower vehicle.
  1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
  1. Check system for leaks and proper operation.

Apr 15, 2009 | 1997 Ford Windstar

Not finding what you are looking for?
2003 Mini Cooper Logo

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mini Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mini Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...