Question about 2007 Chevrolet Equinox

Open Question

How do you test the rear wiper switch on a 2007 equinox? also how do you get the rear switch out ?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76109 Answers

SOURCE: How do I seperate the rear wiper arm from the

GO TO THE LINK FOR INSTRUCTIONS

http://www.streakfreewiperblades.com/site/990209/page/813439

Posted on Oct 14, 2009

Ad
gripfitter
  • 557 Answers

SOURCE: The arm on my rear wiper does not move.

remove the arm to see if the motor turns. Look inside where the arm mounts, is the inside worn out?

Posted on Dec 23, 2009

ZJLimited
  • 17970 Answers

SOURCE: where is the fuse located

From owners manual...

zjlimited_750.jpg

...check position 3 for rear wiper. The instrument panel fuse block is located on the passenger's side of the center console, to the left of the glove box near the floor.

Hope helps.

Posted on Feb 26, 2011

princeofscot
  • 288 Answers

SOURCE: rear wiper dont work on 2007 equinox

if you know how to use a multimeter or someone who does can go inside the motor to see if the motor wires connected to it is getting enough current electrons to it to make it work but the motor might went bad on you so have someone check this out first but also check your fuses too when you have the chance as well, It does not hurt to check all fuses.

Posted on May 27, 2011

  • 1 Answer

SOURCE: How do I replace the rear windshield wiper motor

How to remove rear wiped from a 07 equinox

Posted on Aug 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is it my 2008 chevy uplander rear wiper motor/blade moves some and stops. I let van set 5-10 minutes with key off. Turn on key. Wiper motor/blade moves a few degrees and then stops again. Why?


Can you move the wiper by hand ? Which does your vehicle have ?
WDA/Z88 The rear wiper is controlled based on an input from the rear wiper/washer portion of the multifunction switch. When closed, the wiper ON and wiper DELAY switches provide a unique voltage signal to the rear window wiper motor indicating the desired speed. Each switch has a unique resistor that drops the voltage to a specified value which is interpreted by the rear window wiper motor as ON or DELAY. The rear wiper motor receives B+ voltage from the I/P fuse block and accessory voltage from the body control module (BCM).
W49 The rear wiper is controlled based on an input from the rear wiper/washer switch. When closed, the wiper ON switch provides a voltage signal to the rear window wiper motor indicating rear wiper operation is requested. The rear wiper motor receives B+ voltage from the I/P fuse block and accessory voltage from the body control module (BCM).
Do you know how to do electrical testing ?
WDA/Z88
  1. Ignition OFF, disconnect the harness connector X1 at the multifunction switch.
  2. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 4 and ground.
  3. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, refer to Power Mode Mismatch.

  4. Ignition OFF, connect the harness connector at the multifunction switch. Disconnect the harness connector at the rear window wiper motor.
  5. Test for less than 20 ohms between the ground circuit terminal B and ground.
  6. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  7. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal A and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  9. Verify a test lamp illuminates between the ignition circuit terminal E and ground.
  10. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  11. Rear wiper switch in the ON position, test for B+ between the signal circuit terminal D and ground.
  12. ?‡'
    If less than the specified value, test the signal circuit for an open/high resistance. If the circuit tests normal, test or replace the multifunction switch.

  13. Rear wiper switch in the DELAY position, test for B+ between the signal circuit terminal D and ground.
  14. ?‡'
    If less than the specified value, test or replace the multifunction switch.

  15. If all circuits test normal, test or replace the rear window wiper motor.
W49
  1. Ignition OFF, disconnect the harness connector at the rear wiper switch.
  2. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 6 and ground.
  3. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, refer to Power Mode Mismatch.

  4. Ignition OFF, connect the harness connector at the rear wiper switch. Disconnect the harness connector at the rear window wiper motor.
  5. Test for less than 20 ohms between the ground circuit terminal B and ground.
  6. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  7. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal A and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  9. Verify a test lamp illuminates between the ignition circuit terminal E and ground.
  10. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  11. Rear wiper switch in the ON position, verify a test lamp illuminates between the signal circuit terminal D and ground.
  12. ?‡'
    If the test lamp does not illuminate, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the I/P switch assembly.

  13. If all circuits test normal, test or replace the rear window wiper motor.
Component Testing

Do you know how

Jun 09, 2016 | 2008 Chevrolet Chevrolet Uplander LS

2 Answers

Rear wiper dont work on 2007 equinox


if you know how to use a multimeter or someone who does can go inside the motor to see if the motor wires connected to it is getting enough current electrons to it to make it work but the motor might went bad on you so have someone check this out first but also check your fuses too when you have the chance as well, It does not hurt to check all fuses.

May 27, 2011 | 2007 Chevrolet Equinox LS New Cars

1 Answer

Where is the fuse located for the rear wiper motor for a 2007 chev equinox


From owners manual...

zjlimited_750.jpg

...check position 3 for rear wiper. The instrument panel fuse block is located on the passenger's side of the center console, to the left of the glove box near the floor.

Hope helps.

Feb 26, 2011 | Chevrolet Equinox Cars & Trucks

3 Answers

Rear wiper stopped working


First check the fuse for the rear wiper to make sure it did not blow. Also, if you had the wiper replaced resently, then the nut on top of the wiper blade may not have been tightened down.

Nov 28, 2010 | 2007 Chevrolet Equinox LS New Cars

1 Answer

I put the back wiper on earlier in the week to clean off the frost. It swiped across the window once and has since quit working. I have the switch off but we can hear a noise in the rear door and also...


Sounds like your rear wiper switch has shorted. If you can pull it out of the dash or get the panel off and get behind the switch you can disconnect it and see if that stops it. If it does you can get a new one later and replace it.

Nov 07, 2010 | Chevrolet Equinox Cars & Trucks

1 Answer

The arm on my rear wiper does not move.


remove the arm to see if the motor turns. Look inside where the arm mounts, is the inside worn out?

Dec 22, 2009 | 2007 Chevrolet Equinox LS New Cars

Not finding what you are looking for?
2007 Chevrolet Equinox Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...