Question about 2004 GMC Canyon

1 Answer

Passenger rear park lamp doesn't work.

It is a two way bulb that I have replaced with a working bulb from another socket. the socket is clean and the contacts are proper position. The fuses have been checked except for the park lamp relay. Being that the other park lamps work, I didn't think that was the problem. So, what can I do to further troubleshoot this problem?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 5,316 Answers

Both park lamps should be powered by the same wire, so follow wire from non-working light until you find a break or bad connector.

Posted on May 05, 2015

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
roniecon
  • 6826 Answers

SOURCE: Driver low beam head light stoped working,

There is a left head light relay,and a right head light relay,check those relays.

Posted on Nov 19, 2009

johnjohn2
  • 5763 Answers

SOURCE: I have a 2003 GMC

the first thing would be to test for power and ground at the wires going to the sockets, the most common reason for this is the sockets go bad inside.this is a complete unit, the main connector is where you would check for power first then go on to socket, most of the time the connector for the main power feed goes bad, it has a connector for all the wiring and then splits all wires to there location inside headlight asm. again testing with a testlight would be very helpful i think you will find a bad socket for each light out or the main connector on the headlight asm is bad. good luck. have a good day.

Posted on Mar 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2004 chev Express box van and my tail lights wont work every blinker works just not the lights both sides replaced bulbs still nothing


Fuse Usage 1 Climate Control 2 (HVAC) 2 Compass 3 Ignition Switch, Theft Deterrent System Module (PK3) 4 Upfitter Courtesy Lamps 5 Climate Control 1 (HVAC) 6 Empty 7 Instrument Panel Cluster 8 Audio System, Chime 9 Auxiliary Park Lamp 10 Auxiliary Trailer Back-up Lamps 11 Remote Function Actuator, Tire Pressure Monitor (TPM) 12 Climate Control (HVAC) Controls 13 Trailer Park Lamps 14 Front Park Lamps 15 Taillamps, Back-up Lamps 16 Empty 17 Steering Wheel Sensor 18 Outside Rearview Mirror Switch 19 Empty 20 Empty 21 Rear Defogger 22 Outside Rearview Mirror Heater 23 Empty 24 Empty 25 Cargo Door Unlock 26 Rear Door Lock 27 Front Door Lock 28 Rear Passenger Door Unlock 29 Upfitter Park Lamps 30 Front Passenger Door Unlock 31 Driver Door Unlock 32 Airbag System, Automatic Occupant Sensing (AOS) System 33 Right Rear Park Lamp 34 Left Rear Park Lamp 35 Upfitter Auxiliary 2 (J-Case) 36 Upfitter Auxiliary 1 (J-Case) 37 Rear Blower (J-Case) 38 Empty (J-Case) 39 Run (High Current Micro) 40 Park Lamps (High Current Micro) 41 Empty (Mini Micro) 42 Upfitter Auxiliary 2 (High Current ISO Relay) 43 Retained Accessory Power (RAP) (High Current Micro) 44 Rear Defogger (High Current Micro) chevrolet-express-fuse-box-floor-console-fuse-block-247x300-3m55w415sdhfmumhyuzqkab2-3-0.jpg

Jul 27, 2017 | Cars & Trucks

1 Answer

Front passenger and rear drivers side parking lights not working on 2003 Ford Focus. What could be the reason?


check bulbs. if bulbs are good check bulb sockets. I would suspect one or the other are bad.

Apr 13, 2013 | 2003 Ford Focus

1 Answer

2006 VOLVO FRONT LEFT PARKING LIGHT


Has the bulb socket been tested to see if 12 volts is present with lights on? If it is replace the bulb, if that doesn't cure the issue replace the socket. Also make sure the socket has a good ground.

Mar 13, 2012 | 2006 Volvo V70

1 Answer

My taillight (rear - passenger side) is not working - the other one on the driver side is. I change both bulbs in the non-working on (bulb #1157) and the tail light is still not working. What do I do...


Check the bulb socket. They get really hot and heat can cause the wires to melt solder holding them in place. If you have a test light, probe the socket pins for power,(light switch on). If none on either pin, then probe the wires an inch or so back from the socket. If wire(s) have power replace socket. If not, and even if you find power on the pins but the lamp doesn't work, then also check for a bad or loose ground wire.

Aug 21, 2011 | Subaru Legacy Cars & Trucks

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

1 Answer

Passenger side fog lamp wont turn on


Check the bulb, socket interface, clean contact points. IF you have a test light or ohmeter, check for power to the socket. If unpowered, check the fuse, if powered check bulb element, and socket condition.

Mar 21, 2010 | 2005 Subaru Outback

1 Answer

I have a 1988 Ford Thunderbird Turbo Coupe. The rear brake lights (which has a dual filament bulb) does not light up when the headlights are on but lights up when I hit the brakes... Fuses have been...


You have no power when the parking lamps are on. Do the front parking lamps work? If the front parking lamps work then you have an issue with the rear wiring. Use a test light to verify you do not have power at the sockets.

Nov 02, 2009 | 1988 Ford Thunderbird

1 Answer

How do I replace rear passenger side brake light on a 2007 Hyundai Sonata


There is an 'access panel' in the trunk liner right behind the tail lamp assy. Loosen wingnut to release cover. Now you have access to the bulb sockets. Be sure you replace the bulb with the same type (dual filament).. otherwise you could cause a short circuit between the 'parking lamp' and the 'brake lamp' circuits.

Sep 06, 2009 | 2006 Hyundai Sonata

Not finding what you are looking for?
2004 GMC Canyon Logo

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...