Question about Cars & Trucks

1 Answer

Need direction for assembly - Cars & Trucks

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Cars & Trucks Expert
  • 180 Answers

Assembly of what?

Posted on Mar 30, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing rear directional


Pull back the carpet in the trunk on the side the bad bulb is.simply turn the bulb counter clockwise to remove it. If you need to remove the complete light assembly get a deepwell 10mm socket and remove the 3 quick nuts and remove assembly. Good luck.

Mar 04, 2014 | 2003 Chevrolet Cavalier

1 Answer

How to remove head light?


I have removed the entire assembly before and it wasn't very difficult. From memory there are a few screws to undo and then the whole assembly slides out. I found the directions in the manual in the section on replacing headlight globes.

Feb 12, 2014 | 2007 Hyundai Santa Fe Limited

1 Answer

I need to change a left side directional light the left side directional light is not working so it need to replace it is a dodge caravan 1996


To replace your turn signal - There are 3 screws on the front of the light assembly. Remove them and slide the light assembly out and you will see the turn signal socket is in the middle of the outer half of the headlight assembly. Twist the socket counter clockwise to take it out of the assembly. Pull the turn signal bulb straight out from the socket. Insert new bulb and reverse procedure to finish.


Mar 12, 2011 | 1996 Dodge Caravan

1 Answer

How do i install a hub assembly for my right front wheel on my 1992 jeep cherokee?


jack it up , take the wheel off, take brake assembly off, should be 3 bolts on back side of hub assembly, take those out( you'll need a cold chisel, a hub puller, and maybe a torch, once u get the hub off, follow the directions in reverse.

Oct 28, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

How do you change a parking light?


front: pop hood, look behind the lense for the assembly. twist and remove the assembly. twist bulb out of holder. put in new bulb. put back in, twist into place (opposite direction).
rear: pop trunk, may need to remove a panel to reveal the assembly. same directions.

Sep 18, 2010 | 2005 Mazda 6

1 Answer

Change left headlight bulb


Open the hood and directly behind the headlamp assembly there are 2 plastic sometime metal tabs that you need to pull up on.This releases the headlamp assembly.Then pull out on the headlamp assembly and replace the bulb.Check and make sure it works before you put it back together.Good luck.

Dec 07, 2009 | 2001 Pontiac Grand Am SE

1 Answer

Need directions for replacing a hub bearing assembly on my chevy silverado 1500, 2003, 4 wheel drive pickup.


REMOVE BRAKES, ON BACK SIDE OF SPINDLE REMOVE FOUR RETAINING BOLTS AND HUB ASSEMBLY SHOULD COME OFF.. MAY HAVE TO TAP WITH A HAMMER TO BREAK FREE FROM THE SPINDLE... BE SURE TO THOUOUGHLY CLEAN THE SPINDLE BEFORE INSTALLING NEW BEARING ASSEMBLY.

May 07, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

Electric window assembly.step by step


what kind of directions do you need?

Apr 23, 2009 | Ford Bronco Cars & Trucks

1 Answer

Need clutch replacement directions for Ford Ranger


Remove drive shaft,remove crossmember under transmission.Remove transmission and diconnect linkage.Remove bell housing,and clutch berring assembely.Remove bolts on pressure plate.Once this is done.Remove fly wheel for machineing.you will need a pilot shaft to alighn clutch assemblely.Possible one will come with new clutch and pressure plate.Reverse assemblely in same order remember to torque all your bolts with torque wrench.Take your time.

Apr 19, 2009 | 1994 Ford Ranger Supercab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...