Question about 2007 Ford Explorer Eddie Bauer

Open Question

Power running boards won't come out and makes a noise

Running boards noise when opening door

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Battery is dead and ticking noise is coming from under the hood.


have you recharged battery ? and are there any codes coming up on OBD ? possible it's a power relay (ticking),when you open door your lowering power needed for interior lights .

Sep 01, 2014 | 2001 Toyota Camry

1 Answer

The gas cap won't pop open.. makes a noise.. i am almost out of gas


There is no other release. Take it to a mechanic or the dealer. Or else just force the door open to reach the cap. Is it just a door cover or the fuel cap itself?

Jul 02, 2013 | 2000 Volkswagen Golf

1 Answer

My lights won't turn off in my car when I lock it and there's also no honking noise. Then a few minutes later the alarm will go off. If I leave it unlocked the alarm doesn't go off but the...


its the door switches they are sticking and telling the car door is open. open and close both doors a few times and make sure they are closed good and try again to make sure it is setting properly you will know cause the care dome light will go and it will emit a short honk when activated!! =) mine just did the same thing

Oct 11, 2011 | 2006 Saturn ION

1 Answer

The passenger door power window won' t go up or down . Makes a brief noise but wont move any more. 2 door coupe


The cable in the window mechanism (regulator) has broken and wrapped up around the gear on the motor. You will need to replace the regulator/motor assembly.

Aug 19, 2011 | 1999 Pontiac Grand Prix

1 Answer

My power sliding door doesn't open fully. It makes clicking sound and a somewhat of a jerking motion. It open or closes slighty but the entire it makes the above mentioned noises. Any help would be...


I'm not sure about the noise, but the jerking motion might be because your the center roller (located in the rear middle of the sliding door) has worn out and need to be replace. This is a will known problem.

Your problem is very hard to answer because 05-10 odyssey has so many problem with sliding door.

rear latch:
-door not to latch close
-door not to work

front latch:
-door not to open

lock actuator:
-door not to open
-door will pop when opening

window motor:
-window not to work
-door will only open half way

center roller:
-jerking motion when opening
-door kick back close while opening
-door kick back open while closing

Door motor:
-door not to work
-cause door to jam

good luck

Dec 17, 2010 | 2005 Honda Odyssey

2 Answers

Running board stopped working


More than likely you accidentally disabled the feature if you have already checked the fuses and they are good.
Your owners manual tells you how to re-enable the power deploying running boards .
I'll paste a copy of the directions for you :
***********copy***********

Enable/disable:
To enable/disable the power running board feature, refer to the Message
center in this chapter.
• When this feature is disabled <OFF>, the running boards will move to
the stowed position regardless of the position of the doors.
• When this feature is enabled <AUTO>, the running boards will move
back to the correct positions based off of the door positions.

(Message Center )

Setup menu
Press this control for the following
displays:
• Reset to English (if in another
language)
• System Check
• Oil Life
• Units (English/Metric)
• Autolamp Delay (if equipped)
• Easy/Entry Exit
• Air Suspension (if equipped)
• Autolock (if equipped)
• Power Liftgate (if equipped)
• Power Deployable Running Boards (if equipped)
• Compass Zone (if equipped)
• Compass Calibration (if equipped)
• Language


Power Deployable Running Boards (if equipped)
This feature automatically deploys the side running boards for easy
entry/exit from the vehicle or for cleaning.
1. To disable/enable the power
running board feature with the
vehicle in P (Park), select this
function from the SETUP control for
the current display mode.
2. Press the RESET control to select the running boards setting as
follows:
• AUTO: the running boards will automatically deploy when a door is
opened and automatically retract when the door is closed,
• OUT: the running boards will remain deployed regardless of the doors
being open/closed. This setting can be used when washing the vehicle, or
accessing the roof rack. The running boards will stow and enter AUTO
mode when the vehicle speed exceeds 5 mph ( kph),
• OFF: the running boards will remain IN regardless of the doors being
open/closed.

Let me know how this turns out.



Benjamin

Jul 23, 2009 | 2003 Lincoln Navigator

2 Answers

My 2004 Pontiac Vibe making a continous clicking sound.


Check the hose connected to the drain for the condensor. It's behind the passenger side carpet on the floor by the firewall. (pull the carpet back from the top. Then you will see the black rubber hose on the bottom) It just gets pushed back on. Passengers kick it off some times. The noise drove me NUTS till I found it. It makes a hissing noise while running, then a tin can noise when under power/acceleration.

Hope this helps!

Jul 19, 2009 | 2004 Pontiac Vibe

1 Answer

Door will not slide automatically; emits loud beeping noise


Something similar to that was happening with our Odyssey...the beeping when you are driving whether it's ongoing or intermittent is the "safety alarm" letting you know the door is not closed. The power lock is not engaging. What I do when I get the beeping while driving is hit the Door Close button. It causes the door to attempt to engage again. To fix it...we first cleaned out the space below the side running board (kids were hiding crayons and things in there), then looked for any obstructions along the top and bottom tracks. I sprayed a lubricant along the tracks (I'd suggest the dry lube kind...I used WD40 the 1st time and had streaks of it dripping down after driving), use a lube that has a long straw to spray in small places...and spray up into the track that runs the length of the middle of the car. Manually open and shut it a few times to get the tracks lubed, then try it out.
If you press the open OR close button by remote or in the car and get nothing...no movement/no noises/no beeping...then it could be the electrical circuit itself, the signal itself may be impeded...or the motor shot. Have you tried any of these suggestions before?

Mar 16, 2009 | 2000 Honda Odyssey

1 Answer

Open door tone???


Are both doors closing tightly? Perhaps one is just loose enough for it to send signal that it's open. Even try sitting still with vehicle running and open one door at a time, and push lever of button that trips it, in with your thumb, to see if it stops. if you come across one that doesn't do it instantly, or it goes on /off with slightest movement, you probably found the culprit. Let's try the free/cheap/obvious things first.

Feb 08, 2009 | 2003 Jeep Wrangler

2 Answers

Noise inside doors


hello friend, may their is noise generated due to friction, it generally happens when vehical get old, if urs is not old one, just out in a local service garage, I am sure you will able to fix it with ease.

have a nice day.

Jun 09, 2008 | 1997 Honda Accord

Not finding what you are looking for?
2007 Ford Explorer Eddie Bauer Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...