Question about 2004 Cadillac SRX
Posted by Anonymous on
No sir, on the ly7 HFV6 3.6l in the 04-09 srx and cts the knock sensors are located on the sides of the engine block. Bank 1 and two are visible fringe wheel well. Not to hard to get to with a 3/8 drive 13mm socket, universal joint, and short extension. I would also check the connector with a multi meter while doing this job to ensure you have a good connection and harness is not damaged. Best of luck!
Posted on Jan 27, 2017
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.
Posted on Jan 25, 2009
If you go to the auto parts store they should have a fuel line disconnect tool that has a 5/16ths end an a 3/8ths end. The tool is shaped like an X. Before you start you need to pull the fuel pump fuse under the front of the REAR passenger side seat while the car is running and let it stall. it will release the built up pressure. This is important unless you want gas to spray every where. Then take the tool and start with the end of the filter with two lines. Place the appropriate end of the tool over the smallest inlet, push the tool in then pull the line towards the filter and then push the line away and it should disconnect. Do the same with line above. Then you can use the two appropriate size wrenches to disconnect the outlet end. reconnecting the new filter is simple just make sure your quick connect lines click in all the way and you tighten the outlet line well, I think its like 22 or 25 ft/lbs.
Posted on Dec 15, 2009
Under intake manifold on top of block,you need to remove intake to access sensors there are two of them you can't miss them when intake is off. After replacing sensors you need a new intake gasket.
Posted on Apr 04, 2010
The knock sensor is located under the intake manifold.The starter is also located under the intake manifold.Hope this helps.Good luck.
Posted on Jul 21, 2010
Testimonial: "it was helpful informations,appreciate that."
Tips for a great answer:
Mar 04, 2015 | 2006 Cadillac SRX
Aug 28, 2014 | 2004 Cadillac SRX
Nov 08, 2012 | 2005 Cadillac SRX
Sep 04, 2011 | 2006 Cadillac SRX
Aug 17, 2010 | 2004 Cadillac SRX
Aug 11, 2010 | 2005 Cadillac SRX
Dec 25, 2009 | 2004 Cadillac SRX
Jun 16, 2009 | 2004 Nissan Frontier
Apr 30, 2009 | 2004 Cadillac SRX
254 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: