Question about 2004 Nissan Murano

1 Answer

Nissan murano 2004 low beam is about 4 feet away i need it at least 10-12 feet away ,how I raise it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Nissan Master
  • 531 Answers

Http://www.nicoclub.com/FSM/Murano/2004/lt.pdf

page LT-33 for Xenon type headlights

OR

page LT-63 for Conventional halogen type headlights

credit for Greg over at nicoclub dot com for his resource to what stealership mechanics use!

Posted on Mar 28, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10865 Answers

SOURCE: TYPE AND CAPACITY OF OIL FOR MY NISSAN MURANO 2004

hello. with a new filter, add 4 1/4 quarts of oil, US measure. The type is any good quality oil, API grade SG/SH. Go to page 249 in your owner manual for more details, here is the manual in case you do not have one http://www.courtesyparts.com/pdf/2004-Nissan-Murano.pdf

please mark my answer as very helpful. thanks. Joe

Posted on Mar 31, 2010

insanegtp
  • 112 Answers

SOURCE: 2004 Nissan Murano How do you clear maintenance light after oil change?

press maintanence button until you see engine oil, then hold trip/reset button... :)

Posted on Oct 03, 2008

  • 1 Answer

SOURCE: 2004 Nissan Murano, back door can't open

I had a similar problem with a sienna and sometimes the cable ( inside the door) between the handle and the latch gets stuck in the sleeve. Kind of like the brake cable on a bike.
take the panel off by removing all the screws you can see on the panel and pull the panel off. There will be plastic pins holding it. Some of them may pop off and some will break off.
Drip oil down the sleeve so the cable slides freely. I used bike chain oil. Do not use WD40. This is **** and will not work for very long. Try the handles a few times before you put the panel back.

Posted on Mar 03, 2009

TwinTurboZ
  • 78 Answers

SOURCE: Headlight Aiming/Adjustment

On the sides of the Radiator cross member. Look straight down. Should be a silver colored phillips head screw

Posted on May 15, 2009

  • 13 Answers

SOURCE: Toyota avensis 2002 1798cc, headlights beam is low need to raise

you need to bring it to a garage with a headlight alignment machine to pass an MOT. ensure the headlight position switch (on the right hand side of the dash) is set to "0"

Posted on Jul 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i adjust the head lights in or out on a 2004 dodge stratus---or can i?


If by in or out you mean make the beam pattern move closer or farther away from the vehicle, then yes you can. There are adjustment screws (usually 2) on each headlamp assembly. One raises and lowers the headlamp. This will move the beam closer to (down) or further from (up) the vehicle. The other will adjust the beam from left to right. The screw at the top (or bottom) is for the vertical and the screw on the side is for horizontal. The easiest way to adjust the headlamps correctly is to, at night, go to a location where you can park about 50 feet away from a blank wall. Turn on the low beam headlamps. In order to "properly" adjust the lamps, the left side headlamp's main beam should cast is "ring" on the wall at about the centerline of the car (left-to-right adjustment), with the bottom of the beam just reaching the ground (vertical adjustment). The right side headlamp should be adjusted to shine along the right edge of the vehicle (where the white edge line would be) at the 50 foot mark (left-to-right) and the height should be the same as the left headlamp - beam just touching the ground. Many people make the mistake of pointing them straight down the road. This causes "overspray" into the oncoming lanes and blinds oncoming motorists. I'm sure you've experienced the annoyance of someone coming toward you with their lights right in your eyes. That is caused by misadjustment. If you get the low means right, the high beams will work well for approximately 200-300 feet down the road, which, unless you are night racing, is more than enough distance to see well to drive.

Dec 10, 2015 | 2004 Dodge Stratus

1 Answer

How to set hibeam and low beam in a nissan murano?


http://www.nicoclub.com/FSM/Murano/2004/lt.pdf

page 33 for xenon headlights

or

page 63 for conventional halogen headlights

Mar 28, 2015 | Nissan Murano Cars & Trucks

1 Answer

How to reset the low tire indicator on a 2004 nissan murano


some time ago while researching how these tyre indicators worked I came across a web site that had this sort of information available . So I suggest that a surf of the web under tyre indicators will provide the answer for you.

Jun 11, 2014 | 2004 Nissan Murano

1 Answer

How many kilogram of oil engineneeds a Nissan murano 2004?


In the United States we don't use Kilograms as a measure of oil we use Quarts. Your country uses Litres wherever you are! THe MUrano uses 5 quarts of oil...you convert it to litres and you get .95 litres = one quart. Just use 5 quarts and all will be OK.

Jan 02, 2013 | 2004 Nissan Murano

1 Answer

What is a driveline services for a 2004 Nissan Murano


the CVT transmission should not need service until 100k miles.

Additionally Nissan extended the service of all Muranos with CVT transmissiont to 120k miles.

you can check the forum nissanmurano.org for any Murano issues. I am not affiliated with that site but a regular user

May 10, 2010 | 2004 Nissan Murano

1 Answer

TYPE AND CAPACITY OF OIL FOR MY NISSAN MURANO 2004


hello. with a new filter, add 4 1/4 quarts of oil, US measure. The type is any good quality oil, API grade SG/SH. Go to page 249 in your owner manual for more details, here is the manual in case you do not have one http://www.courtesyparts.com/pdf/2004-Nissan-Murano.pdf

please mark my answer as very helpful. thanks. Joe

Mar 31, 2010 | 2004 Nissan Murano

1 Answer

I need to replace and then adjust the headlights on my 2000 Chrysler 300M. How do I replace the headlights, then adjust them.


Park your vehicle on level ground with the headlights near a garage door or wall. A good distance is 2-3 feet away from the wall or door. The location must be perfectly level and flat at a distance of 10 to 25 feet away from the door or wall.
Switch on the low headlight beams and mark the horizontal and vertical centerlines of each headlight beams on the wall using masking tape. This will mark the center of each beam with a +. The marking will tell you where exactly the headlight beams should be centered from a distance.

Move the vehicle back about 10 to 25 feet away from the garage door or the wall.

Keep the headlights on the low beam setting.
Use the markings you made on the wall or garage door to, check where the light shines and see if the centerlines still match up with the masking tape marks. If the centerlines of the two beams do not align with the tape marks, you can adjust one or both sides as needed.

Make the necessary adjustments with the lights still on while watching the light beams on the wall and your marks.
Turning the top adjusting screws in a clockwise direction will raise the beam while counterclockwise turn will lower it.

Turning the side adjuster screws will adjust the lights to the left or right.

Continue the adjustments until the center of the light beams are aligned with the tape marks. Then adjust the vertical alignment of both beams slightly below the marks on the wall. This will assure that the lights are tilted slightly downward so they won’t blind approaching motorist.

The will align bot lights, the high and low sine both are connected to the same headlight!!

Nov 18, 2009 | 2000 Chrysler 300M

2 Answers

How do I adjust the headlights to see further down the road on my 2004 Chrysler Pacifica?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 12, 2009 | 2004 Chrysler Pacifica

1 Answer

LIGHT ON???


it is your low tire warning light have your air pressure checked
hope this helps and please rate me

Aug 20, 2008 | 2004 Nissan Murano

1 Answer

Headlight adjustment


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Jun 15, 2008 | 2004 Nissan Altima

Not finding what you are looking for?
2004 Nissan Murano Logo

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...