Question about Nissan Pickup

1 Answer

Went to get in my 1986 Nissan pickup truck the clutch will not even push down. it will not press to the floor its like there's something stuck in between the clutch

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 257 Answers

Sounds like your pilot bearing on the clutch slave cylinder

Posted on Apr 13, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
drshenk
  • 9 Answers

SOURCE: 1988 Nissan Pickup Clutch problem?

The fork in the tranmission could have got stuck and there is also two bleeds on that system you have to bleed the one on the tranmision first then the one on the master cylinder. It could posible a clutch problem but not really sounding that way.

Posted on Dec 04, 2008

  • 22 Answers

SOURCE: nissan clutch problem

If your not able to shift into any gear that means your clutch is not engage/disengaging. Check for fluid leaks, you said topped off and fluid levels were low? It sounds like you have a Slave cylinder or master cylinder leak, if its leaking its bet to replace both.

Posted on Apr 27, 2009

  • 599 Answers

SOURCE: removing the 8o amp main fuse from 1986 Toyota pickup

yes, you must remove the top panel on the fuse block the 80 amp fuse is bolted to the the fuse panel, hope this helps if not get back to me as i strive to be the best please rate my fix Thanks Ray

Posted on Apr 29, 2009

  • 2 Answers

SOURCE: clutch pedal went to the floor but did not come

there is a plastic clip that connects the clutch pedal to the rod that goes to the master cylinder, chances are that it let go. Bad thing is that it is only available from GM along with the rod. It is around 50

Posted on Oct 24, 2009

  • 44 Answers

SOURCE: 1989 Nissan Hardbody pickup V6

your too high in the gears when you are trying to climb a hill.

Posted on Feb 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The clutch on my 1986 nissan pickup engages at the very top of the pedal. How do i adjust it


I have A 91 Nissan pickup with a hydro clutch and I adjusted it by threading out the threaded rod at the top of the clutch peddle inside the cab I hope that helps

Sep 16, 2012 | Nissan Cars & Trucks

1 Answer

Clutch does not slip but when clutch pedal is pressed down does not let clutch release. how much travel should the slave cylinder have and is there any adjustments i can try.


Since your clutch is operated by hydraulic pressure, there is no adjustment. If pushing in the clutch pedal doesn't release the clutch, then the most common cause is either air in the system or the master or slave has failed. If the clutch is the original factory one then it is possible that the clutch itself has worn.

Jul 17, 2011 | 1986 Nissan Pickup 4WD 1986

1 Answer

The clutch peddle went to the floor when i pushed the clutch peddle in


Check the floor by the clutch peddle if it is wet (you may need to look at the very top of the peddle)than you problem is the clutch mastercylinder

Jan 31, 2011 | 1994 Nissan Pickup

1 Answer

1987 nissan pickup- clutch worked fine one day, next time the pedal went almost to the floor with no resistance, I had about 1" distance from the floor to disengage the clutch. checked the master cylinder...


sounds like your clutch master cylinder or slave is no good. do your self a favor and replace them both if you are going to be replacing them.

Sep 21, 2010 | 1987 Nissan Pickup

1 Answer

Clutch paddle releases overnight but stays to the floor while driving.


I would guess that the throw-out bearing is sticking. Doesn't this truck have a hydraulic clutch?How old is the clutch Asm.?

May 15, 2010 | 1986 Nissan Pickup 4WD 1986

1 Answer

1986 Nissan Pickup


Shift fork may also be one of the reason! watch the shift fork while moving the clutch in and out.
1)The shift fork is near the clutch master cylinder on the tranmission housing. you should now move the fork left and right while the clutch is moved in and out. 2)From your query, it sounds to me that your clutch is not engaging and disengaging completely. 3) This is due to the air block. Make a bleeding process to blow the air out! 4)A broken shift fork will also prohibit the clutch from engaging/disengaging.

May 10, 2010 | 1986 Nissan Pickup 4WD 1986

1 Answer

Clutch pedal stuck up


You have to replace the Slave Cyl. when you put on the new one you have to bleed it ..To get the air out of the new line.

Mar 10, 2010 | Hyundai Motor 2002 Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...