Question about Cars & Trucks

1 Answer

Engine pressure, 206 2lt hdi. dip stick pop's up and filler cap unscrews, why ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Cars & Trucks Master
  • 372 Answers

If your getting enough pressure to push out dipstick i wood check pcv valve for being clooged or you are leaking compression into crankcase. ( bad rings)

Posted on Mar 29, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much oil do I put in my car 19 00 cc


1. Turn off engine ,
2. Take of oil cap on engine
3. Put in a little oil in oil filler hole of engine.
4. then pull out the oil dip stick from engine
5. and clean the dip stick on a rag.
6. Put dip stick back in engine
7. pull out again and check the level showing on the dip Stick
8. If level is too low on dip stick and is not at full level go back to step 1

These steps ensures you avoid over filling the engine with oil

Tip for beginners
The 4 litre oil bottle is way too much oil for an engine to handle.
If you have a full 4 litre oil plastic bottle square shape . hold the bottle on its side to pour the oil out slowly and smoothly.

Jun 04, 2016 | 2005 Mitsubishi Carisma 1.6

2 Answers

Condensation under oil filler cap


Car spitting some oil on the filler cap may be normal, if it spits out oil from the cap there is a problem. check oil level and eventually have an oil change.

Jul 31, 2008 | Mercedes-Benz E320 Cars & Trucks

1 Answer

Where is the oil dip stick located on 2002 cavalier 4 cyl


If you can't see separate oil dipstick (usually has an yellow plastic handle), then your oil level dipstick is connected to oil filler cap. When you unscrew the oil cap you'll be able to see the dipstick and level meter.

Sep 23, 2014 | 2002 Chevrolet Cavalier

1 Answer

Where is the oil dip stick located on 2002 cavalier


On most Cavalier motors the dip stick i s part of the filler spout you just remove the filler cap and pull the stick out with the cap. Make sure you check the oil with the motor shut off

Sep 23, 2014 | 2002 Chevrolet Cavalier

1 Answer

How to check transmission fluid


look the trans dip stick. it be found underneath, at right side of the transmission(passenger side). it has plug where the filler tube would normally go. unscrew the plug there's the dip stick inside.

May 22, 2012 | 2007 Ford Expedition Eddie Bauer EL

1 Answer

Procedures to change engine oil on 1997 Audi A4


the long answer is...put engine flush in oil, run for about 1 hour,switch off/remove key,then remove splash guard from under the engine (best done when car on ramps)then remove oil filler cap and drain plug on sump(oil pan).whilst draining into an empty can with the side cut out(drip tray) locate oil filter and punch a hole in the side of it with a screwdriver,and unscrew it.
Wipe oil onto the rubber seal of the new filter and screw onto carrier.hand tight only.
then replace sump plug washer(copper/fibre)and replace using a 6"long ring spanner and do up tight.
(max pressure of palm of hand)
put in about the same amount of oil that came out,replace oil filler cap and start engine.
check for any leaks,replace splash guard and lower car to level surface,turn off engine,leave for 60 secs,then dip for oil level and top up to midway on dipstick,
job done....
use 10/40 semi synthetic oil.

May 21, 2010 | 1997 Audi A4

3 Answers

Where is the oil dip stick in the 1998 saab 900


u can find it near gear oil stick yellow colour

May 02, 2009 | 1998 Saab 900

1 Answer

I have a 1999 323I BMW and i think i need antifreeze but i'm not sure. A light came on and it is a picture of a tank with liquid in it with a spout...i'm not sure what that icon means on my dashboard. ...


either is antifreeze or is the oil light.
cooling tank is in the front of the car. look for a fan, the cooling tank is infront of the fan. open the cap (make sure the car is cold). and see if there is water or antofreez in it. add as you needed. also follow a tube from the side of the filler neck. you should see a container, that should be a over flow container. fill that to the line on the container. close the cap. and make a 90 degree turn. it should be tight.
the oil is on the button of the engine. you should see a dip stick with a color handle near the engine. pull it out and use a paper towel clean it, put it back and pull it out again. take a look at the tip of the stick. there should a marking indicating where the oil should be. half qt of oil if dip stick shows half way between the mark, and full qt if the dip stick indicated below the marker. fill the engine (filler is on top of the engine.) with oil.

Apr 16, 2009 | 1999 BMW 323 Series

1 Answer

The oil is running out from the oil filler cap


Make sure the pcv valve is working correctly and allowing the engine to breath

Nov 20, 2008 | 1994 Volvo 850

3 Answers

How to fill transmission fluid in a 2006 pontiac G6 Gt


There should be a screw on the front of the trani near the coolant lines. With the engine off you unscrew the filler cap. That's on top of the trani on the driver's side. It has a little gear in fluid symbol on it. Then you take out the screw on the front and fill until fluid comes through the hole left by the screw. Remember to use Dex VI.

Aug 28, 2008 | 2006 Pontiac G6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...