Question about 2000 Jeep Grand Cherokee

1 Answer

2000 jeep grand Cherokee p0132 code is on and changed the o2 sensor.... the code comes right back on and doesnt run good at all and wants to die any other ideas for me before I take it to a shop

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Jeep Master
  • 1,168 Answers

A code P0132 may mean that one or more of the following has happened: The oxygen sensor heater circuit is shorted out The wiring to the sensor is broken / frayed (less likely)

Possible that the wire is bad some where , was that on my wife's car

Posted on Mar 29, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76164 Answers

SOURCE: P0132 code along with P0300, P0301, P0302, etc.

check for intake manifold for vacuum leaks, use a can of spray carb cleaner and spray around the top of the engine, if you hit a leak the engine idle will change, P0302 is a miss in #2 cylinder (cylinder power output low, lean cylinder due to poss vacuum leak and other issues.). once again an O2 will not cuase a mis-fire.

Posted on Mar 17, 2009

maygemini
  • 147 Answers

SOURCE: Radiator fan will not turn off in my 2000 Jeep Grand Cherokee

usually the engine relay or cooling fan relay..!

Posted on May 08, 2009

GM Elec
  • 1000 Answers

SOURCE: 2000 grand jeep cherokee dies while slowing down

Its not unusual for the crankshaft sensor to intermittanly fail. The crank sensors are not real expensive and are not extremely hard to change.
The Crankshaft Position Sensor (CKP) is mounted into the engine block above the starter motor. Engine speed and crankshaft position are provided through the crankshaft position sensor. The sensor generates pulses that are the input sent to the powertrain control module (PCM). The PCM interprets the sensor input to determine the crankshaft position. The PCM then uses this position, along with other inputs, to determine injector sequence and ignition timing. The sensor is a Hall effect device combined with an internal magnet. It is also sensitive to steel within a certain distance from it.
Below is a pic of the sensor location.
Good luck.
Regards,

4732b83.gif

Posted on Jul 23, 2009

  • 3640 Answers

SOURCE: 2002 jeep grand cherokee with 4.0 engine will die but restart

p0340 is the cam shaft sensor, this will cause it to cut off while driving, hardtime starting, p0351 is the ignition coil A primary/secondary curcuit mal function. p1391 is ignition system misfire, this could be plugs, wires, or coils. first of all have the cam sensor changed and it may correct the rest of the codes. when fixed turn light off with obd2 scanner. if you do not have one, then any auto parts store will erase the codes fo free of charge.

Posted on Jan 21, 2010

  • 2926 Answers

SOURCE: 2005 jeep grand cherokee trouble code p2096 change

These conditions MUST be ruled out entirely.
Check for any of the following conditions/mechanical problems.
AIR INDUCTION SYSTEM - must be free from leaks
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions or leaks
ENGINE PCV SYSTEM - must flow freely
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to correct injector.

Unfortunatly, a scan tool will be required to monitor o2 sensor voltages while the engine is running in closed loop. This code you are displaying is NOT an easy solution to trace down. I expect you had an exhaust leak and is why the cats were replaced? Anyway, if so, the PCM can reset the light after a few GOOD trip readings occur that will satisfy the PCM's no fault signal, otherwise the JEEP dealer is going to be your only solution and a pressure test should be performed.

Posted on Mar 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Trouble codeP1491,P0132,P0135 on 1999 Jeep Grand Cherokee 4.0 What does this mean?


P1491-This code is for the radiator fan control relay circuit.
This can be caused by bad wiring, a faulty fan, a bad thermostat and even a bad pcm. Most likely it is a wiring issue.
P0132 This involves the front oxygen sensor on Bank 1. This code indicates that the heated oxygen sensor reading is too high.
P0135 This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop.
As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135. You need a new Bank 1 sensor 1 O2 sensor !

Feb 14, 2015 | 1999 Jeep Grand Cherokee

2 Answers

O2 sensors


double posted, back up one ,please.

Apr 14, 2014 | 1998 Jeep Grand Cherokee

1 Answer

2000 Jeep Grand Cherokee codes p0132 p0141 p0152 p0161 Keep Coming Back


Then the problem, is not fixed and needs further diagnosis using special equipment..

May 31, 2013 | 2001 Jeep Grand Cherokee

1 Answer

'99 Jeep Cherokee. Dies within 10 min of driving


Have you scanned the system for fualt codes? An O2 sensor will never cause the engine to stall out like this, NEVER.

May 10, 2012 | 1999 Jeep Grand Cherokee

1 Answer

My jeep grand Cherokee will shut off and all the gauge on dashboard turn on


It could be the O2 sensor and the camshaft sensor. I have the same Jeep and having the same issues. Auto Parts stores have the sensor, just need to find a good mechanic that wont over charge you. When you do, ask then to run the codes to make sure.

Mar 21, 2012 | 1999 Jeep Grand Cherokee

1 Answer

I've changed all of the o2 sensors in my 2004 jeep grand cherokee, and the check engine light keeps coming on, saying the o2 sensonrs are bad


The wiring harnesses for the O2 sensors run right next to the exhaust manifold, and get incredibly hot, sometimes causing the wires within the harness to crack or break. This would cause your problems. Have a look at the harness and let me know what you find.

Oct 26, 2010 | 2004 Jeep Grand Cherokee

1 Answer

Error code P 0161 for 2000 Grand Cherokee Limited V8


Its related to the oxygen sensor and/or oxygen sensor heater. There are 4 sensors the Jeep is equipped with.

In most cases one of the recommended solution for all those faults is a sensor replacement, however before doing that and spending a lot of money. Go to auto zone and have them tell you what O2 sensor is bad buy it and replace it. Go back to them to have the code cleared. O2 sensors run 20-50bucks. Good Luck

Jun 20, 2009 | 2001 Jeep Grand Cherokee

2 Answers

2000 jeep grand cherokee raves up when idleing


could be an idle controll sensor...maf sensor or o2 sensor....run a good carb/fuel ingector cleaner through with with some high test gas, do this for you next 2 fill ups, one can of cleaner per full tank...if it doesnt work.. then one of those senors is playing tricks with ya...In worst case the timing belt is slipping..
hope this was helpful !

May 19, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2000 jeep dies


When there are no faults in the PCM,and the veh. stalls and starts right back up.A reel good try would be to replace the crank sensor(flywheel sensor)

Jan 14, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...