Question about 2007 Ford Edge SEL
Posted by Anonymous on
If you handy remove an O2 sensor closer to the engine and start the vehicle if the cat is clogged this will allow the pressure to come out and run
Posted on Mar 30, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
your egr valve might be faulty bring it in to the auto parts to have it check out what your looking for is the 32 code on the OBD II scanner.
Posted on Sep 04, 2009
SOURCE: 2007 Ford Taurus
After doing some research on this subject and that trouble code, signs point to the fuel pressure regulator. I believe this is located inside the fuel tank on the taurus. I believe you have a "returnless" fuel system. Meaning there is only one line coming from the tank with no return line. The pressure regulator in the tank can fail causing fuel pressures to go sky high. That will cause fueling issues which can stall the car or cause it to run badly.
Based on the information you provided, I think this is the best place to start. Good luck.
Posted on Dec 02, 2009
it sound like a ABS-sensor is sticking are its bad give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.
Posted on Jan 12, 2010
First off, if you're attempting this, I'm assuming you're someone mechanically inclined or at least somewhat of a grease monkey -
NO NEED for me to tell you how to change the first THREE spark plugs that stare at you when you pop-up your hood - These should be child play for you... if not, take your car to a shop and stop reading... (no offense)...
The back ones are the fun ones to get to!
Keep in mind you will need to move a lot of the wire harnesses around - you may have to cut a few tie-down clips or zip-ties to help you out.
1 - Remove the Air Box - Remove Air Filter - No need to dismantle the whole Unit into pieces... Loosen up the clip clamp at the Throttle Body and pull out the whole Unit -
** Disconnect the Sensors, Disconnect the Front Rubber Hose and the little valve underneath **
2 - Loosen and remove the screws that hold down the manifold (6 total I think in the front) - There is a super long one all by itself in the middle - the others are at the edges
** Also, take your time to detach the Wire Harness/Hoses strapped to the Manifold (in the front) you can do this by removing the black electrical tape and replacing later when you're done ...
3 - There is one screw under the Throttle Body - remove it - it's kinda' hidden but you'll see it.
4 - There is another one on top of the manifold towards the back - it's hidden under the hood cowl
** Look on top of your engine towards the back - Locate two rubber hoses attached to the manifold - FYI - You will be working in a very TIGHT spot, but be patient and make sure you don't give up! **
5 - Loosen/Detach Rubber Hose on the Left (Pass Side) attached to the Manifold (PCV Valve?) - Make sure you don't drop it - it connects the manifold to the Engine - it's a small "L-shaped" hose
** There is a tiny connector right below that valve, you cannot see it but you can feel it, it's easy to remove, just unplug it - AGAIN, it's a tight spot, but not impossible to work with. **
6 - Loosen/Detach another Rubber Hose on the Right (Driver Side) and your manifold is ready to come off - Move it around, and pull it out... careful with the wire harnesses around and the other hoses that are sitting on top of the engine.
Make sure you Disconnect the Mass Air Flow Sensor and Air Temperature Sensors!!!
Once you pull out the Manifold - it is easy as cakes to replace your three other Spark Plugs -
Follow the steps backwards and VOILA! - It is a LOT easier to do then all this jargon I've written
Posted on Jan 30, 2011
Tips for a great answer:
Jun 06, 2017 | 2007 Ford Fusion I4 SEL Sedan
Apr 13, 2011 | 2007 Ford Edge SEL Plus
May 11, 2017 | 2007 Ford Edge SEL Plus
Mar 06, 2010 | 2007 Ford Edge SEL Plus
Sep 24, 2009 | 2007 Ford Edge SEL Plus
Aug 29, 2009 | 2007 Ford Edge SEL Plus
Aug 12, 2009 | 2007 Ford Edge SEL Plus
Jun 16, 2009 | 2007 Ford Edge SEL Plus
34 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: