Question about 2002 Chevrolet Tracker

Open Question

How do I replace left front axle seal on a '02 tracker? has bolt on axle,so can't get to seal due to inner axle,do I need to take apart the diff?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 24 Answers

SOURCE: left front axle seal

This is a fairly involved job. You will have to remove the brake assy, then seperate the ball joint and remove the axle assy. You will need a seal puller to remove the axle seal (At trans I assume) and a seal driver or something flat to install the seal. You will also need a 32mm socket ( if my memory is correct ) for the axle nut and a torx or hex socket for the brake caliper and a splitting fork for the balljoint. Be sure to tourque the axle nut to spec when reinstalling or you will be replacing a wheel bearing next. Hope this helps...Good Luck.

Posted on Feb 05, 2009

Ad
  • 20 Answers

SOURCE: how to replace a right rear axle seal in a 2001

you must remove all brake parts then you get to the axle easy to do with the right tools

Posted on Jul 22, 2009

  • 4 Answers

SOURCE: 2002 chevy Tracker front differential seal is leaking

Probly broken axel,seal or linkage.

Posted on Dec 03, 2009

  • 14036 Answers

SOURCE: how to remove rear axle to replace axle seal?

YOU NEED A HAYNES OR CHILTON REPAIR MANUAL.TO REMOVE REAR AXLE YOU HAVE TO REMOVE REAR DIFFERENTIAL COVER AND GASKET.YOUR DIFFERENTIAL HAS EITHER PINION SHAFT LOCKING SCREWS OR C - LOCKS.THEY HAVE TO REMOVED BEFORE AXLE SHAFT WILL COME OUT.

Posted on Mar 04, 2010

  • 36 Answers

SOURCE: How to remove and replace a passanger front axle

THIS AXEL IS THE SHORT ONE,ABS SYSTEM,START OUT REMOVING THE CALIPER AND PADS,ALL BOLTS ARE METRIC,REMOVE THE AXLE BOLT FIRST,THEN,REMOVE THE TIE ROD BOLT,THEN REMOVE THE UPPER CONTROL ARM BOLT,THE SPINDLE WILL LEAN FORWARD TO GIVE YOU ROOM TO REMOVE THE OUTER PART OF THE AXLE,THEN BE CAREFUL,BUT USING THE RIGGT PRY TOOL,REMOVE TE AXLE

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I04 Lincoln Navigator. Front differential pass seal leak. remove the drive shaft and unbolt the flange. the inner flange does not have a bolt to access the seal and bearing. How is the seal accessed?


If I understand you correctly the drive shaft you took out is actually a CV axle. The inner axle shaft goes into the diff. That is held in with a snap ring in the diff. It might not come out easy, sometimes they do, use a pry bar to pop it out. Be careful not to break or damage the aluminum housing. There have been times where I had to use a strong air hammer to beat on the back side of that flange to get the axle shaft out... It's sort of like taking a CV axle out of a front wheel drive car.

Oct 27, 2017 | Lincoln Cars & Trucks

1 Answer

Replacing left inner front axle seal,procedure


need more info which make of 4x4 or passenger front wheel drive

May 19, 2016 | Cars & Trucks

1 Answer

How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

Feb 09, 2015 | Dodge Cars & Trucks

2 Answers

Rear pumkin assembly bolts in front not back how do i get it out


remove the axles then the tail shaft then the bolts . You will need a chisel and hammer as the diff center will be stuck to the housing until you break the seal from the gasket sealant

Oct 26, 2013 | 2002 Chevrolet Tracker

1 Answer

REMOVEING DIFFERENTIAL ON A 1999 300M FRONT WHEEL DRIVE


The diff is part of the trans axle automatic transmission assembly and is not a separate part that can be removed.

Oct 10, 2012 | Cars & Trucks

2 Answers

I have 99 zr2 pickup and where the cv shaft slides into the differential is leaking.i have the cv shaft off and i have to pull the old seal off but the axle shaft is in the way, do i have to drop the hole...


Open the bell. Take off the rear gear cover. U will loose all the fluid if any still in it so only remove some of the bolts loosen leave like 3 in around the bottom loosen them out a oil pan under the cover pry the cover off the diff leaving the 3 bolts to keep the cover from just popping off it will also help slow the rush of fluid. Once the fluid is drained remove the bolts and cover. On the inside u will se side gears. Have a helper push the axle shaft inward then u will see there is a C clip holding the axle carfully pry off the clip. Only do one side at a time. ... Then slide the shaft out where ur helper is. .. remove and replace the leaking seal. Then clean the axle. And u have to be easy sliding it in. Some times when the axle shaft is slide in u hit the end of the tube push the axle down toward the ground with variety of pressure as u push in this is tricky. But it will pop in. Then replace the clip and gentle have a helper try and pull back on the shaft. This sets the clip from falling out. Clean the bell area and scrap the old gasket off both sides if u have no replacement gasket get high heat black rtv silcone apply it to the cover or diff face and reverse the steps to install fill it with fluid and road test all this can be seen on youtube under inner axle seal repair. Good luck.

Feb 10, 2018 | 1999 Chevrolet S-10 Pickup

1 Answer

Left rear axle leaking - Dealer states $820 to fix due to many parts within the axle. Does this sound right?


fix same problem myself...these's' only 1 inner seal (differential output seal only-about 10$ each) that needs to be replace and new brake shoes (20$ part)..assumed u have rear drums and it leaked diff fluid on the brake shoes..but, i also replaced the brake cylinder (15$ part)-u have to disconnect brake cylinder to remove axle..look on internet for procedures..http://www.yotatech.com/f128/replacing-rear-axle-seals-3rd-gen-4runner-76339/..hope this helps..all dealers are ripoffs-worked at toyota for a year

Jul 31, 2010 | 1999 Toyota 4Runner

1 Answer

I have a 94 jeep wrangler front left axle seal bad. I took the left side apart and not sure how to get the seal back in. Do I need to open the inspection cover on the diff. and take the gears out?



Rear Axle Notes
  1. Raise and support vehicle.
  2. Remove rear wheels.
  3. Scribe alignment marks on propeller shaft and axle for proper assembly, then disconnect propeller shaft from axle.
  4. Disconnect the track bar from axle mounting bracket.
  5. Disconnect parking brake cable at equalizer.
  6. Disconnect shock absorbers at axle tubes.
  7. Disconnect hydraulic brake hose at rear axle Tee-fitting, then tape ends of hose and fitting to prevent contamination.
  8. Disconnect axle vent tube from axle.
  9. Remove U-bolts and tie plates.
  10. Loosen spring mounting bolts.
  11. If equipped, disconnect ABS wiring connections at axle.
  12. Support axle with suitable jack.
  13. Remove spring-to-shackle attaching bolts and lower spring to the floor.
  14. Remove axle assembly.
  15. Reverse procedure to install.

Front Axle Notes
  1. Raise and support vehicle at frame behind front springs.
  2. Remove front wheels.
  3. Scribe alignment marks on propeller shaft and axle yoke for proper assembly, then disconnect propeller shaft at axle yoke.
  4. Disconnect connecting rod at steering knuckles.
  5. Disconnect shock absorbers at axle housing.
  6. Remove stabilizer bar connecting links to spring tie plates attaching bolts, if equipped.
  7. Disconnect breather tube at axle housing.
  8. Disconnect stabilizer bar link bolts at spring clips.
  9. Remove disc brake calipers, rotors and brake shields.
  10. Remove U-bolts and tie plates.
  11. Support axle assembly with suitable jack to relieve spring tension.
  12. Loosen rear spring shackle to spring attaching bolts.
  13. Remove front spring shackle to spring attaching bolts and lower spring to floor.
  14. Remove axle from under vehicle.
  15. Reverse procedure to install.

Jul 21, 2009 | 1994 Jeep Wrangler

1 Answer

Change front differential seals in 1996 gm sierra


In order to replace the seals, remove the front diff assembly. To remove the passenger side seal, I would suggest removing the tube assembly (5 bolts). This is due to a steel washer that goes on the end of the axle. If you just pop the axle out, it is tough to get the washer aligned and back on the shaft. Use anerobic sealer to seal the housing to the diff case. The drivers side you can pop out with a hammer.

Jul 02, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Front axle how to remove half shaft


Hi.. The step to remove the front Axles of you Vitara.
Raise and support Vehicle . Remove front wheel,
Drain Diff,fluid,
Remove Locking Hub if is equipaded,
Remove Circle clip from axle shaft
On right side of Vehicle, Remove the Stabilizer Little ball joint nut. Remove castle nut Front Tie rod end,
Remove mounting bolts from brake calipper,
Remove Calipper from steering knuckle and wire a side.
Remove Stud Nut from steering knuckle,
Support Lower suspension arm with a jack,
Remove lower strut bracket bolt ,
Lower jack and disconnect Knuckle from lower suspension crontrol arm,
Pull Outler joint from Hub.
Use Large screwdriver or Prybar To pry Right inner joint from differential, The axle will go out making a little froce with the prybar,
To remove the left side,
Remove mounting bolt from inner joint flange,
Pull out axle from hub.

To reinstall just reverse the prosses.

I hope this help on your job...
Thank you for use fixya....


Aug 18, 2008 | 1999 Suzuki Vitara

Not finding what you are looking for?
2002 Chevrolet Tracker Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...