Question about 2005 Nissan Murano

1 Answer

2005 Nissan murano awd v-6 intermittent engine cut out around 50 mph with very little response when the accelerator pedal is depressed

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Nissan Master
  • 531 Answers

Sounds like it's in limp mode

check engine light on?

any trouble codes stored in the ecu / ecm? free scan at the local autozone or advance auto parts store for that

Posted on Mar 28, 2015

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: nissan murano 2005 sl keyless entry remote programing

Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source

Posted on Aug 06, 2008

countrysi248
  • 443 Answers

SOURCE: STUTTERS DURING ACCELERATION

throttle position sensor .. this lets the computer know just where your foot is on the gas .. It gets worn out in that position because that is where it is used the most. I would check it first then go from there... they are priced reasonable .. always start with the least expensive first then go from there. thanks Jerry holler if you need more

Posted on Feb 05, 2009

  • 1 Answer

SOURCE: 2005 nissan murano sl, with rattling sound when accelerating

I recently experienced the same symptom with my '05 Murano and it was not a fuel problem. The dealer listed the cause as dry axle splines and replaced both front drive shaft assy's. Note that this was done as warranty with no cost incurred by me.

Posted on Jun 18, 2009

  • 840 Answers

SOURCE: vibration after 50 mph, and when accelerateing

Welcome to fixya the best thing to do is check the rims for imperfections and slight bents that causes the vibrations at that speed go to www.collisionrepairadvice.com to get a wheel repair company to look at.

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel pump relay located for 2005 nissan murano awd


its behind your fuse panel but upwards. You can see it if you get your head down and kiss the pedals. Your definitly gonna have to do some dash diving though it you decide to mess with it.

Its under the dash on the drivers side, all the way to the left. Its light blue and a pain in the a@$ to get to

Dec 21, 2016 | 2005 Nissan Murano

1 Answer

Where is cylinder 1 on a 2005 Nissan Murano AWD?




google search werks for me! isn't teh interwebs wonderful!?!

same generation engine 3.5L is only other thing you confirm

Mar 18, 2015 | 2005 Nissan Murano

1 Answer

How should i use my awd on my murano 2005? awd lock its that mean that its on and how much speed can i go please sombody


AWD is computer controlled in your 05 Murano. AWD lock is for low speeds under 10 MPH or something like that. I've had my 05 Murano since 05 and never used AWD lock. Between VDC and AWD I've never had any problem getting around. My salesmen told me it was for low speed/towing...I never tow so I've never used it.

Dec 31, 2010 | 2005 Nissan Murano

1 Answer

I have a 2001 nissan pathfinder 4w. The OBD system-readiness status: Says catalytic converters, NOT READY; oxygen sensors, NOT READY; evaporative system, NOT READY. So did not pass inspection, I was told...


You have to re-set the obd via using Nissan's approved drive-cycle which is;

1. Start the engine when the engine coolant

temperature gauge needle points to C. Allow

the engine to idle until the gauge needle

points between the C and H (normal operating

temperature).

2. Accelerate the vehicle to 55 MPH (88

km/h), then quickly release the accelerator

pedal completely and keep it released for at

least 6 seconds.

3. Quickly depress the accelerator pedal for a

moment, then drive the vehicle at a speed

of 53 to 60 MPH (86 to 96 km/h) for at least

5 minutes.

4. Stop the vehicle.

5. Accelerate the vehicle to 35 MPH (55 km/h)

and maintain the speed for 20 seconds.

6. Repeat steps 4 through 5 at least 3 times.

7. Accelerate the vehicle to 55 MPH (88 km/h)

and maintain the speed for at least 3 minutes.

8. Stop the vehicle and turn the engine off.

9. Repeat steps 1 through 8 at least one more

time.

If step 1 through 7 is interrupted, repeat the

preceding step. Any safe driving mode is acceptable

between steps. Do not stop the engine

until step 7 is completed. If you cannot or

do not want to perform the driving pattern, a
NISSAN dealer can conduct it for you.

Nov 15, 2009 | 2001 Nissan Frontier Crew Cab

1 Answer

MR2 Acceleration issue


check the air intake tube to the engine for a crack between the MAF sensor and intake of the engine, pull it off and bend it around. look at the bottom carefully.

Aug 13, 2009 | Toyota MR2 Cars & Trucks

2 Answers

Intermittent power loss after accelerating hard


Sounds like a fuel delivery problem! Try filter first (cheapest), then the pump
Hope this helps, Henry

Oct 17, 2008 | Nissan 240SX Cars & Trucks

1 Answer

Intermittent power loss after accelerating hard


hi what is your car have no codes come up if not do a fault reading see if it has stored any as tps [throttle position sensor ] map sensors and airflow sensors will cause this problem as will a few others it can be expensive guessing yates210456

Oct 17, 2008 | 2003 Nissan Se R

2 Answers

Reset check engine light


First of all, you should'nt do this unless you know what the problem is.. or what tripped it. I had this problem when my husband and I were replacing a head unit and disconnected the old head unit, a/c and other stuff then turn the car on. This made the light flash. The first time we took it in and got charged $50 to reset it. The second time we did this procedure and it worked.

ECU Resetting Procedures

Timing is extremely critical. If it is NOT DONE within the specify time, the ECU will not reset and the Check Engine Light (CEL) will continue to remain ON.
A stop watch or an analog clock with a second’s needle will be useful.

Reset Check Engine Light Procedures

1. Confirm that accelerator pedal is fully released, turn ignition switch “ON” and wait 3 seconds.
2. Repeat the following steps (2a and 2b) procedures quickly five times within 5 seconds.
2a. Fully depress the accelerator pedal (HARD).
2b. Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the CEL starts blinking.
4. Fully release the accelerator pedal (while the CEL is still blinking)
5. Wait about 10 seconds.
6. Fully depress the accelerator pedal and keep it for more than 10 seconds.
7. Fully release the accelerator pedal (The CEL light will continue to blink).
8. Turn ignition switch to “OFF” position and now you can start the car. The CEL light should be gone.

If the CEL light continues to remain ON, repeat the above steps. Timing is EXTREMELY critical to resetting the ECU.

-Christine

May 15, 2008 | 2007 Nissan Murano SE

Not finding what you are looking for?
2005 Nissan Murano Logo

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...