Question about 1996 Toyota Tacoma

1 Answer

Me and a find bought a 96 Toyota Tacoma. we drove it and it went put not very willingly. we it wont move at all. we replace the slave. it feels like its going into gear but it don't cut of even when you let off the clutch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Toyota Master
  • 880 Answers

Did you bleed the master cylinder for the clutch and the slave cyclinder for the clutch

Posted on Mar 30, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 ford 4.9 5 speed hydrolich clutch wont shift all of a sudden new master cylinder


You have a leak and you have air in the system. More than likely the slave cylinder is leaking, the slave is a direct acting one and as with all direct acting slave cylinder it is located inside the transmission bell housing on the transmission input shaft collar. The transmission must be removed to replace it.

Jun 23, 2012 | Ford F150 Cars & Trucks

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

1 Answer

I have 1997 Toyota tacoma v6 4x4 I replaced clutch drove next day with no problems got in following and now won't engage/ disengage from gears. if turn off I can put in first or reverse but struggles....


Check the clutch master cylinder and the clutch slave cylinder for proper operation... chances are the slave is bad.. I think this is located on the passenger side of the tranny.. you may have lost fluid during the install.. or introduced air into the system.

If you needed a new clutch.. it was probably time to at least flush that system and or replace the slave cylinder.. also check the spring on the clutch pedal..

I hope you replaced the throw out bearing and pressure plate when replacing the clutch.. I suspect you did.

Best of luck

Mar 26, 2011 | 1997 Toyota Tacoma

1 Answer

My clutch went out on ac in my 1998 toyota tacoma 6cyl. I was told i need to repace verything. If so what parts do i need?


First check the slave cylinder for the clutch, this could be the only issue, if your hydrailics fail your clutch won't work

If you do indeed need to replace the clutch replace everything Clutch disk, Pressure plate, Throw out bearing, and Fly wheel This is not a job that you want to have to do again in 6 months
Most auto parts stores will sell a kit containing everything you need

Apr 02, 2010 | 1998 Toyota Tacoma

2 Answers

2006 4cyl manual 5 speed transmission 30K miles, light use with no problems. Will not go into any gear with engine running, goes smoothly into every gear with engine stopped. Clutch pedal feels fine and...


Well, there is only one thing I can think of in your situation. Your pressure plates just simply are not creating enough pressure to allow the gears to engage. Either you have a defective clutch and it needs to be replaced, or possibly just needs a ton of adjustment. When you put it in 1st gear while engine is off, then start it and take off that works b/c there is enough pressure to keep the gears from starting to move when not already moving. However when they are already moving, there is just not enough pressure to stop them from turning, not even long enough to shift. Have you tried forcing it into 2,3, or 4 while driving without the clutch? As long as you achieve the correct RPM's your transmission should be able to do so.

Feb 13, 2010 | 2006 Toyota Tacoma

1 Answer

Clutch 1998 toyota tocoma


Replace master cylinder

Mar 11, 2017 | 1998 Toyota Tacoma

1 Answer

Front axle - front drive shaft Toyota tacoma 1998 4x4


more than like have a broken axle shaft, un hook the rear drive shaft and put it in 4wd if it wont move then you know you got a broken axle shaft or spider gears broke in the pumpkin

Dec 09, 2008 | 2007 Toyota Tacoma

Not finding what you are looking for?
1996 Toyota Tacoma Logo

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...