Question about 1993 Nissan Altima
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.
Posted on Apr 06, 2009
Crankshaft and Camshaft Position Sensors
Camshaft Position Sensor
Engine timing is determined from the relationship between the crankshaft and camshaft. This relationship is maintained by a timing chain or timing belt. The Engine Management System does not control engine timing but it does monitor the relative position and speed of these shafts by monitoring signals generated by sensors. The Engine Management System (EMS) uses signals generated by the camshaft position sensor to synchronize fuel injection to the valve sequence and for the on-board diagnostic procedure for misfire detection. The EMS energizes the injector at or near the time the intake valve opens. For misfire diagnosis, the EMS compares the number of camshaft sensor reference pulses and the number of crankshaft position sensor reference pulses received. If the EMS receives an incorrect number of pulses Diagnostic Trouble Codes (DTC’s) should be stored in the EMS.
If the camshaft position sensor or circuit is faulty most engines will start. Some engine management systems will then default to a pre-programmed injector firing sequence. All injectors may be energized simultaneously or all of the injectors on one bank may be energized at the same time. If the CMP data is required for misfire detection and reliable CMP data is not present misfire detection would probably be suspended.
Related Symptoms The following symptoms can be caused by an intermittent wiring connection or faulty signal to the EMS:
In addition the EMS uses minute variations in the CKP sensor data to determine engine misfire. The EMS uses this information in conjunction with the camshaft position sensor to perform misfire diagnostics.
Related Symptoms: No Start/Intermittent Start Condition – Can be caused by a faulty crankshaft position sensor due to loose connections, bad grounds, high resistance in the circuit, or opens in the circuit
Posted on Jun 23, 2009
You are incorrect sir. There is a very good Youtube video showing you exactly where it is that is how I changed mine. The Crankshaft is located behind the engine block below and around from the cam sensor which is easly spotted looking at the engine. The crankshaft is in a difficult spot but once you figure out where it is it's easy...ish hope this helps
Posted on Dec 10, 2009
Tips for a great answer:
Dec 18, 2016 | Nissan Cars & Trucks
Mar 26, 2015 | 1993 Nissan Altima
Aug 02, 2011 | 2003 Nissan Altima
May 12, 2010 | 1993 Nissan Altima
Apr 03, 2010 | 1993 Nissan Altima
Jan 17, 2010 | 1993 Nissan Altima
Nov 30, 2009 | 1993 Nissan Altima
Nov 05, 2009 | 1993 Nissan Altima
May 11, 2009 | 2008 Nissan Altima
Dec 18, 2008 | 2005 Nissan Altima
136 people viewed this question
Usually answered in minutes!