Question about 2005 Kia Picanto 1.1

Open Question

Why the speed 5 no function - 2005 Kia Picanto 1.1

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

High cruising rpm


no year, no real help.
mike cruises at 90 mpy (Dallas new speed limit 85 on one road)
larry at 75
me 45. so>>>
but doing it backwards works way better
what is speed at 3000 RPM , a common speed.
answer in my 96 goes 59 mph. in 5th gear.

the rpm is a function of what tranny and tire size.
here are all listed
The G16 is no V8 it spins fast and last 300k miles. if serviced.
see this table for 3000 rpm speeds.
there are 5 speeds possible in top gear.
what transmission tell you which it is , there are 3 trans. and 2 engines. each are Unique.

http://www.fixkick.com/part-time-test.html#SPEED

chart one is stock. tires.
chart 2 is big tires.
the equation is there so you can do yours, from any RPM you want.

May 21, 2014 | Geo Tracker Cars & Trucks

1 Answer

1997 Toyota 4runner manual transmission - Just had clutch replaced - will not downshift into 1st gear unless car is going less than 5 mph -


that simply means your clutch is no longer slipping and its functioning properly first is for taking off so if you are still rolling second is the go to your brakes do the work of stopping you under 5 miles per hour no need to down shift at that speed

Nov 01, 2013 | Cars & Trucks

1 Answer

Where is the speed sensor located on 1996 mitsubishi rs 2.0 non turbo


There is actuly 3 of them one on each front wheel that sence the speed that the wheels are turning . And one on the transmission tail stock that sences the speed the transmission is turning . The vehicle control module compares information and corrects brake and engine functions as well as shift functions . The most likely ones are the front wheel ones that are giveing you problems because they get water and road salt witch tends to corroad the the connecters to them . That would be ware to start looking for problems . Keep im mind that all of these sensors generate voltage there little generators that create what is called a refferance voltage of about .5 volts DC and be tested by spinning the wheels and haveing a volt meter hooked to the output wires from the connectors

Jul 19, 2011 | 1996 Mitsubishi Eclipse

1 Answer

AC WILL NOT TURN ON WILL RUN BY USING SCAN TOOL


{: ) When an A/C mode is selected, the A/C control head or the A/C programmer supplies a 12 volt signal to the PCM A/C request input. The A/C compressor clutch relay is controlled by the PCM. The PCM provides a ground path for the A/C relay coil. When the A/C compressor relay is engaged battery voltage is supplied to the compressor clutch coil. The PCM will enable the A/C compressor clutch whenever the engine is running and the A/C has been requested unless one or more of the following conditions are present:
Throttle angle greater than 90 %.
• A/C head pressure greater than 414 psi (4.27 volts) or less than 34 psi (0.35 volt) (as determined by the A/C refrigerant pressure sensor). • Ignition 1 voltage below 10.5 volts. • Engine speed greater than 4500 RPM for longer than 5 seconds. • Engine speed greater then 5400 RPM for any amount of time. • ECT greater than 125°C (257°F). • IAT less than 5°C (41°F). • Throttle angle is greater than 90%. • A/C head pressure is greater than 414 psi (4.27 volts) or less than 34 psi (0.35 volt) (as determined by the A/C refrigerant pressure sensor). • Ignition 1 voltage is below 10.5 volts. • Engine speed is greater than 4500 RPM for longer than 5 seconds. • Engine speed is greater then 5400 RPM for any amount of time. • ECT is greater than 125°C (257°F). • IAT is less than 5°C (41°F). Any of the conditions described above will inhibit A/C compressor relay operation.

A scan tool can control a/c operation without regards to the prevailing parameters that can inhibit its functions. Remember that the scan tool is a very effective diagnostic tool.
In this case, the scan tool was able to control a/c, which is an indication that the PCM is communicating, and that circuit 459 going to the relay and then to the a/c compressor are normally functional. You need to check now if the sensor input signals are within the specified ranges.

Jul 06, 2011 | 1997 Chevrolet Venture

1 Answer

Pontiac montana 2000 general fan (all air-hot and cold) doesnt function changed the fuse and now only works from settings 3-5 and change the heater relay is my fuse labelled 'air" not the right...


there is a blower motor resister which controls fan speed i believe its located pass side of dash by blower motor has one plug about 5 wires red ,orange .blue yellow

Feb 09, 2011 | 2001 Pontiac Montana

2 Answers

02 suburban heat/ac fan


Burnt relay or coil, listen for-and follow the clicking when you change fan speeds it'll lead you to your relays. Also look for burnt connectors.

Jun 29, 2008 | Chevrolet Suburban 1500 Cars & Trucks

Not finding what you are looking for?
2005 Kia Picanto 1.1 Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...