Question about 2005 Nissan Quest

Open Question

2005 nissan quest shifts solenoid not working Brake light working

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4369 Answers

SOURCE: 1999 nissan quest brake pad replacement

Remove wheel & tire,
remove 2 torx bolts that go from the inside to the outside of the vehicle. They are on the inner side of the brake caliper.
lift the caliper out of the rotor.
remove the brake pads.
To install, you must first squeeze the caliper piston back inot its bore. Do this slowly to prevent damage to the piston. You are forcing excess brake fluid back into the master cylinder reservoir. Slow constant pressure will get the job done. Use a large c clamp or a wooden hammer handel if that's all you have.
Fit the new brake pads in the calipers and slide the assembly back over the rotor.
install the 2 torx bolts, size 40? head I think.
You are done.
If rotors are scored bad, replace them too.

Posted on Jan 21, 2009

  • 30 Answers

SOURCE: replace control panel on 2004 nissan quest

there is a c-clip you need a small screwdriver to pull it out then gearshift knob will pull off

Posted on Jan 28, 2009

  • 4369 Answers

SOURCE: 2001 brake pad replacement 2001 nissan quest

The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal

  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Posted on Apr 24, 2009

TwinTurboZ
  • 78 Answers

SOURCE: Wont shift out of park unless I stick a screw driver in a small hole above gear shifter.

You must remove the console yes, and you need to replace the shift lock solenoid.

Posted on May 15, 2009

  • 14 Answers

SOURCE: vdc light and brake lights comes ON.

does the master cylinder have enough brake fluid in it, low fluid level commonly causes those two lights to come on you may wanna check your brake fluid level.

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why can't ignition key be removed?


Sounds like the solenoid mounted on the shifter. You have to replace the shifter to replace the solenoid. I would check the resistance of the solenoid. Usually 30 to 40 ohms. check the plug to it(Corrrosion) and the resistance of the wires from the brake switch to the solenoid(5 ohms or less). Those shifters are cheap. Could be the brake switch also. Next time it doesn't work, See if the brake lights come on.

Apr 11, 2016 | 2006 Nissan Quest

1 Answer

WHY IA MY 2005 NISSAN ALTIMA WILL NOT SHIFT FROM PARK?


The most common culprit for this failure is that the interlock release solenoid has failed, either because it is jammed or because your brake light circuit has failed. (Do I need to mention that your foot must be on the brake in order to take the vehicle out of Park?)

First, check your Owner's Manual to determine how to bypass the interlock so that you can move the vehicle (if you need to move it).

Next, verify that your brake lights are working. If they are not, replace the fuse for that circuit. If they are still not working, replace the brake light switch.

Next, remove the cover from the PRNDL and check the condition of the interlock solenoid. Make sure it is receiving voltage when the brake is applied. Replace as necessary.

May 14, 2014 | 2005 Nissan Altima 2.5

1 Answer

Lights dont work but brake lights do


No.
Brake lights are wired through the ign. key.

Apr 18, 2014 | 2005 Nissan Quest

1 Answer

Shift locked in park/2000 nissan xterra se


check battery volts should be 12.5 volts,if yes check see if you have rear brake lights.if no replace brake light fuse.if brake light fuse okay a faulty brake light switch or shift lock solenoid not working,when you apply brake the electrical circuit goes to shift lock solnoid so you can get transmission out of park.shift solenoid located centerconsole located near gear position indicator.

Sep 01, 2012 | Nissan Cars & Trucks

1 Answer

2005 Nissan Quest ABS, TCS, Brake, SLIP, Service Engine Soon lights are on and speedometer and odometer are not working


Retrieve codes from the ECM and report it is possible that the codes are related and could be something like speed sensor of some sort.

Jun 25, 2012 | 2005 Nissan Quest

1 Answer

2005 chevy impala wont shift from park


I would begin by checking the brake lights to see if they are working. Find a piece of wood to wedge between the seat and brake pedal or have a assistant get in the vehicle and depress the brake pedal while you observe the lights to see if they are functioning. If the brake lights work then the issue is with the shift interlock solenoid or the wiring to the solenoid. If the brake lights do not illuminate then I would go to the owners manual to check for the fuse location and test the fuse.

Apr 06, 2012 | 2005 Chevrolet Impala LS

1 Answer

The shifter is locked and engine turns on but can not shift from park


1st, have someone step on brake pedal while you check to see if your brake lights are working, if yes proceed to step 2, if not check your brake light fuse(Left side of dash fuse#20- 10amp)IF fuse is good replace brake light switch on brake pedal. 2nd Step (brake lights ok) Turn key on engine off, press and release brake pedal several times slowly, listen for a click and and pulse on shifter handle. IF yes you have a shifter malfunction replace shifter assembly. IF no, inspect shift interlock solenoid and or relace solenoid and cable. You should see a small access cover about the size of a peanut around base faceplate of shifter assembly use small screwdriver and remove cover, use screw driver to press button underneath plate and release shifter into reverse and drive gears(this is manual overide) if you need to move vehicle in the meantime.

May 16, 2011 | 2005 Nissan Altima

1 Answer

Brake lights don't work, already replaced bulbs.


1) check fuse
2) replace brake lights
3) check brake pedel switch

Nov 09, 2010 | 2005 Nissan Quest

1 Answer

Vdc light and brake lights comes ON.


does the master cylinder have enough brake fluid in it, low fluid level commonly causes those two lights to come on you may wanna check your brake fluid level.

Oct 07, 2009 | 2005 Nissan Quest

1 Answer

Wont shift out of park unless I stick a screw driver in a small hole above gear shifter.


You must remove the console yes, and you need to replace the shift lock solenoid.

May 11, 2009 | 2005 Nissan Altima

Not finding what you are looking for?
2005 Nissan Quest Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...