Question about Ford Cars & Trucks

1 Answer

2002 Ford Escape XLS 3.0 DOHC 24v pulleys and belt coming out of the valve cover is?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 372 Answers

Camshaft drive pulleys

Posted on Mar 29, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: misfire on cylinder 6 on a 2002 ford escape 3.0 6 cylinder DOHC

the back side is from front(passenger side) of engine 1,2,3
front side is 4,5,6

Posted on Mar 17, 2009

  • 21 Answers

SOURCE: Focus timing belt replacement.

This is a very very easy timing belt setup. first off you have to remove the valve cover. Then you have to remove the serp belt. Then remove anything thats in your way of the front cover. after you remove the crank pulley re-install the crank bolt. DO NOT LOSEN THE BOLT FOR THE TENSIONER!!!! now spin the crankshaft until the sproket aligns with the timing mark. now at this point the two camshafts should be aligned. now there is a special tool from ford that holds the cam shafts in place. all it is is a 1/4" peice of metal that goes on the left side of the cam shafts to hold them into place. if you mark the cams you wont need the tool. or if you can find something to fit in the left side of the cams that will work too. anyways after that its just the same steps in reverse. very easy to do.

Posted on Aug 31, 2009

moparownr
  • 667 Answers

SOURCE: 2002 Ford Escort ZX2 serpinten belt routing & tensioner pulley

go to www.gates.com on the lower right hand side under popular topics, click on timing belts, then on the left hand side click Parts Locator and Interchange, enter your cars info and the first page that comes up will show you a camera icon for a pic of how your belt is routed. The tensioner pulley is the one mounted on a silver arm, usually at the top. Hope this helps let me know.

Posted on Sep 22, 2009

  • 1757 Answers

SOURCE: serpentine belt diagram

CLICK on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/2002/make/ford/model/escape/2002_ford_escape_drive_belt_routing_diagram.htm

Posted on Mar 09, 2010

  • 22 Answers

SOURCE: i need a routing diagram for the serpentine belt

c6eb5b9.jpg

Here ya go.

Posted on Jun 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to check the transaxle fluid level on a 2002 ford escape xls v6


Locate and remove speed sensor. level and fill piont

Nov 17, 2012 | 2002 Ford Escape

Tip

Setting Timing Without 3 So Called SPECIAL TOOLS Needed


1997-2000 Ford Contour 2.0L DOHC Camshaft Set up For timing Belt Replacement.most Instructions Call For 3 Different Special Tools No NeedFORD UPGRADED TIMING PULLEYS AND TENTIONERS In a UPGRADE KIT
Remove Valve Cover And TOP Timing Belt Cover CUT BELT OFF, Go to Rear of CAMSHAFTS (OppositeSPROCKETS) Look and you will see SLOTS at the end of Each CAM they are CUT ECCENTRICALLY . Use a Piece of Sturdy FLAT STOCK HARD STEAL (STRAIGHT) Turn CAMS one at a TIME Until they are EVEN With COVER GASKET SURFACE of Head, ALIGN BOTH Cams this Way Insert FLAT STOCK IN SLOTS So CAMS Don't Spring Back, And you Have VALVE TRAIN TIMED PERFECTLY, #1 Spark Plug OUT Bar Over to TDC WOODRUF KEY Should be Pointed Straight UP. This Is ALL there is to IT. Proceed with Timing Cover Removals and front Mount, REPLACE ALL PULLEYS AS A KIT (SOLD AS KIT) Install Timing Belt Set Tensioner According to KIT Instructions ans this will Illuminate All Special Tools SAID to be NEEDED for this Procedure, (( REMOVE FLAT STOCK AT CAMSHAFT ENDS AFTER BELT IS TIGHTENED.Install New Valve Cover Gasket #1 Spark Plug and Job is Done. Cuts 1 Hour 15 Minutes off Flat Rate

on Dec 31, 2009 | Ford Contour Cars & Trucks

1 Answer

Need a diagram for a serpentine belt for a 2002 ford escape 24 v DOHC V6


I did find your manual but it did not detail the serpentine belt. Here it is just FYI.
2002 Ford Escape Owners Manual

Mar 28, 2011 | 2002 Ford Escape

1 Answer

Serpintine belt diagram


what engine? Please rate if it helps

3.L v6

snorkelbobby_26.gif Item Part Number Description 1 3A733 Power steering pump pulley 2 8620 Drive belt 3 2E884 A/C clutch pulley 4 6316 Crankshaft pulley 5 6B209 Drive belt tensioner 6 10344 Generator pulley


2.0L Zetec 4 cyl with A/C

snorkelbobby_27.gif Item Part Number Description 1 10344 Generator pulley 2 19A216 Belt idler pulley 3 3A733 Power steering pump pulley 4 6C301 Drive belt 5 2E884 A/C clutch pulley 6 6B320 Crankshaft pulley 7 8509 Water pump pulley 8 6A228 Drive belt tensioner

Jan 12, 2011 | 2002 Ford Escape

1 Answer

Hi, I am looking for a timing belt diagram for a 1998 2.5ltr Subaru Outback or can you tell me which timing marks on the sprockets line up to the encasing.


Timing Belt Cover, Belt & Sprockets Removal & Installation 2.5L Engine To Remove:
  1. Remove the drive belts.
  2. Remove the A/C compressor drive belt tensioner. Timing belt & cover DOHC exploded view subaru-03-25-6470.gif

  3. Remove the crankshaft pulley.
  4. Remove the mounting bolts and left timing belt cover.
  5. Remove the mounting bolts and right timing belt cover.
  6. Remove the mounting bolts and front timing belt cover.
  7. Vehicles W/ M/T: Remove the timing belt guide.
  8. Ensure that the timing belt rotation arrows are still visible. If the marks are worn off, place new rotation marks on the belt. Timing belt alignment marks DOHC subaru-03-25-6472.gif

  9. Turn the crankshaft using a breaker bar and special adapter socket on the crankshaft. Align the timing mark on the crankshaft sprocket (1), left intake sprocket (2), left exhaust sprocket (3), right intake sprocket (4) and right exhaust sprocket (5) with the notches in cylinder block and timing belt cover.
  10. Paint alignment marks on the timing belt at the crankshaft and camshaft sprockets timing marks. CAUTION
    Do not turn the camshaft sprockets with the timing belt removed. The valves heads will contact each other causing the valve stems to bend.
  11. Remove the lower right idler pulley.
  12. Remove the timing belt.
  13. Remove the upper right idler pulley.
  14. Remove the lower left (toothed) idler pulley.
  15. Remove the belt tensioner.
  16. Hold the sprocket and remove the left intake and exhaust camshafts.
  17. Hold the sprocket and remove the right intake and exhaust camshafts.
  18. Remove the crankshaft sprocket.
To Install:
  1. Install the crankshaft sprocket.
  2. Hold the sprocket and install the right intake and exhaust camshafts with the mounting bolts. Tighten 58 ft-lb (78 Nm).
  3. Hold the sprocket and install the left intake and exhaust camshafts with the mounting bolts. Tighten 58 ft-lb (78 Nm).
  4. Reset the automatic belt tensioner as follows:
    • Remove the mounting bolt and belt tensioner. NOTE: Do not exceed more than 2,205 lb. (9,807 N).
    • Place the belt tensioner on a press. Press the adjuster rod down gradually (using more than 3 minutes) 66- lb (165 N) or more until the adjuster rod is aligned with the stop pin hole in the cylinder.
    • Insert a 0.08 in (2 mm) diameter pin or hex wrench into the pin hole to lock the adjuster rod.
    • Install the automatic belt tension adjuster with the mounting bolt. Tighten 18 ft-lb (25 Nm).
  5. Install the lower left (toothed) idler pulley. Tighten 29 ft-lb (39 Nm).
  6. Install the upper right idler pulley with the mounting bolt. Tighten 29 ft-lb (39 Nm). Crankshaft sprocket and oil pump cover alignment marks 2.5L DOHC subaru-03-25-4890.gif

  7. Align the timing mark on the crankshaft sprocket with the mark on the oil pump cover. Timing belt alignment marks DOHC subaru-03-25-6472.gif

  8. Align the single timing mark on the right exhaust camshaft sprocket with the notch on the timing belt cover.
  9. When the single timing mark on the right exhaust camshaft sprocket is aligned with the notch on the timing belt cover, ensure that the double lines on the intake camshaft and exhaust camshaft sprockets are aligned.
  10. Align the single timing mark on the left exhaust camshaft sprocket with the notch on the timing belt cover by turning the sprocket counter clockwise (viewed from front of engine).
  11. Ensure that the double lines on the intake camshaft and exhaust camshaft sprockets are aligned when the single timing mark on the left exhaust camshaft sprocket is aligned with the notch on the timing belt cover. CAUTION
    • The camshafts can be rotated independently causing the valves heads to contact each other resulting in bent valve stems.
    • When the timing belt is removed the camshafts will turn to the lowest cam lobe position by the force of the valve springs. Before installing the timing belt the 4 camshafts are in the lowest lift position (valves closed).
    • When the camshafts are rotated to install the timing belts, # 2 intake and # 4 exhaust cam lobes of the left camshafts are held to push their corresponding valves down. In this position, these valves are held in the open position. Right camshafts are held so their cam lobes do not push the valves down.
    • The left camshafts must be rotated from the lowest lobe position to the position where the timing belt can be installed at the smallest possible angle in order to prevent intake and exhaust valve contact. Camshaft sprockets rotation subaru-03-25-6473.gif

    • Do not turn the camshafts in the direction shown in the illustration because the valves will open at the same time and contact each other.
    CAUTION
    If the timing belt alignment is off the mark buy more than 3 teeth, the valves and pistons may have contact.
    Timing belt alignment marks DOHC subaru-03-25-6472.gif

  12. Align the timing marks on the belt with the marks on the sprockets in the numerical order shown in the illustration.
  13. Install the lower right idler pulley with the mounting bolt. Tighten 29 ft-lb (39 Nm).
  14. Ensure that the timing mark alignment is correct and remove the tensioner stop pin.
  15. Vehicles W/ M/T: Install the timing belt guide and temporarily tighten the mounting bolts.
  16. Vehicles W/ M/T: Measure the clearance between the guide and timing belt. The clearance should measure 0.039 ± 0.020 in (1.0 ± 0.5 mm).
  17. Vehicles W/ M/T: Tighten the guide bolts 7.2 ft-lb (9.8 Nm).
  18. Install and secure the front timing belt cover with the mounting bolts.
  19. Install and secure the right timing belt cover with the mounting bolts.
  20. Install and secure the left timing belt cover with the mounting bolts.
  21. Install the crankshaft pulley.
  22. Install the A/C compressor drive belt tensioner.
  23. Install the drive belts.
prev.gif next.gif

Sep 30, 2010 | Subaru Outback Cars & Trucks

3 Answers

I need a belt routing diagram for a 2000 ford taurus 24v dohc engine. Know where I can find one on the web? (No sticker under the hood. And I was dumb enough not to pay attention when I took it off.)


OK, one doesn't need a belt routing diagram to reinstall a new belt.

Just route the belt so that one by one you put the ribbed part of the belt up against the ribbed pulleys, and the smooth part of hte belt up against the smooth pulleys. Do this until one arrives at the tensioner and release tension with a breaker bar to put the belt on the final tensioner pulley.

Check that the tensioner has enough spring load for the belt to maintain the right friction against all of the serpentine pulleys.

That's all there is to it.

Sep 09, 2010 | 2000 Ford Taurus

2 Answers

Serpentine belt diagram 2002 ford escape picture of serpentine belt pattern


CLICK on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/2002/make/ford/model/escape/2002_ford_escape_drive_belt_routing_diagram.htm

Feb 27, 2010 | 2002 Ford Escape

1 Answer

How many milles change timing belt ford escape 2002


On a 2.0L (DOHC) Vin B replace the belt at 120,000 miles.
Warning: This is an interference engine. If the belt breaks serious engine damage will occur.

Nov 29, 2009 | 2002 Ford Escape

2 Answers

How to replace power steering pump on 2002 ford escape


Take a picture of it before you take it apart so you know where everything goes.
1.Take belt off
2. Unbolt any bracket that the power steering pump is bolted too.( only if you have to unbolt a bracket)
3. Disconnect lines from steering pump
4. After replacing power steering pump fill with Auto. trans fluid.
5. After filling start car and turn wheel left and right a few times this will get the air out of the system and recheck fluid level.

Apr 22, 2009 | 2002 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5608 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...