Question about Cars & Trucks

2 Answers

Brakes have plenty of fliud pedals hard but don't seem ta wana stop

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

It could be either your discs need changing as the suface area is bad one or 2 pads are low or you have brake cables that are old and expand under pressure taking it away from your calipers or the manifold is failing and pressure getting out from there
this will put air in the braking system and will fail
i would go straight to a rep garage and get checked out tomorrow as its not just your life but others it can and will effect it they fail and sounds like they will

Posted on Mar 29, 2015

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,039 Answers

What model brake booster problem or abs pump doesnt work with model i could help you

Posted on Mar 29, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: hard pedal low stopping power

Poor braking may be due to severely worn pads (disc brakes) or shoes (drum brakes), however, a common cause of "sudden" hard braking is the power brake booster either losing vacuum or failing, causing the brake sytem to lose the assist the booster provides and requiring a stronger effort by the driver to slow or stop the car by "standing" on the brake pedal with much greater force.

Posted on Jul 19, 2008

  • 79 Answers

SOURCE: excessive brake pedal travel

pump the brakes a few times they should stiffen right up

Posted on Mar 22, 2009

landsend
  • 1066 Answers

SOURCE: brake pedal goes hard and brakes dont work

no a new brake master cylinder.

Posted on Mar 25, 2009

  • 15 Answers

SOURCE: brake light stays on at times the brake pedal is hard

brake light switch under brake pedal

Posted on Jan 13, 2010

  • 1 Answer

SOURCE: 95 f350 hard brake pedal

did you get your brakes fixed? If so what was wrong?

Posted on Dec 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BRAKES BLED PEDAL GOES TO FLOOR WHEN STARTED


if a master cylinder is bad and you are sure you have all the air out and no leaks.pedal will go to floor , running or not. if booster is bad it will cause a hard pedal. but if master cylinder is bad it will turn on a brake light on dash if it works. make sure the wheel cylinders are not leaking. I beleive that the master cylinder is bad, or you have a leak somewhere. If the master cylinder is functioning properly, the brake pedal will depress to a certain depth and no further.

Apr 20, 2012 | 2000 Chevrolet Blazer

1 Answer

Brake pedal has alot of back pressure and car moves in gear.Have to press real hard to stop.How to check abs pump if has one where or brake booster or master cylinder?Don't know how to trouble shoot or...


The air seeping is a dead giveaway. Your power brakes are now manual brakes, but stiffer. The diaphram in the brake booster has torn and the hissing noise is the engine vacuum escaping (you hear it louder when you depress the pedal right?). Replace the booster and you will be fine. The brake lights probably don't work because you can't push the pedal down far enought to release the switch. Please rate. Thanks.

Sep 03, 2011 | 1995 Mercury Cougar

1 Answer

What happen when your brakes don't work write sometime you stop in it will get hard are stuck sometime.


i dont get your ? but you may wana check your liquid on your brakes also your brake pads

May 30, 2011 | Pontiac Sunfire Cars & Trucks

2 Answers

I replaced front and back brakes on my 1996 1500 Chev Suburban. Bled the brakes starting at the farthest line. The pedal is soft and travels too far. Does not seem to stop very good. What is the...


it sounds like there is still air in the brake system that has not been removed.you don`t say if you replaced the brake pads and shoes(in which case you shouldn`t need to bleed)or you replaced a brake line(s) or wheel cylinder or caliper.you will have to keep bleeding the brakes all 4 wheels(trucks don`t use bi-directional braking meaning right rear brakes with left front and so on).bleed both rear brakes then bleed both front brakes,was this problem there before you replaced the brakes(soft pedal noticed) and this is why you changed the brakes or the pedal was soft and the brakes needed changing.its possible that the master cylinder has an internal leak and may need replacing.

Apr 06, 2011 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

It has new brakes but the abs light came on and now the brake pedal is hard and I barely have any brakes


If the person who did the brakes did not release the bleeder screws on the front brake calipers to prevent pushing brake fliud back into the anti lock hydralic unit when retracting the brake caliper pistons they may have damaged the anti lock unit. Try doing a complete beed out of the brake fluid front and back to regain function.

Sep 18, 2009 | 1993 Dodge Caravan

2 Answers

Brake fade on a honda accord


here are the possibility, air in the brake line, brake line has a hole, no brake fliud, master brake cylinder bad.
need to bleed the brake lines and see if there is ahole in any of the brake lines. if not, then your master brake cylinder need to be replaced.

Apr 15, 2009 | 1995 Chrysler New Yorker

2 Answers

Boiling brake fliud with continous braking when driving


your calipers are hanging up and causing the brakes to drag and hence heat up.  Is your emergency brake working OK and releasing properly

Apr 06, 2009 | 1998 Ford Escort

1 Answer

Excessive brake pedal travel


pump the brakes a few times they should stiffen right up

Mar 22, 2009 | 2004 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...