Question about Mazda 626

1 Answer

How you get to back nuts on a mazda 626 v 6 - 626 Mazda Cars & Trucks

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,602 Answers

They make a special tool for that job. i know that sound nut but they do. some foreign auto parts store maybe able to help, i use to be bap import parts, look up foreignautoparts, city and state, zip.

look into it, it maybe dealer tool
you could look and ask the local auto part store, tool shack, sears tools may have it tool truck also have it.

Posted on Mar 31, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the nuts on a torque converter on a 2001 mazda 626 with a 2.0 ltr engine


Hi Bradley:
I`ve always just used a six point socket, flex bar, and handle extension combined with brute force.

Jul 12, 2016 | Mazda Cars & Trucks

1 Answer

How to change the starter in a 1999 Mazda 626 4 cyl?


It's quite easy, firstly disconnect the battery then you won't get any little suppresses lol, then it's a matter of removing the nuts or bolts on the starter and remove it, then just do everything in reverse and all should be good, hope this helps

May 03, 2014 | 1998 Mazda 626

1 Answer

How do i bleed the clutch on a 1997 mazda 626


get a friend to help you. locate the little bleeder nut near where the line goes into the transmission. use correct wrench to loosen it make sure your clutch reservoir is full with dot3 brake fluid. after your friend pushed down on the clutch pedal open the little nut then close it. do this till not air bubbles come out and refill the reservoir

Jan 23, 2011 | 1996 Mazda 626

2 Answers

My daughter's 1998 Mazda 626 needs minor work on back wheel wells. To better get to the rust, I need to remove the back wheel, I've jacked up the car, removed the wheel nuts on the back tire, but the...


with the car safely supported try kicking the tire off. You can also try a large hammer swinging from behind the tire. You can also try putting the lug nuts on loosely and driving the car back and froth until the wheel falls off.

Dec 01, 2010 | 1998 Mazda 626

1 Answer

How to remove rear hub on a 1996 mazda 626 4 cylender car


what do you want the rear hub removed for is the hub bearing gone/worn.ther is a small dust cap in the middle of the wheel remove with the help of a screwdriver you will see a large nut this nut to unlock turn anticlockwise when nut is removed the a little gentile tap from the back should remove the hub.adrian,,,,,,,,,

Aug 14, 2010 | Mazda 626 Cars & Trucks

1 Answer

I can't loosen the left front wheel bearing nut on my 1991 Mazda 626. I have tried a lot of extra torquing on the wrench, and have tried heating the nut with a plumbers propane torch, but it won's budge.


It should be a left-hand thread. Have you tried reversing your wrench direction? This should loosen it.

I trust that you had taken the cotter pin out of the castle nut.

Oct 08, 2009 | 1991 Mazda 626

1 Answer

1995 mazda 626 glx speedometer and mileage counter not working. Rev counter works though. Does it have a cable problem or sensory


Not to sure, but i think its cable. Loosen the nut that holds the cable to the speedo drive on the gearbox. check if the inner cable is broken.

Regards
Phillip

Sep 18, 2009 | 1995 Mazda 626

1 Answer

How do I replace the front wheel bearings on a Mazda 626 1998


The front bearings on a mazda 626 are sealed and you must remove the entire hub assembly to have a shop or dealer install the bearings. The hardest part is you need to remove the center axel nut and it is very tight and is called a stake nut. If you do not have a fairly good amout of skill at repairs, this is one job that is safest left to the pros. Just one missed step can create more damage than you could beleive.

May 20, 2009 | 1998 Mazda 626

2 Answers

Changing the tail light bulbs on a 2000 mazda 626


The Tail Lights Are Accessed From The Inside Of The Trunk There Will Either Be A Panel Immediately Behind Where The Light Is Or Carpet. Remove It And It Will Give You Access To The Rear Of The Bolts Just Grab Twist And Pull And The Light Will Come Out.

Jan 26, 2009 | 2000 Mazda 626

1 Answer

1990 626 Mazda rear drum brakes


This "large nut" you are talking about is holding a drum. Usually over him is a cover. Use big screwdriver and hammer to remove cover, gently strike from all sides, and when you remove it you will approach to a big nut. Pay attention that under the drum is a whole breaks sistem. After you remove the nut gently strike from the rear, from all sides (left, right, up and down). Drum will fall off.

Sep 28, 2008 | 1990 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...