Question about 2008 Buick Lucerne CX

1 Answer

Cruise control wont engage after restarting vehicle

The cruise control on my car works when we first start the car up, but if i shut the engine off, and then restart it again, cruise control wont engage. The light turns on for maybe 1/10th of a second, then shuts off. Cruise control will then only work normally once the car has been turned off for a few hours. Turning off traction control didn't help.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 78 Answers

The fact that the light comes on is a good indication that the electronics are working, the most common problem is a vacumn leak. This can be a damaged or cracked vacumn line, a bad check valve, or the dump switch on the brake pedal

Posted on Mar 31, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 1997 Plymouth Voyager 6Cyl. Had clockspring repaired at dealer. Cruise control light goes on in dashboard but no cruise?


cruise controls are operated by
brake switch
VSS auto or clutch pedal -manual
tacho
control switch,
ECM
cruise control will not engage if the engine rpms are too low , vehicle speed is to slow
VSS unit is faulty (wiring)
switch is not making full contact
any one dropping out will cancel the control engagement

Sep 28, 2016 | Plymouth Cars & Trucks

1 Answer

Where is the fuse for the cruise control on 2010 gmc pickup?


There is no fuse for Cruise Control , power is supplied by the BCM !
The body control module (BCM) monitors the signal circuit of the cruise control switches. The BCM relays the cruise control switch status to the engine control module (ECM) via the GMLAN serial data circuit. The ECM uses the status of the cruise control switch to determine when to capture and maintain the vehicle speed. The ECM monitors the vehicle speed signal circuit in order to determine the desired vehicle speed. The ECM uses the throttle actuator control (TAC) motor in order to maintain the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Descriptionfor the 4.3L engine or Throttle Actuator Control (TAC) System Description for the 4.8L, 5.3L, 6.0L, 6.2L or 7.0L engines.
Voltage is supplied to the cruise control switch via the steering wheel control switch reference voltage circuit supplied by the BCM. The cruise control function switches are arranged in a resistive ladder design, with each cruise control function switch having a different resistance value. The BCM detects a specific voltage value that is associated with the cruise control function switch being activated. When the normally open cruise control on/off switch is turned ON, the switch closes and the BCM supplies a ground to the cruise control switch ON indicator circuit as it becomes illuminated. The BCM sends a GMLAN serial data message to the ECM indicating that the on/off switch is active. Similarly, when the normally open + RES switch or the normally open - SET switch are pressed, the switch closes and the BCM detects the predetermined voltage signal on the cruise control set/coast and resume/accel switch signal circuit. The BCM sends a GMLAN serial data message to the ECM indicating that the + RES switch or the - SET switch is active. To engage the Cruise Control System, ensure that the vehicle speed is above 40.2 km/h (25 mph), turn the cruise On/Off switch ON and momentarily press the - SET switch. The ECM will engage the Cruise Control System and record the vehicle speed. The ECM sends a GMLAN serial data message to the driver information center (DIC) in order to illuminate the CRUISE SET TO ### message. The ECM sends a GMLAN serial data message to the instrument panel cluster (IPC) in order to illuminate the Cruise Engaged indicator in the IPC.
If you don't know this I suggest you take your vehicle to the dealer or a ASE certified repair shop .

Apr 07, 2016 | 2010 GMC Sierra 1500

1 Answer

Cruise control won't engage


cruise controls are governed by 5 settings and sensors
one is engine rpms
vehicle road speed ,( manual transmission will not activate under 20 klms /hr
brake pedal switch
clutch pedal switch ( VSS if auto)
off/on switch control
any one of these not lined up will not allow the cruise control to work

Oct 13, 2015 | 2013 GMC Sierra 2500HD

1 Answer

Where is the fuse for cruise control on a 2003 envoy


It is HVAC 1fuse #39 in the rear fuse block ,this powers the on/off switch for cruise control ! Fuse Block - Rear Beneath the left rear seat. What engine does it have ? 4.2 L or 5.3 l There is no vacuum involved in the operation of the cruise control ! Your vehicle has electronic throttle control .
Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at vehicle speeds above 40 km/h (25 mph). Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the Cruise Control System:
?€¢
The powertrain control module (PCM)


?€¢
The On/Off switch


?€¢
The Resume/Accel switch


?€¢
The Set/Coast switch


?€¢
The TCC brake switch


?€¢
The stop lamp switch


?€¢
The throttle actuator control (TAC) motor


?€¢
The vehicle speed sensor


Cruise Control Engaged
The cruise control system will engage and adjust the vehicle speed based on the activation of the following cruise control switches:
?€¢
On/Off


?€¢
Resume/Accel.


?€¢
Set/Coast

The cruise control switches are located on the multifunction/turn signal lever.
The powertrain control module (PCM) monitors the signal circuits of the cruise control switches in order to determine when to capture and maintain the selected vehicle speed. The PCM uses the throttle actuator control (TAC) module motor in order to control the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Description in Engine Controls - 4.2 L.
Ignition positive voltage is supplied from the 10 ampere HVAC 1 fuse to the cruise control switch via the ignition 3 voltage circuit. When the normally open cruise control On/Off switch is turned On, the switch closes and the PCM detects a high signal voltage on the cruise control on switch signal circuit. When the normally open Set/Coast switch is pressed, the switch closes and the PCM detects a high signal voltage on the cruise control set/coast switch signal circuit. To engage the cruise control system, turn the On/Off switch On and momentarily press the Set/Coast switch. The PCM will confirm that the cruise control enable criteria has been achieved. The PCM will engage the cruise control system and record the selected vehicle speed. The PCM sends a class 2 message to the instrument panel cluster in order to illuminate the cruise control indicator. Pressing the accelerator pedal, while the cruise control system is engaged, will allow the driver to override the cruise control system in order to accelerate the vehicle beyond the current set vehicle speed. When the accelerator pedal is released, the vehicle will decelerate and resume the current set vehicle speed. The driver can also override the current set vehicle speed via the Set/Coast switch and the Resume/Accel switch. When the cruise control system is engaged, pressing and holding the Set/Coast switch will allow the vehicle to decelerate from the current set vehicle speed without deactivating the cruise control system. When the Set/Coast switch is released, the PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily pressing the Set/Coast switch will allow the vehicle to decelerate at 1.6 km/h (1 mph) increments for each time that the Set/Coast is momentarily pressed, with a minimum vehicle speed of 37 km/h (23 mph). When the normally open Resume/Accel switch is activated, the switch closes and the PCM detects a high signal voltage on the cruise control resume/accel switch signal circuit. Activating and holding the Resume/Accel switch, when the cruise control system is engaged, will allow the vehicle to accelerate to a greater vehicle speed than the current set vehicle speed. When the Resume/Accel switch is released, the PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily activating the Resume/Accel switch will allow the vehicle to accelerate at 1.6 km/h (1 mph) increments for each time that the Resume/Accel switch is momentarily activated, with the maximum acceleration total of 16 km/h (10 mph) over the current set vehicle speed . Momentarily activating the Resume/Accel switch, after the cruise control system has been disengaged by pressing the brake pedal, will recall the previous set vehicle speed that is recorded in the PCM.

Sep 11, 2015 | Cars & Trucks

1 Answer

Cruise control not working


cruise controls are dependent on the following sensors all working together
brake sensor
clutch sensor
auto--vehicle speed sensor
rpm's sensor
fuse for the cruise control
cruise control switch either or all not working will stop the cruise control from engaging
road speed at which you can engage the cruise control has to be above a reset speed before it will cut in and work

Sep 05, 2015 | 2009 Chevrolet Chevrolet Equinox LS

4 Answers

2005 Chevy trailblazer ext problems 1. Cruise will not set.worked last on 4/12/15 2. While checking fuses for CC problemdome lights stopped working, but worked fine before checking fuses. PLEASE HELP!


Bummer deal! This may be a way to tell you some tail lights are burnt out. Some cruise controls have a fuse in a second location.
The fuse is not in right or is blown. Check with a new fuse. Hope this helps. ...gc http://www.auto-tune-up-and-repair-options.com/

Apr 20, 2015 | 2005 Chevrolet Trailblazer Ext

1 Answer

Envoy 2005 XL Cruise control not working


Your dealership should have seen any underlying codes. Most Cruise controls I've worked on are used on the vehicles vacuum. that is where i would start, because on a grade your engine uses more vacuum pressure thus taking from some where else.

Jan 12, 2012 | GMC Envoy Cars & Trucks

1 Answer

Cruise Control


there is a vacuum silinoid that controls the vacuum being applied to the cruise control actuator it might be defective

Jul 29, 2008 | 1999 Oldsmobile Intrigue

Not finding what you are looking for?
2008 Buick Lucerne CX Logo

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...