Question about Nissan Tiida
Most likely the wire between the button and the overdrive solenoid is apart, or insulation off so it is grounding, or bad connections at switch, or at solinoid. Or power supply to the switch is bad or connection loose, or possible the switch itself is bad.
Posted on Apr 02, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The door handle has a c clip behinde it that you can not see.Goto a auto parts store and thay will have a cheep tool to help you.(you need a special tool for this.
The WINDOW CRANK handle has a 'c-clip' behind it. The door opening handle trim is held in by either a screw behind a plastic flap that will pop out(behind the lever)or it is held in at four points by plastic tabs (two on top and two on the bottom)that can be undone carefully with a screwdriver or the like. When this plastic trim is removed the door panel should come off.
Be aware that there are plastic clips (back side of the panel) on the perimeter of the panel that hold it in as well.
the tweeter panel just pops out look on the bottom of the door for screws and around the door handle and you will have to pop your window and door lock controls out and the reflector on the door pops out and there is two screws there then al you have is the clips behind the door they make tools for it but a flat tip screwdriver will be fine just get the tip close to the clip and pull it out .
1. Remove window crank (it has a kind of 'bent wire' c-clamp, which holds it onto the window crank shaft).
2. Pry upwards the top plastic cover to the arm rest (this is a plastic coated foam rubber piece, on which you rest your arm).
3. Remover the two now visible screws which fasten the arm rest onto the door.
4. Remove the one screw fastening the inside door handle.
5. With a blunt tool, gently hit the inside door handle in a forward direction (towards the door hinge). This will release the door handle from the door.
6. Pry between the door panel and the door, to unsnap the snaps holding the door panel in place.
7. Finally, lift door panel out and up to remove it from door.
Posted on Feb 09, 2009
I just had the same problem,also door locks would not engage when shifted out of park. Had problem for a week now all is ok didnt do anything
Posted on Apr 08, 2010
SOURCE: Warning light indicator
Hello, My car is nissan tiida 2007. I recently noticed that there is a yellow colored engine shape warning indicator in the dashboard. What does this mean
Posted on Nov 06, 2011
SOURCE: i have a 2006 is250 lexus push button start and it only starts sometimes....radio, lights, nav everything works but it won't crank....takes 3-4 times before it cranks and it doesn't happen eve
The first thing you want to check for is the brake signal,without this signal it will not crank,this is the easy one make sure you get brake light,the second is to have the starter tested by a direct method,this gives the indication of the health of the starter
Posted on Mar 23, 2012
Tips for a great answer:
Jun 17, 2016 | Nissan Tiida Cars & Trucks
Feb 25, 2016 | Nissan Cars & Trucks
May 12, 2014 | 2007 Nissan Tiida 1.6
Jan 21, 2014 | 1994 Nissan Altima
Dec 06, 2013 | 2007 Nissan Tiida 1.6
Jan 27, 2013 | 2007 Nissan Tiida 1.6
Nov 29, 2012 | Nissan Tiida Cars & Trucks
Apr 06, 2012 | 2007 Nissan Tiida 1.6
43 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: