Question about Cars & Trucks

1 Answer

MY WATER PUMP PULLY RATTLESIN IDEL WHEN IGIVE ITGAS

NO LEAKS STEERING VERY WELL JUST A CLICKINGAT THE PUMP PULLY

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 42,159 Answers

Replace the water pump as the bearing is failing

Posted on Mar 31, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Olds 307 Belt Diagram


307's have a unusual routing, it's easy to get confused.

From back to front:
1) Crank - Water Pump - Air Conditioning
2) Crank - Power Steering - Water Pump
3) There are two versions, depending on how many grooves the power steering pump has:
(1-groove P/S):Water Pump - Alternator
(2-groove P/S):Crank - Power steering - Alternator - Water pump
4) Crank - Air Pump

May 14, 2012 | Cars & Trucks

1 Answer

Well, do i remove the power steering pump or pull the pully to remove the water pump and if the pump, is access from underneath ??


you have to remove your power steering pump to replace your water pump you remove one bolt from the top and one from underneth by going threw holes in power steering pump pully

Sep 17, 2011 | 1995 Oldsmobile 88

1 Answer

Where is the watter pump located on a 94 mercury sable? How do i take it off to replace it?


this is for a 3.8 v6. first Disconnect the battery. then take off the Radiator cap and set it aside. on driver side at the bottom of the Radiator. there a twist valve. this is the coolant drain. put a large container under drain then open the valve. once it stops. on the passenger side towards the back in front of the belt tensioner but under the altenator is the water pump. but to get to it you have to take off the mounting bolts for the altenator (LEAVE ALL WIRES CONNECTED this will save time) now set it aside. now loosen the 4 bolts on the water pump pully. now take the drive belt off. take a pully puller and take the pully off the power steering. there should be a metal support going from the back of the a/c compresser to the water pump. undo the 2 bolts hold the bracket on the a/c compressor.(on a side note do not loose any of the bolts cause ford dont carry them anymore and hardware stores dont have them. only place i found is a junkyard) detach the hoses on the water pump. (Caution there will be some coolant left have container ready)l
now loosen the bolts on water pump. now under the car near the front right there are to engine mounts LOOSEN THEM ONLY ENOUGH TO RAISE THE ENGINE ENOUGH TO CLEAR. using a jack. raise only the passenger side of the engine enough for the water pump to clear the wheel well. once that is done undo the bolts on the water pump pully and take off and pull off the water pump and take off the support bracket and pull off the water pump. clean off leftover residue on the engine black. now put the silicon gel/paste on both sides of the new gasket. use a decent amount but not too much. then wipe off edges. and put the water pump back as shown below.


tar171_0.gif
attach the hoses. now put the support bracket back on then tighten the bolts down only a little and let the silicon set overnight for best leak protection. (by doing this. it allows the sillicon to create a good strong seal) after it set overnight tighten down the bolts. put the water pump pully back on put on the bolts hand tight . lower the jack SLOWLY! now retorque the enigine mounts to 70lbs i believe. put the 2 bolts for the a/c compressor back in. put the power steering pully back on. (MAKE sure you aline the pully up with the others or it will throw the belt) rebolt on the altenator. put the belt back on and refil the cooling system with coolant. reconnect the battery. start the engine for 30 sec then turn off check for leaks and top off coolant then then fill the rezivor to proper level. restart engine and run till operating temp then check for leaks

Nov 23, 2010 | 1994 Mercury Sable

3 Answers

I'am replacing water pump 2006 grand prix,all bolts are remove but one. I can't remove it because theres a wheel pully in the way. I think it's the power steering pump help.


You may have to remove the pump...
BUT , maybe not...
The pump pully has holes in it... with the power steering belt loose or off ... turn the pully to see if the holes will allign with the bolt you are trying to remove... if not... then the power steering pump must be removed to gain access to the last bolt..

Sep 26, 2010 | Pontiac Grand Prix Cars & Trucks

1 Answer

When water hits belt - it throws it off!


check all the bearing in all of the acc. power steering pump water pump idler pully a/c compressor etc. if all good no nise and they spinn freely check the alinment of all the puilly mak so they all line on together. sometimes the power steering pully get worn inside the pump and allow it to move back and forth too much some play is normal. also the power steering pully trys to walk off the shaft and make the belt track off the other pullys .

Jul 01, 2010 | 1994 Plymouth Grand Voyager

1 Answer

How to remove pully to the left of the water pump 98 pont .3.8 .trying remove last bolt onthe left but pully is in the way


If I remember correctly, that should be the pulley for the power steering pump, You're going to need to remove the power steering pump to get to it.

Nov 20, 2009 | 1998 Pontiac Bonneville

1 Answer

Power steering working OK slight squek in pully and pully vibrati


HI, these signs will confirm a pump structure failure and i would recommend replacing this power steering pump.

Apr 09, 2009 | 1994 Toyota 4Runner

2 Answers

On 98 intrigue water pump removal how do i clear the ps pully


Im not sure what engine you have since this information was not provided. But the Power Steering Pump pulley usually has some 'holes' on the pulley in which you can get a wrench through to loosen and remove the bolt.

Dec 29, 2008 | 1998 Oldsmobile Intrigue

1 Answer

Serpentine Belt Diagram


water pump pully to crank pully

Aug 21, 2008 | 1989 Dodge Ramcharger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...