Question about Cars & Trucks

1 Answer

Did stick and filler caps pop's up.why - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 49 Answers

Try replacing the pvc valve if that don't work then you have ring problems

Posted on Mar 29, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Problems opening the gas cap for removal when gassing up my 2004 Buick Rendezvous. Just bought a new cap and same problem, won't open


If the cap is hard to remove, this is a common problem with older GMs. The mating surface at the end of the filler tube becomes slightly corroded and is sticking to the rubber seal on the cap. Plug the filler tube with a rag (to avoid any explosive hazard), clean the mating surface with lacquer thinner, gently buff it with crocus cloth and try that. If it still sticks, lubricate the cap rubber seal with a thin coat of a lubricant (ONLY one approved for rubber/plastic materials).

Jan 03, 2017 | Buick Cars & Trucks

1 Answer

Engine pressure, 206 2lt hdi. dip stick pop's up and filler cap unscrews, why ?


If your getting enough pressure to push out dipstick i wood check pcv valve for being clooged or you are leaking compression into crankcase. ( bad rings)

Mar 29, 2015 | Cars & Trucks

1 Answer

How to replace fuel tank filler tube?


Brother John, you've removed as much as you can for access to the filler. Remove the hose clamps/bands that secure the fill tube and vent tube and then remove the screws around the gas cap that secure the fill tube to the body. With the gas cap off, go below and pull the hose and filler neck down and work the hoses lose with a pair of channel lock pliers and sticking a screwdriver between the metal tube and hose to break the seal. Put on the new filler neck and stick it back up in the body and put the screws back in. THEN put the hose clamps back up and tighten them, put the gas cap back on and your done.

Nov 30, 2014 | 2000 GMC Jimmy

1 Answer

Where is the oil dip stick located on 2002 cavalier


On most Cavalier motors the dip stick i s part of the filler spout you just remove the filler cap and pull the stick out with the cap. Make sure you check the oil with the motor shut off

Sep 23, 2014 | 2002 Chevrolet Cavalier

1 Answer

1997 Mercury Sable coolant cap pops off when engine is warm


Is the filler neck worn or you may need a new cap

Jan 14, 2013 | 1997 Mercury Sable

1 Answer

2002 chevy tahoe gas cap door wont stay closed


Hello Matthew, Check the hinge on the door and the retainer latch button inside of the filler neck area. Sometimes they stick and won't pop out back out to keep the fuel door latched properly. You can lube the hinge & latch with WD40 to free it up. I have seen this happen a few times on a Blazer. Hopefully, this is all you need. I hope this information is helpful.

10_12_2011_8_14_26_pm.jpg

Oct 12, 2011 | 2002 Chevrolet Tahoe

1 Answer

How to remove the fuel filler neck on my 1999 Dodge Grand Caravan 3.8 ltr. engine


OPEN GAS CAP FLAP THEN YOU NEED TO DRAIN GAS BELOW FILLER NECK.THEN LOOSEN REMOVE SCREWS IN THE GAS CAP FLAP AREA WHERE FILLER TUBE CONNECTS THEN GO UNDERNEATH VAN LOOSEN REMOVE HOSE CLAMPS AND REMOVE THE HOSE AT THE FILLER NECK BELOW THE GAS TANK.SPRAY WD40 AROUND HOSE AREA AT METAL FILLER TUBE STICK OUT GAS TANK.CAREFULLY USE LARGE PAIR OF CHANNEL LOCK PLIERS TO REMOVE WORK HOSE OFF METAL TUBE FROM GAS TANK. IF YOU CANT REMOVE HOSE WITH HANDS.BECAREFUL NOT TO MAKE ANY SPARKS.PLACE RAGS AROUND ANY METAL PARTS TO KEEP CHANNEL LOCKS FROM HITTING METAL MAKING SPARKS.

Jun 23, 2011 | 1999 Dodge Grand Caravan

1 Answer

Filler flap wont open when release pulled in car cable looks connected at front


pop the trunk there is a handle in side right near the filler cap pull handle if it pops then it is cable at 1 end or other if it doesnt pop then it is likely a spring

Jan 23, 2010 | 2002 Jaguar X-Type

1 Answer

Honda


filler cap is same as the check stick. if you are standing in front of the car looking at it, it will be on the left, straight down to the rear of the radiator. most of them are yellow in color and very short

Jun 22, 2008 | 1991 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...