Question about 2007 Chevrolet Chevrolet Equinox LT

Open Question

Rear wheel bearing on 2007 chevy ecquinox - 2007 Chevrolet Chevrolet Equinox LT

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mrgreenz
  • 962 Answers

SOURCE: (How do I replace rear bearings) chevy sliverado RWD

Check to see if the drum is hotter than normal. If the bearings are bad, you have to lift the truck and remove the axle. Remove the wheel drum until you get to the axle. They to remove the axle, you have to open the rear end Spider gear ***** at the middle. They have a half moon wedge or a clip you have to remove. They you pull out the axle.Replace the bearing grease it and seal it. Then put it back in the reverse order. Sounds simple but it is not that simple. Takes work

Posted on Jan 11, 2009

Ad
  • 24 Answers

SOURCE: how do I replace the rear wheel bearing in a 2000

I am sorry to tell you this, but you will have to take the Truck to a Rear End repair shop to do this. If you are very mechanically inclined and have all the specific tools like a slide hammer, bearing puller, bearing installation tool, etc. If you have tools like this, then I would get yourself the car manual. To replace the bearings you will have to remove the axles.

Posted on Oct 06, 2009

  • 972 Answers

SOURCE: how to replace rear wheel bearing on 2003 chevy

its not hard but you do have to remove diff cover and then take out spider shaft to remove clips that hold axle. then remove bearing with slide hammer or puller. if bearings are bad so is the axle because its part of the bearing

Posted on Jun 20, 2010

duane_wong
  • 6826 Answers

SOURCE: How do you change the

Axle Shaft Bearing & Seal Removal & Installation To Remove:

  1. Raise and safely support the vehicle.
  2. Remove the axle shaft.
  3. If replacing only the seal, remove the seal using a suitable seal removal tool.
  4. If replacing the seal and bearing on the 8.6 inch axle, install the slide hammer and adapter behind the bearing and pull out the bearing and seal together.
  5. If replacing the rear axle shaft seal and the bearing on the 9.75 inch axle, install the J 29712 or equivalent bearing puller into the axle housing behind the axle bearing.
  6. Remove the axle shaft seal and the bearing by tightening the nut on the J 29712 bearing puller.
Use a slide hammer, bearing puller and adapter to remove the old axle bearing 88457g81.gif

To Install:
  1. Install the axle shaft bearing using a suitable size driver. Drive the bearing into the housing until the tool bottoms against the tube.
  2. Lubricate the seal lip and install the seal with a suitable seal driver. Make sure the seal is fully seated in the axle tube.
  3. Install the axle shaft.
  4. Fill the rear axle with the correct lubricant.
  5. Lower the vehicle.
prev.gif next.gif

Posted on Oct 18, 2010

canwoodjc
  • 3301 Answers

SOURCE: 2007 Chevy Equinox 4 wheel

could be wheel bearings, or just tire noise

Posted on Sep 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear bearings


As I said, all wheel bearings are replaceable. Remove the bearing cover, remove the split pin, undo the castleated nut, remove the hub. Push the bearing out from the rear. There is usually a small ring of bearing seat visible from the rear. I used to use a large socket with the extension bar and a good sized hammer with the hub on a block of wood.

Nov 24, 2015 | 2007 Kia Sorento 4x4

1 Answer

How do I replace the rear end wheel bearing on driver side? It's a 2007 Crown Victoria. I was driving it to work one day and the back end locked up. It will drive forward but it makes the most horrific...


#1. A wheel bearing should not lock up the rear end. #2. Sounds like you have a far worse problem, probably in the differential. To replace the wheel bearing you need to remove the diff cover, take out the spider gear pin remove the locking c clip and remove the axle. Obviously the left rear wheel and rotor and caliper have to be removed as well. then the bearing ,which is pressed into the housing needs to be removed. If the bearing is that bad the axle will need to be replaced as well.

Feb 20, 2015 | 2007 Ford Crown Victoria

1 Answer

How many rear wheel bearings are there on chevy equinox 2005


There are two rear Wheel hub on a chevy equinox. You also have a rear differential containing bearings.

Sep 13, 2014 | 2005 Chevrolet Equinox

1 Answer

How do i remove a seized up rear wheel bearing on a 2 wheel drive 2007 Chrysler Pacifica Touring


How do you know its the bearings.

Aussuming the car is front wheel drive, what happens when you try to drive it? Does it drag the wheel? There is a chance it may break it free since you've gone over it with a slege hammer.

Mar 12, 2014 | 2007 Chrysler Pacifica Touring

1 Answer

How to check rear wheel bearings 2007 jeep compass


block front wheels and jack up rear slightly off the ground, keeping your body parts out of harms way you can grab and shake tires, if they move back and forth or in and out even slightly it is time for bearing work

Nov 23, 2012 | 2007 Jeep Compass 2.4

1 Answer

How to replace rear wheel bearing on 2003 chevy s10 4x4 zr2? My skill level is basic, I do the oil changes and tune-ups on my truck but not to much more. It is a ''Do-ItYourSelf'' jobs or is the maybe...


its not hard but you do have to remove diff cover and then take out spider shaft to remove clips that hold axle. then remove bearing with slide hammer or puller. if bearings are bad so is the axle because its part of the bearing

Jun 20, 2010 | 2003 Chevrolet S-10

Not finding what you are looking for?
2007 Chevrolet Chevrolet Equinox LT Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...