Question about Cars & Trucks

Open Question

Genie silent max 1000 is completely dead

Door went up it got jamed on motor now is completely dead

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My power window will not work is there a fuse that controls all windows


There is a fuse for windows. However, if only one window is non operational, there is either a short specifically affecting that window or the motor for the window is broken.

Dec 08, 2015 | 1996 Jeep Grand Cherokee

1 Answer

Blower not working at all. Fuses & relays ok. Aircon cuts in when fan is turned on but no air from vents. Need to know what colour wire supplies power to the blower before I assume the motor is faulty


the blower is silent.????????? yes, sounds matter !
ON HIGH TOO? (fan speed max)????
or makes normal sounds, but does not blow.
1 or the other.?

the blower if dead silent can be hot wired (blows now?) (costs zero to do)
or using any voltmeter made. measure for 12vdc on the 2 pin
to motor, fan on high. (costs $10 for tool at walfart)
if 12vdc there, (across the 2 pins) then the fan is bad.
of 0v, the controls are dead.
the fan on most cars. on high, bypass the fan speed resistor block.
what you dont have is the schematic,
its at 2 places (usa ,min)
alldata.com
and suzukipitstoppus. (real fsm book)

2000 GV, data, below.... it takes all of 10sec to look.
all answers, USA cars, as this is a USA forum.
i click HVAC for you.
as you can see the switch is grounded at red circle.
and with fan on high ground (0v) is applied to the motor low pin
and if the relay is hot, (2 fuse good) the output of relay b/w wire
will be at 12vdc, if not the relay is bad.(fuses good)
cant be more simple. same from 89-2000 after that things get harder, (controls) your car has a motor driven mode damper
that is why i asked the sounds questions. as it too can block the air flow. (with a perfectly running fan)


25677825-i2v1dhik2lesr4tboqpiuxwr-4-0.jpg

May 03, 2015 | 2000 Suzuki Grand Vitara

1 Answer

Why wont my 2005 mitsubishi outlander start?


This is James at Auto.Repairs
I ask please to rate any and all answers if they have helped you in any way please do so as for this helps me advance to the next level.
Thank you.

Could you please be more specific such as noises it may have made before and after, did it just go dead silent or just putter to a crawl. Have you tried anything such as starting fluid to see if it would start back up. Any tests been done.

Sep 08, 2014 | 2005 Mitsubishi Outlander

1 Answer

AUDIO FUSE


you have a wire Conn so were from the switch to the battery

Apr 22, 2017 | 2005 Kia Sorento

1 Answer

I HAVE A 1997 JEEP CHEROKEE AND THE DRIVERS SIDE WINDOW MOTOR WENT COMPLETELY DEAD. HOW DO I KNOW IF IT NEEDS A NEW MOTOR?


If all the other windows work...that will eliminate the fuses and relays.
You can check the window switch...but the easiest way to check it and the motor at the same time is to remove the door panel to get to motor.

Using a multimeter, check for voltage at the power plug of the motor.
If you toggle switch and you get voltage...switch is good.
Reconnect power to motor and try moving window.

This will determine if you need motor or a window regulator...or both.

Hope this helps...

Aug 13, 2011 | 1997 Jeep Grand Cherokee

2 Answers

How do I program my Jaguar XJR garage door opener?


Sorry, the process is simple but too lengthy to post here.

Goto homelink.com

They make the system and have very complete instructions you can download.

PLEASE NOTE: MOST but not ALL Brands / models of opener will work with this system.

Jun 30, 2009 | 2006 Jaguar XJ8

1 Answer

Driver side window down and won't come up??


When you push the button to raise the window, do you hear it humming or clicking, or is it dead silent? If it's silent, the motor isn't even trying to raise the window. That's either a blown fuse, a dead window regulator, or a dead window switch. If you hear it clicking or making noises, but not coming up, it's either the regulator is messed up (but not dead), or the window has come off it's guide tracks and can't raise up.

Aug 30, 2008 | 2006 Nissan Frontier

1 Answer

Programming the garage door opener


Homelink Garage Door Opener Programming Procedure:

The procedure described below was successfully applied to a 2005 Jaguar S-Type.

To begin with, several attempts were made using the programming instructions contained in my Jaguars owners manual. Though the procedure described in the owners manual was straight-forward and understandable, I was unsuccessful in getting the vehicles remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the Rolling Code feature.

To begin with, be sure to clear previous codes on your Jaguars garage door opener by first turning (rotating) the ignition key to the I position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle buttons red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguars garage door opener console buttons. Choose which button on your Jaguars remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguars opener button. The red light on your Jaguars center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.

Part two: Now it is time to utilize the Learn function on your Genie garage door opener. Press the Learn button on your Genie garage door opener. The red LED adjacent to the Learn button will begin to flash. You now have 30 seconds in which to program your Jaguars opener button. Using the same button you just used in the part 1 procedure, press and hold the same button for several seconds. As before, your Jaguars red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center buttons red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguars remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguars remote button confirms to the Genies rolling code that your Jaguars signal is legitimate and is to be trusted from then on.

Jun 06, 2008 | 2003 Jaguar XJ-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...