Question about Cars & Trucks

1 Answer

Codes p 300 and 302 has been tough to get it read bc won't stay on hut a few daysand then q uit

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 10,875 Answers

These codes indicate a multiple misfire (P0300) and a misfire on cylinders #1 and #3. This can normally indicate and issue with jumped timing or a possible vacuum leak. May also indicate a faulty ignition coil and wire.

2001 AUDI TT 1.8

Posted on Mar 31, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2005 buick terraza cxl starting disabled

Get the codes read to find the area of the faults causing limp mode

Sep 07, 2017 | Buick Cars & Trucks

1 Answer

What causes my 1998 ford escort to hesitate about moving forward hut then will pick up and go on?

You may have air bypassing the MAF sensor (mass airflow sensor). Pull the ribbed air intake hose to the engine and bend it around and check for cracks, they crack on the bottom, if none are found you most likely have an issue with the MAF sensor. You should also have the fault codes read with a OBD2 fault code reader or have the test done by a local auto parts store like Autozone, it is free.

Mar 16, 2017 | 1998 Ford Escort

1 Answer

How do i get my check engine light to turn off on 94 towncar

If it is staying ON, you should better get the codes read. If you have already done that, you can reset the codes by disconnecting the negative battery terminal for few minutes and then plugging it back.

May 20, 2013 | Cars & Trucks

1 Answer

The car strs up and huts off

Can you ask the Question again??? As I am reading this, it makes no sense....NOW, NOW,NOW ???

Apr 08, 2013 | 1988 Chevrolet Beretta

1 Answer

Car engine won't stay running

Have the fault codes read Look for a throttle position sensor or idle speed sensor fault.

Apr 05, 2013 | Cars & Trucks

1 Answer

2007toyota service engine light

You need to have the engine computer scanned with an OBD II code reader.
If the light is on the computer has detected a problem with it's engine or emission controls. As long as the light stays on, the problem is ongoing. You won't know what it is until you get the diagnostic trouble codes retrieved form the computer's memory. Then a technician or someone here may help you solve it.
Autozone and a few other parts stores will read your codes for free.

Nov 16, 2011 | 2007 Toyota Camry

1 Answer

Please help me. I have an 04 jeep liberty sport 3.7l with 76000 miles and a constant engine light on. When started the idle jumps around too 1.5 to 2 rpms and stay high. While driving the engine will rev...

Did they give you the error codes, or just tell you that it was the multiple engine misfire, evap and TPS? If they didn't give you the codes then I would take it to an autoparts store and have them read the exact codes. Replacing the heads because the valves are sticky is questionable in my opinion. Dealerships sometimes are quite unreasonable when it comes to replacement parts. Plus they seem more apt to take advantage of a KNG (Know Nothing Girl) than most shops.

I would like more information about the engine combustion cleaning that they performed!

You might also want to go to the and post it there. They have multiple Jeep specialists that might be able to steer you in the right direction.

Jul 02, 2011 | 2004 Jeep Liberty

3 Answers

Car will start but won't stay running

Is the Check Engine Light on/ If yes, go to AUtozne & get codes read and report them here.

Also, try cleaning the MAF sensor and throttle bdy with spray carb cleaner.

Check for 40 psi of fuel pump pressure. Can you hear pump hum for 5 seconds when key is turned to ON? Listen at tank at rea of car, pump is in the tank.

May 15, 2011 | 1996 Ford Taurus

1 Answer

1997 Grand Jeep Cherokee Limited 5.2 V8: Probleem: De computer doet het niet, geeft zwart beeld. Kan je de computer aan en uit zetten? Is er een zekering kapot? Alvast bedankt.

Turn the key on three times with out hitting the starter and leave it on the last time the dash display will tel you the codes and you canget an idea of what's wrong. sorry I only read and write English ( american) so I can only guess this is that you want. Good luck!

Sep 16, 2010 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides