Question about 2007 Chrysler Pacifica FWD New Cars

2 Answers

Whgat all needs removed to change starter - 2007 Chrysler Pacifica FWD New Cars

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Chrysler Master
  • 531 Answers



check the ground wire first before replacing...

another youtuber says to remove the exhaust manifold to have easier access to the starter

"Remove the front exhaust manifold and remove the starter from the top.Pull the front exhast manifold and dipstick remove the 3 bolts with a 15mm socket or wrench pull the starter from the top"

Posted on Apr 01, 2015

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 2,963 Answers

I recommend a repair manual, you will probably want it next time. But how do you know you have a bad starter? could be something else. Could be battery, battery terminals or corrosion, wiring to the starter solenoid relays or ignition switch for the starting.

Posted on Apr 01, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change starter 2005 chevy van express


first disconnect batt positive. jack vehicle up on passenger side. you can see starter at rear of engine. you may have to remove plastic around bellhousing to remove starter. There are two bolts holding starter in place.usually 15 mm socket. there is a small nut holding wire. 5/16 or 11/32 socket.. remove it. large nut usually 13mm socket. once removed just reverse procedure. leave comment if successful.

Mar 21, 2010 | 1999 Chevrolet C2500

1 Answer

How do i change the starter on my 89 nissan truck?


FIRST OF ALL YOU NEED TO REMOVE NEGATIVE BATTERY CABLE.SAFELY RAISE SUPPORT TRUCK ON JACK STANDS.THEN YOU REMOVE ELECTRICAL CONNECTORS FROM STARTER BE SURE TO TAKE NOTE OF LOCATION OF WIRES CONNECTORS ON STARTER.THEN YOU REMOVE STARTER BOLTS THEN STARTER.WHEN PUT IN NEW STARTER TORQUE BOLTS TO 29 - 36 FT LBS.

Mar 10, 2010 | 1989 Nissan Hardbody King

2 Answers

96 cadillac eldorodos starter is positioned in a place i cant figure how to change it. anyone know the method.


You will need to remove the intake and all components atatched to be able to change the starter.If you do not have good shop expirence or a mechanical backround I do not suggest you change it.Sorry but it is in a difficult place and a lot of critical items will need to be removed.

Feb 17, 2010 | 1996 Cadillac Eldorado

2 Answers

Step by step instructions to change starter/94 Lexus LS400


Disconnect the battery.
Disconnect the wires from the starter.
Unbolt & remove the starter.
Bolt the new starter into place.
Connect the wires to the starter.
Connect the battery cables.

Dec 30, 2009 | 1994 Lexus LS 400

1 Answer

I need to know how to chang the starter and know and located


4.3 litre V6 ? first disconnect the battery before you start, then raise vehicle and place safely on approved weight rated jack stands, you will need a 14 mm or 15 mm socket wrench and an 8 mm socket or wrench to remove wire leads from starter and solenoid, remove starter by removing the two mounting bolts, reinstall in opposite form. starter is on paasenger side of motor sitting in the driver seat...

Sep 24, 2009 | 1999 GMC Jimmy

1 Answer

I need help changing my starter i need to know how to drop the engine so i can get to the starter


Here are instructions as well as links to some helpful diagrams.

This starter motor removal procedure is time consuming. An alternate method of removing the starter would be to remove the engine fan(s) and radiator, then remove the starter motor from the top of the engine. If you chose to go this route, radiator and fan removal can be found in Section 3 of this manual.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. If equipped with A/C, perform the following:
    1. Use a floor or jack stand to securely support the engine and transaxle assembly so they will not rotate.
    2. Remove the front engine mount bolt from the insulator and front crossmember mounting bracket.
    3. Carefully lower the front of the engine, rotating the engine forward allowing more space for easier access to the starter. For easier removal, do not remove the wiring from the starter at this time.
    4. Remove the 2 starter motor-to-transmission housing mounting bolts.
    5. Remove the starter and solenoid assembly from the transmission housing. Position the starter accordingly for access to the wiring.
    6. Remove the positive battery cable nut and remove the positive battery and alternator output wire from the starter. The wiring is shown in the accompanying figure.
    7. Detach the push-on solenoid connector. Pull back on the slide and push down on the rear tab to release the lock.
    8. Position the starter vertically so the pinion end faces downward, then remove the starter motor through the bottom of the vehicle. It may be necessary to move the A/C lines aside slightly to maneuver the starter out of the vehicle.
http://www.chiltonlibrary.com/content/images/8971/images/89712g29.gif

http://www.chiltonlibrary.com/content/images/8971/images/89712g30.gif

http://www.chiltonlibrary.com/content/images/8971/images/89712g31.gif

I hope you found this information useful. Best of luck on your repair.
Greg

May 29, 2009 | 1997 Dodge Neon

1 Answer

I need to change my starter on a 1991 mercury sable


Starter are one of the easier mechanical engine parts to change.

1) DISCONNECT THE BATTERY.
2) Disconnect the electrical cable running to the solenoid on the starter.
3) Remove the two bolts holding the starter in place.
4) Pull the starter out.

To install another starter, do the above steps in reverse order in reverse.

Apr 04, 2009 | 1991 Mercury Sable

1 Answer

94 toyota carolla starter clicks eventualy starts


You have two options: replace the starter (easiest, but most expensive), or replace the contacts (cheaper, but more work involved).
In any case, you have to remove the starter. Disconnect the battery BEFORE you start. Locate the starter and remove the wires going to it. The starter is held onto the transmission with 2 large bolts. Remove both, and slide the starter out.

If you want to change the contacts, observe the starter, locate a metal plate held on with 3 bolts. Remove the bolts and the plate. You will now see a plunger, and 2 copper colored contacts. Those are what needs to be replaced. Changing the contacts is easy, just do one at a time, and ensure that all insulators are installed properly on reassembly.

Jan 13, 2009 | 1994 Toyota Corolla

1 Answer

Changing the starter on a 2003 Taurus


you need to remove it from the bottom front of car . disconnect the negative battery cable. remove the front splash shield from under front of car , working from under car take the protective cap off the wires that go to starter and then disconnect all wires from starter marking each one for propper reinstalation, remove the bolts holding starter and remove from under vehicle. replace in reverse order.

Nov 22, 2008 | 2003 Ford Taurus

1 Answer

Changing a starter


its not to hard to change disconnect battery .remove nut on front of starter to support bracket . remove 2 bolts going through starter into block. lower starter . disconnect wires on solonoid . remeber where they go. tools you will need 10mm 13mm 15mm sockets

Oct 22, 2008 | 1995 GMC Sierra

Not finding what you are looking for?
2007 Chrysler Pacifica FWD New Cars Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...