Question about 2005 Kia Sedona

1 Answer

How to remove idler pulley for a kia sedona 2005

Posted by on

  • arobinson22 Apr 14, 2015

    Hi Carlos Rivers, I want to help you with your question, but I need more information from you. Can you please add details in the comment box?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Kia Master
  • 10,875 Answers

Unbolt the bolt next to it

Posted on Apr 14, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: how to remove 94 lesabre idler pulley

remove belt then there is a bolt in center of bracket remove that bolt it is a 15mm bolt

Posted on Jan 01, 2009

  • 8 Answers

SOURCE: Can not find radiator drain plug on 2005 Kia Sedona

http://www.fixya.com/

Posted on May 20, 2009

  • 1 Answer

SOURCE: change idler pulley

It's a T-40 size, but I removed the bolt by first removing the bracket holding the pulley--I assume you're talking about the alternator idler pulley, the one right below the alternator. The bracket is held in place by three 14 mm bolts which I was able to reach from the top of the engine (after removing the black plastic air tube). I then put the bracket in a vise and "buzzed" off the 14 mm nut using an electric impact wrench ($30 +/- from Heartland of America). Be careful when putting the nut back on--the impact wrench will likely be too much torque!


Posted on Jun 23, 2009

  • 157 Answers

SOURCE: Where is the input speed sensor on KIA sedona 2005

on transmission has 2 wires at right side of trans .by axel

Posted on Nov 24, 2009

  • 77 Answers

SOURCE: how to remove the rear bumper on a 2005 Kia Sedona

1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. bs6d007a.gif 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. bs6d007d.gif B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. bs6d007e.gif D. Remove two screws from side of bumper assembly. bs6d007b.gif E. Remove four bumper mounting bolts from under of vehicle. bs6d007c.gif 3. Install rear bumper in reverse order of removal.

Posted on Jan 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil pump location 2005 kia Sedona 3.5 eng


Oil pump is on the front of the motor in behind the crank pulley. The oil pump cover must be removed to access. 5-6 hrs labor

Apr 11, 2015 | 2005 Kia Sedona LX

1 Answer

How can i remove timing belt on 2005 kia sedona



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes

May 08, 2012 | 2005 Kia Sedona LX

1 Answer

How do you replace a serpentine belt on a 2005 3.5 liter Kia Sedona


Click on the following free, direct Link. It has the Serpentine Belt Diagrams you will need.

http://www.2carpros.com/car_repair_information/year/2005/make/kia/model/sedona/2005_kia_sedona_drive_belt_routing_diagram.htm

On the Serpentine Belt: Scroll down the Link Page to Diagram G00323207, it shows the Tensioner.
1. Loosen the Pulley Lock Nut - identified as "A"
2. Loosen the Adjustment Bolt - identified as "B"
3. The Tensioner Pulley should move up and slightly to the left, loosening the belt enough to remove.

Installation is the reverse of the above.
Note on Diagram G00323206 the deflection tolerance at the 22 lbs pressure on the belt.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!



Apr 10, 2010 | 2005 Kia Sedona

1 Answer

How to ajust belt that goes around alt. 2002 kia sedona


The idler pulley has a nut in the middle of it. You loosen that, then there is a tensioner bolt at about 4 o'clock, turning that will move the idler pulley away from the belt.

Dec 30, 2009 | 2002 Kia Sedona

1 Answer

Need location of inner belt tensioner for '05 Kia Sedona


It is below the power steering pump pulley, there is a nut in the middle of the pulley that you loosen and then loosen the tensioner bolt to move the pulley away from the belt.

Nov 04, 2009 | 2005 Kia Sedona

1 Answer

How do change the serpentine belt on a 2005 Kia


There is a tensioner pulley that has a nut in the middle of it, loosen that nut and there is a tensioner bolt that when you loosen it, it slides the pulley away from the belt to replace it.

Sep 27, 2009 | 2005 Kia Sedona

1 Answer

How To change idler Pully on 2000 Kia sadona Van


There is a nut in the middle of the pulley. Remove that nut and slide the pulley off the shaft.

May 30, 2009 | 2003 Kia Sedona

2 Answers

Change idler pulley


It's a T-40 size, but I removed the bolt by first removing the bracket holding the pulley--I assume you're talking about the alternator idler pulley, the one right below the alternator. The bracket is held in place by three 14 mm bolts which I was able to reach from the top of the engine (after removing the black plastic air tube). I then put the bracket in a vise and "buzzed" off the 14 mm nut using an electric impact wrench ($30 +/- from Heartland of America). Be careful when putting the nut back on--the impact wrench will likely be too much torque!


May 17, 2009 | 2003 Kia Sedona

1 Answer

How do I change the unibelt on my 2002 Kia Sedona?


The tensioner pulley has a nut in the center of it that you loosen, then behind the pulley is a tensioner bolt that when you turn it, it moves the pulley away from the belt in a slot on the tensioner bracket.

Mar 28, 2009 | 2002 Kia Sedona

Not finding what you are looking for?
2005 Kia Sedona Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...