Question about 2004 Isuzu Rodeo

1 Answer

Have had a new clutch fitted now the 4x4 want engage

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Isuzu Master
  • 3,519 Answers

Hi Kevin:
When they replaced the clutch, they may have removed the transmission and disconnected the shift linkages. When it was re-assembled, I would suspect that one of the linkage components was not re-connected correctly. If the work was done in a shop I would recommend having a friendly chat with the owner/manager about resolving the problem. Odds are they should be very good about it. If you and some buddies did it in the back yard, it's back on the jacks and check the linkages.
Work Safe!!! Chock it and block it. Don't need to drop it!

Posted on Apr 01, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2008 VW Passat 1.9 TDI Diesel - Clutch problem

bring back and have shop adjust the clutch

Jul 27, 2017 | Cars & Trucks

1 Answer

Instruction for fitting new clutch 1995 mitsubshi Pajero 4x4

lots of work ahead transfer case drive shafts gearbox out

you will need the repair manual ... 1996 will cover the job
Mitsubishi Pajero Workshop Owners Manual Free Download

fit a new flywheel if it cant be machined
all dual clutches must have the flywheel replaced

Oct 27, 2016 | Cars & Trucks

1 Answer

1995 Toyota Tacoma 3.4L 5-speed manual feels like 4x4 is not fully engaging.

check that the clutch is fully engaging by checking if there is free play at the throw out lever and clutch push rod . If you cannot push the rod back into the cylinder then the slipping is because the clutch is only partially engaged. Replace the clutch master cylinder if that is the case. If it is right then the fault will be in the pressure plat/ cutch plate and it may require a clutch kit.

Feb 05, 2014 | Cars & Trucks

1 Answer

My 2008 Nissan titan will not engage in 4x4 high but will engage 4x4 low. There is also a grinding noise when I try 4x4 on the fly. The light comes on and say it is engaged but it doesn't really engage....

There may be a problem with the syncro rings in the 4x4 high section of the box. It may have something to do with you driving technique by not allowing the synchro rings a chance to bring the mating gear up to speed. When the change is required it should be done at a relative low speed wit either a brake in the accelerator pedal ( lifting the foot for a second) or a clutch disengagement (pushing the clutch in and out for a second). This breaks the load on the gear teeth and allows for the change to be completed

Dec 22, 2013 | Nissan Titan Cars & Trucks

1 Answer

97 4runner has 4x4 problem engaging

-Sound like need new clutch.


Apr 08, 2013 | Cars & Trucks

1 Answer

94 Chevy 2500 Clutch Engagement?

You probably have a hydraulic clutch. A hydraulic clutch has both a master and a slave cylinder. The slave cylinder engages/disengages the clutch plate. You might be low on clutch fluid in the master cylinder, or the system may need to bled similar to bleeding brakes. Worst case is you need a new clutch, pressure plate, and throwout bearing. They should all be replaced when doing a clutch job.

Aug 23, 2012 | Cars & Trucks

1 Answer

F250 4x4 2002 4x4 does not engage bought new component that goes above glove box need wiring diagram

Try depressing the clutch and the brake pedal at the same time while moving the dial to 4x4?

Nov 30, 2009 | 2002 Ford F250 Super Duty SuperCab

2 Answers

1997 Toyota Tacoma v6/4x4/manual: Clutch petal/Clutch

I currently have a 1998 Toyota Tacoma, and the clutch pedal does not return all the way. I know it is not the clutch, it is actually the spring located underneath the pedal. It is catching and not releasing after pushed.... Hope it helps.

Jun 19, 2009 | 1998 Toyota Tacoma

3 Answers

Ford Fiesta 1.25 Zetec - Gears not engaging so no drive power

Sounds like your clutch cable is caught. Try new cable.

May 19, 2009 | 2000 Ford Escort

1 Answer

I have a 1992 chevrolet c1500 4x4 5.7 litre -when you first start it up,with ac on,ac compressor clutch will engage,disengage 3 times then will not engage,if i run 12 volts to the clutch pressure switch...

The pressure switch will open when freon pressure is too low, the compressor clutch is controlled by the computer or module.
The switch isn't necessarily bad, you can check it with a multimeter. The fitting it is threaded onto should have a valve inside and an O ring to seal so no freon loss should happen when removed.

Aug 21, 2008 | 1992 Chevrolet C1500

Not finding what you are looking for?
2004 Isuzu Rodeo Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14380 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides