Question about 2007 Toyota Sequoia

Open Question

I have a broken rt frt wheel lug. is there more to it than just taking off the rotor to get to the stud?

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: need to replace broken lug bolt

If you have room behind the broken lug you can usually drive it out with a good smack of a sledge hammer. To re-install, use a stack of washers between the nut and flange and draw the lug into position. (plenty of oil on threads to avoid galling)

Posted on Apr 19, 2009

  • 770 Answers

SOURCE: 89 4x4 pu broken wheel stud

Will have to remove LR drum, The stud should drive out fairly easily, as a precaution, apply penetrating oil and let soak prior to driving it out. Install the new stud..about a $4 item, (compared to $100 to get one fixed at the toyota store, then put your wheel back on, snug up all lugs then torque to 83 ft/lbs.

Posted on Jun 19, 2009

  • 41 Answers

SOURCE: Broken front lug nut studs

remove tire and then disc. Drive broken stud out the back. Get a manual just to be sure. I havve done this on my Camry without to much trouble. To install just drive in with hammer from rear.

Posted on Aug 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Saturn vue


Are you saying that you are trying to replace the lug stud? The studs are pressed into the spindle that the rotor is mounted to. It is possible to pull the stud thru the spindle by tightening the lug nut, but this is not the proper way to do it. The proper way would be to remove the rotor and the spindle from the vehicle and press the lug stud into the spindle with a press. But I have pulled studs into the spindle when I was broken down on the side of the road with 5 broken studs. You just have to make sure you tighten the nuts until they do not tighten anymore, and check the nuts every day until they do not tighten anymore.

Sep 01, 2014 | Saturn Vue Cars & Trucks

2 Answers

Need help to change front wheel stud on 1999 honda civic EX


1. first take the wheel off so you can see the the caliper and the rotor. make sure the car is on stands and not just waving around on a jack.
2. look behind the caliper and use your finger to locate, a pair of bolts behind the caliper... they will be holding the caliper into place on the suface of the rotor, by a simple look and feel you can see these, they should take a 17mm socket undo them and remove the bolts. at this stage you should see the the caliper become loose.
3. remove the caliper by pulling it up and away from the rotor
4. now you can see the rotor remove this it will simply slide away.
5. this will leave the hub exposed and the studs.. you will see that they are wedged into the hub
6. remove the stud/s by hitting them / it with a hammer be carful to not damage the other studs if you just replacing one.
7. there is one spot where the will be a gap and you will be able to get the stud in behind the hub and have a little bit of room, rotate the hub to there, make sure the car is out of gear or this will be very difficult :)
8 once the stud is in take something you can use as a spacer like a larger then the stud nut. for example and then put one of the wheel nuts on and tighten slightly
9. use a hammer and drive the back of the stud home, and slowly tighten the wheel nut as you go.
10. once this is done your finished put all the bits back togeather in the oppersite order and replace the wheel.






source:http://wiki.answers.com/Q/How_do_you_replace_front_wheel_stud_from_a_1999_honda_civic

Jul 30, 2008 | Honda Civic Cars & Trucks

1 Answer

Jeep broken lug nut stud


Causes are the mounting surface of the the rotor or drum not clean when wheel was installed, wheel bent, suspension damaged, wheels not torques down correctly or left loose.

Apr 09, 2012 | 2007 Jeep Grand Cherokee

1 Answer

How do I replace a broken lug nut out of 98 windstar?


you don`t say if its front or rear lug nut(assuming you mean stud).remove the wheel and then the drum or rotor,then take a hammer and hit the broken stud to remove it from the hub assembly.with the correct wheel stud insert it through the hole and make sure its in straight,install the wheel nut and tighten the nut to pull the stud into the hub until all the way in.you may have to install washer on the stud and re-install the nut and tighten until the stud is seated all the way.

Sep 16, 2011 | 1998 Ford Windstar

1 Answer

How to replace broken stud of honda crv 2001 front wheel


remove wheel, brake assembly & rotor. rotate to where the broken stud is in the opening where the brake assembly was. drive the broken stud out of the hub flange. then install the new stud by stacking washers on the new stud and tighten the lug till it pulls the new studs flange tight against the back side of the hub. remove lug and washers , reassemble .

May 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

I need to know what are the bolts are called that the lug nuts go on a vehicle? I thought that it was the rotor. Mine has stripped.


You require "lug studs" to be able to install a lug nut to secure the tire.

You will need a special tool to press the lug studs in and out of the flange, or you can follow these directions;

First you will have to pound the broken lug stud(s) out of the wheel hub, use a punch or a drift that is a little smaller in diameter than the lug stud, and be sure that you do not pound on the flange itself, then you will need a lug nut and about a half an inch thick of flat washers.

1. Insert the new lug stud through the wheel hub from behind so that the threaded end is facing out towards you and then put some grease on the threads.

2. Then slip the flat washers onto the lug stud followed by the lug nut, and run the lug nut down backwards with the flat end of the lug nut towards the flat washers to take up the slack and use plenty of grease on the threads.

3. Then using a breaker bar tighten the lug nut until it pulls the lug stud through the wheel hub and it is flush with the wheel hub.

Be sure that the amount of flat washers used will make up for any non-threaded part of the lug stud that might stick out past the wheel hub preventing the lug nut from pulling the lug stud all the way through the wheel hub, and basically you do not want the lug nut to run out of threads before it can pull the lug stud flush with the wheel hub.

Let me know if you require any further assistance.

Jul 30, 2010 | 1999 Mazda Millenia

2 Answers

I have a broken wheel stud on left wheel of a two-wheel drive 2002 Envoy. How do I replace it?


TAKE VECHICLE TO SEARS AUTO CENTER OR ANY TIRE WHEELS BRAKE ALIGNMENT SHOP THEY CAN PRESS OUT THE STUD WITH OUT DAMAGING WHEEL BEARING.AND PRESS YOU IN A NEW LUG NUT STUD.PROBABLY CHARGE YOU $25.00 DOLLARS.

Jun 12, 2010 | Cars & Trucks

3 Answers

Broken stud on wheel


The studs press out and in. Perhaps a hammer would work. Replacements studs can be purchased. Need to remove hub, of course.

Aug 13, 2009 | Hyundai Motor 2003 Elantra

1 Answer

How to replace front broken wheel stud on a '02 jeep grand limited 4x4...steps involve to replace the bolt with a new one? thanks!


Remove wheel, brake caliper and rotor. Give the broken lug a good shot with a decent weight hammer and drive it out of the hub flange. Put new stud into hole, place a stack of washers on it and place the lug nut on backwards (flat side in)
Use oil on the threads to prevent binding, tighten lug 'till stud is seated, replace everything you removed.

Aug 11, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Had rotors and pads replaced, now pulsing in brakes and squeaking from right rear. pulled wheels and found rotor holes for lugs not hte same diameter as lugs, and no screw holes or anything to attach...


not knowing where you had this done and parts replaced I, I would take it back, sound like they didn't cut the rotors correctly.....as for the screw hole depends on what brand of rotors they put on???(factory or aftermkt.??) ...still it shouldn't VIB. you can check yourself IF it's the frt or back by applying the PARK brake and see if it VIB.....if so it's the rear if not more likely the FRT....hope this helps you...GL

Jul 09, 2009 | 2004 Ford Windstar

Not finding what you are looking for?
2007 Toyota Sequoia Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...