Question about Chevrolet Blazer

1 Answer

How do you adjust shift linkage on a 1999 chevy blazer s-10

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 880 Answers

Disconnect cable at the transmission. pull the shift lever on trans to lowest gear. do the same inside the car. adjust cable to fit. make sure it goes into park easily and completely

Posted on Mar 30, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: chevi blazer 1999 transmissioin shift problem

1- STOP THE VEHICLE
2- MAKE SURE IS IN NEUTRAL POSITION
3- ACTIVATE 4WD (HIGH) MODE( MANUAL OR ELECTRONIC SWITCH SELECTOR
4- MOVE LEVER SHIFT TO ''D' DRIVE POSITION
IF THIS DOES NOT RESOLVE CHECK TRANSFER CASE SWITCH

Posted on Aug 08, 2008

bryant329
  • 125 Answers

SOURCE: 1999 Chevy Blazer Starter

the starter is located on the passenger side lower motor. it has two bolts in it that hold it in place. it actually goes through a hole/slot in the transmission to the flex plate.

1st. disconnect the negative cable on the battery.
2nd. raise the vehicle safely and place a jack stand under the vehicle out of your way but near where you will be working(for safety).
3rd. remove the two bolts that hold the starter in place.
4th. remove the wires from the back of the starter.
5th. install in reverse order of above.

note: there may be little plates between the starter and the mounting points called shims. if there are then make sure you put them back.

Posted on Sep 24, 2008

  • 66 Answers

SOURCE: 1995 chevy s-10 blazer does not shift gears

Tell me something. Does it seem like the truck is in 3rd gear when you shift in D.If is it I know what it is.

Posted on Jan 22, 2009

  • 23 Answers

SOURCE: I have a 1999 Chevy Blazer. A scan reveals code

i had to replace mine. i went to www.rockauto.com and found them for $15 a piece. its actually really easy to do. drop the pan. at the back toward the driveshaft you will see 2 right next to each other. pop out the c clips and it should come right out. reverse those steps to put it back in.

Posted on Aug 12, 2009

  • 1986 Answers

SOURCE: how do you adjust the headlights on a 1997 chevy

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I adjusted the shift on my 1992 chevy blazer automatic, now it hesitates like its starving for gas


did you adjust the shifter or the passing gear linkage?sounds like the passing gear linkage

Mar 30, 2015 | Chevrolet Blazer Cars & Trucks

1 Answer

Why does my 1999 Chevy Blazer shift really hard into second gear without the RPM's increasing like the tranny's slipping?


Shifting hard broken modulator valve on the trany itself normally there a vacuum line connected to it

Mar 13, 2015 | 1999 Chevrolet Blazer

1 Answer

Where is the kick cble located on a 1990 chevy blazer,my blazer wont shift to 2ng gear


It is located on linkage on throttle body.ene cable is throttle cable,one is cruise if equipped, and the other one will run to the transmission. It has a button you mash to adjust.It isn't obvious but you can get a screw driver and mash release/button and adjust. called detent cable.

Feb 15, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

1993 chevy blazer won't shift into park


there is a shift linkage right onder the driver's floor pan along side the tranny that is adjustible, adjust in small incrment's at firt or u could throw the whole thing out of wack! lol

Jun 04, 2010 | 1993 Chevrolet S-10 Blazer

2 Answers

1998 chevy s-10 blazer. 4 wheel drive does not


do u have a lever control on floor if yes check adjustment of linkage if u have the dash switches check fuse and relay than check actuator for proper movement at transfer case actuator has a tendency to stick lube and or adjust

Oct 29, 2009 | 1998 Chevrolet Blazer

1 Answer

I Hard Shifting, No Speedo, Anti lock light on


1 Inspect Clutch Disc Contaminated Clutch or Pressure Plate Surface. 2 Inspect Clutch Disc Worn or Damaged Clutch Pressure Plate. 3 Inspect Clutch Disc Improperly Adjusted Clutch Cable or Linkage. 4 Inspect Transmission Shift Linkage (Manual) Loose or Worn Shifting Linkage. 5 Inspect Clutch Disc Broken, Missing or Weak Clutch Disc Springs. 6 Inspect Clu 1 Inspect Transmission Modulator(Automatic) Modulator Leaking Fluid into Vacuum System. 2 Inspect Transmission(Capacity) Fluid Level Incorrect. 3 Inspect Transmission Fluid Type Contaminated Transmission Fluid. 4 Inspect Transmission Filter (A/T) Clogged or Dirty Transmission Filter. 5 Inspect Automatic Transmission Internal Transmission Problems.tch Disc Broken, Missing or Worn Pressure Plate Diaphragm Fingers.

Sep 02, 2009 | Chevrolet 2500 Cars & Trucks

4 Answers

96 chevy blazer 3rd gear and overdrive slipping


i got a 1996 chev. blazer s-s10 4.3 engine 4x4.problem i got is i got 1st 2nd & overdrive & reverse but no 3rd gear what should i do

Jun 30, 2009 | 1996 Chevrolet Blazer

1 Answer

I have a 1986 Chevy S-10 Blazer with an Automatic Transmission that will not go into any forward gears in 2 wheel or 4 wheel drive, but will go into reverse. The engine is fine. The transmission fluid is...


Clarification please... Do you mean by "go into" as the shift linkage will not move into the forward ranges or that the vehicle will not move forward? Both are possible scenarios but very different. Let me hear clarification for sending a test procedure for either one.

Mar 26, 2009 | 1986 Chevrolet S-10 Blazer

1 Answer

My 96 chevy blazer 4wd will not work?


check clutch slave cylinder and or adjustment

Jan 16, 2009 | 1999 Chevrolet Blazer

1 Answer

1991 chevy s10 pickup won't shift into park


Has anyone tried lubricating & or adjusting linkages/cable?

Nov 30, 2008 | 1993 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...