Question about Cars & Trucks

1 Answer

Need the torque specs for the starter mounting bolts - 13mm

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

About 50 foot pounds. Haven't ever put a torque wrench t o this.

Posted on Mar 28, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 Dodge Intrepid intake manifold torque specs top & bottom is for 3.5 V6


Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Jun 24, 2016 | 2003 Dodge Intrepid

1 Answer

What is the torque specs for brake calipers on a ford explorer sport front calipers


  1. Torque Specs For F250 Caliper Bolts - Diesel Forum - TheDieselStop.com

    www.thedieselstop.com > ... > 1999-2007 General Questions Jan 13, 2009 - 3 posts - ‎1 author
    Does any one know what the caliper bolts torque specs are? ... Disc brake caliper pin bolts - Excursion, F-250/F-350 with Ford and Dana axle ... Torque specs for front brakes
    5 posts
    Mar 12, 2009
    05 F250 brake torque specs please
    6 posts
    Aug 22, 2007
    Brake caliper torque specs
    5 posts
    Jul 14, 2007
    Front brake Caliper Bolt Torque
    6 posts
    Apr 25, 2005
    More results from www.thedieselstop.com

Jul 11, 2015 | 1998 Ford Explorer

1 Answer

85 Peugeot 505 Automatic Standard I need to replace the bolts that mount the starter to the transmission. However I don't have the previous bolts. Anyone know the specs on these bolts? Thanks


Does the starter have a threaded end? Meaning, do the nuts tighten themselves into the starter or does a nut and washer fasten it to the transmission? Regardless...I can assure you the nuts are a metric size....likely a 13mm head.

Dec 03, 2013 | Cars & Trucks

1 Answer

Need torque specs for power steering pump bolts on a 99 ford taurus


just pull them up tight ,i assume you mean the pump mounting bolts 13mm spanner ,just a nip is all thats required say around 20lbs

Oct 28, 2012 | 2000 Ford Taurus

1 Answer

What is the arm rocker? Torque bolts specs. For a 95 accord non v.tec f22b2 engine


i just pull them up with a rachet and one grunt ,they are only 13mm headed bolts so around 35 but i never use a torque wrench to be honest ,not even for head bolts on my beloved jag .

Mar 05, 2012 | 1995 Honda Accord

1 Answer

Replacing a starter in a sebring 2006


All of the nuts and bolts are metric on it. It helps to use a 13mm swivel socket on the starter bolts but you can use a wrench if you need to. Also, a 7/8 open end wrench for the 02 sensor, or an 02 sensor socket.


Let me give you the steps for the starter and also the front engine mount bracket. You don't have to remove the entire mount, just the bracket




REMOVAL

  1. Open Hood.
  2. Disconnect the negative battery cable.
  3. Raise vehicle and support.
  4. Disconnect the electrical connector from the 02 sensor.



2009-10-31_143231_starter1.gif




  • Remove the 02 sensor from the exhaust manifold .
  • Remove the front mount through bolt.
  • Remove the front mount bracket from engine block.







  • 2009-10-31_143306_starter2.gif



    Remove the battery cable from starter.




    2009-10-31_143343_starter3.gif



    1. Remove the lower starter bolt and remove starter.

    INSTALLATION

    1. Install starter to transmission.
    2. Start the upper starter bolt.
    3. Start the lower bolt and snug it so that the starter will not move.
    4. Remove the upper bolt.
    5. Connect the battery cable and torque nut to 8.5 Nm (75 in. lbs.).
    6. Install the front mount bracket and check heat shield location.
    7. Install bolt the upper bolt and torque bolt to 54 Nm (40 ft. lbs.)
    8. Install the lower and torque bolt to 54 Nm (40 ft. lbs.)
    9. Install the front mount through bolt and torque bolt to 61 Nm (45 ft.. lbs.)
    10. Install the 02 sensor and torque to 27 Nm (20 ft. lbs.)
    11. Lower vehicle.
    12. Connect the negative battery cable.




    FRONT MOUNT

    REMOVAL

    1. Raise vehicle.




    2009-10-31_143650_mount1.gif



    1. Remove front mount to bracket horizontal through bolt (Fig. 87).
    2. Loosen the rear mount through bolt.
    3. Remove front mount vertical bolts (Fig. 87).
    4. Remove front mount and separate the starter heat shield.

    INSTALLATION

    1. Position front mount on lower radiator crossmember.
    2. Loose install front mount to bracket through bolt.
    3. Install front mount vertical bolts. Tighten bolts to 61 Nm (45 ft. lbs.) . (Fig. 87).NOTE: Be sure the weight of the engine is static and in rest position. this for a 2.7 v6

    Jan 15, 2012 | 2006 Chrysler Sebring

    1 Answer

    How do I replace the starter in an 86 vw cabriolet?


    If it's a 5 speed, you will need to disconnect the battery at the positive terminal. Jack the car up and support with jack stands. You will need another jack to sit under the oil pan, due to the fact that when removing the starter, the bolts through the starter go thru the front motor mount. Disconnect the large wire from the starter, usally a 13mm nut, and unplug the smaller wire. Remove the upper and lower bolts going thru the starter, usally a 17mm bolt head, or an allen head bolt. Remove the starter, you may have to jack up or down the motor to get the starter bolts started into the front mount. If it's an automatic, the starter is mounted between the engine and the firewall. The 5 speed starter is between the engine and radiator.

    Mar 11, 2010 | 1986 Volkswagen Cabriolet

    2 Answers

    Brake job torque spec


    Caliper bolt 25 ft lbs/ caliper bracket bolt 79.6 ft lbs

    Nov 13, 2009 | 2005 Honda Civic

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    20 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...