Question about Cars & Trucks

1 Answer

Lcd display breaking up can not read properly

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 7,733 Answers

You need to check you electric system with a PRO.

Posted on Mar 29, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2002 jaguar s type, i had been out in the car with no problems when i went to go out in it later the oil light stays on the oil level is fine. the display also reads parking break fault. the fuel...

check your resistors,fuses may work fine but if resistors are not then these faults may appear...also try a hard reset unplug the neg battery terminal for 30 minutes....then plug it back make sure when you crank the car press the brake paddle and hold it then engage the park brake lever with your hand...then shift the car to drive then the brake module will reset properly...keep me posted

Sep 10, 2011 | 2003 Jaguar S-Type

1 Answer

Lcd display on my peugeot 206 does not work.

it may be the back light bulbs that need replacing. to check for this simply shine a torch on to the display and you should be able to see the read out.

let me know if this helps

cheers big mike

Mar 29, 2011 | 1983 Peugeot 504

1 Answer

Sputtering engine and break problems, 2000 Ford Focus

The brake pedal issue is a lack of vacuum in the engine while not idling properly. There are quite a few reasons for this issue. I would have the engine codes read first to see if you have a fault code for any of the sensors. It could be any of the following, Map Sensor, TPS Sensor, O2 sensor, Temp Sensor, Fuel pressure regulator, Air intake Temp, fuel pump, broken wire, bad connection or a few other things.
Have the codes checked first to help rule out some of the more expensive items.

Jul 27, 2010 | 2000 Ford Focus

1 Answer

Air temp indicator only reads temps below 50 degrees

Ambient air temp sensor could be the cause. Normally located in front grille area.

Oct 06, 2017 | 2002 Chevrolet TrailBlazer

2 Answers

My 2000 renault scenic lcd display is not illuminated what could be wrong

The lcd screens give a lot of trouble they break very very easy and can rarely be fixed best bet is to get a dealor to have a quick look at it they prob wont even charge you.

Dec 10, 2009 | 2000 Renault 181

1 Answer

2006 Mazda3 with crazy flashing LCD display

I disconected the negative battery cabke and keft it off for about one hour. When it was reconnected the display retruned to normal except the temperature now reads in C instead of F. I don't know if the time it is disconnected has any inopact, but doining this essentially resets the display. Goof luck!

Sep 09, 2009 | 2005 Mazda 3

1 Answer

LCD display

I had this happen when I first had my car they replaced my stereo under warrenty. then about 5 yrs later did it again. No known cause I just ignore it now

Jul 11, 2009 | 2002 Pontiac Grand Am

1 Answer

Power windows will not work gauges speedo and tach all read o when drivers door is closed when opened all work properly on a 1999 jeep grand cherokee

Check the dash for proper grounding and also check the door harness where it passes through the boot for breaks or shorting. The door may be completing the body ground through the latch.

Jun 14, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Center information display hard to read


Mar 14, 2009 | 1999 Audi A6

1 Answer

2004 Ford F150 Guage Cluster LIghts are out

FROM LustyKid:

You have to remove the dash panel be careful you don't break the string for the shift indicator which slides on and off. You will need to bring the shifter (column one) to the low position so you can pull out the dash. Lots of screws different sizes, don't interchange them. Don't over tighten them either, you crack the plastic in the dash panel and strip them. Good luck

Nov 24, 2008 | 2004 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15148 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides