Question about Daewoo Nubira

1 Answer

I have a daweoo nubira my clutch pedal keeps going soft it is coming up and down but no preasure what is the problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Daewoo Master
  • 45,599 Answers

Probably a clutch master cylinder problem with bad piston seals
take it to a brake specialist shop but be prepared for a new master cyl.

Posted on Mar 28, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Low / Soft Clutch Pedal, 1995 Rodeo 2W 2.6L

my rodeo had the same problem i corrected it by bleeding the slave cylinder. and is located on the driver side on the gearbox you will find it if you follow the line from the master cylinder down to the gearbox and if that helps but happens again it might have to be replaced.

Posted on Dec 29, 2008

  • 186 Answers

SOURCE: Clutch Pedal Very Soft

Air in the system. The shave is between the engine and trans and even a small leak won't show up. Look in the rubber piece on trans with a light and see if you see any fluid. If you see any then the slave is starting to fail.

Posted on Aug 03, 2009

  • 1149 Answers

SOURCE: clutch pedal goes to floor no preasure filled and

Hi:
If you have bled the system, you are down to either having a bad clutch master cylinder, or a bad clutch slave cylinder. You could eliminate the slave cylinder by removing the line and capping it off, and if you have a firm pressure on the clutch pedal ( don;'t try to push it down, just check for pressure!) then your slave cylinder is bad. If you cap off the line, and bleed the system, and the pedal still has no pressure, then your clutch master cylinder is bad!

Posted on Apr 15, 2010

  • 14585 Answers

SOURCE: My 1993 toyota pickup won't go into gear.

there is still air in the system, keep pumping it will eventually come out. if it has a bleeder try that

Posted on Jun 15, 2010

  • 5 Answers

SOURCE: Soft clutch pedal

well depends on how much milage on the clutch..I would start with clutch master and slave see if that helps because u have to replace any how.....good luck

Posted on Jun 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nubira fuel


did you check your intake fuel sensor that could also reslut in high petrol consumption

Mar 04, 2014 | Cars & Trucks

1 Answer

Clutch pedal goes to floor no preasure filled and bled slave cyl same result


Hi:
If you have bled the system, you are down to either having a bad clutch master cylinder, or a bad clutch slave cylinder. You could eliminate the slave cylinder by removing the line and capping it off, and if you have a firm pressure on the clutch pedal ( don;'t try to push it down, just check for pressure!) then your slave cylinder is bad. If you cap off the line, and bleed the system, and the pedal still has no pressure, then your clutch master cylinder is bad!

Apr 15, 2010 | 2004 Chevrolet Cavalier

2 Answers

Replaced Clutch, master cylinder and slave cylinder on my 85 F250 diesel. The truck shifts ok when it is cold, once it warms up it wont shift using the clutch. you have to use RPMs to make it shift. I...


these are very hard to bleed, also check your fire wall for damage where the clutch master bolts up. another thing is take a good look at the clutch pedal asm, the frame sometimes wears and cracks so you loose a little pedal travel.another thing is a bad preasure plate,spring breaks on plate,

Mar 10, 2010 | 1985 Ford F 250

1 Answer

When I release the clutch pedal, the clutch bites/engages immediately. There is hardly any travel and the pedal feels slack. Will I need a new clutch?


No it just needs adjusting. Don't adjust it very tight adjust until the preasure comes on the pedal about half way up or where you are comfortable with it. Cheer's

Sep 22, 2009 | 2000 Volkswagen Golf

1 Answer

Daewoo Nubira 2002 (Purge Valve) replacement question How To


where can i find the Purge Control Valve in my daweoo 2002 nubira

Apr 03, 2009 | 2002 Daewoo Nubira

1 Answer

Clutch problems on a 1999 daewoo nubira


It's your slave cylinder most likely. Assuming you don't have any leaks in the system. Your pedal is connected to a hydraulic cylinder. It should be up under the dash. Follow the pedal up until you see it.

Mar 28, 2009 | 1999 Daewoo Nubira

1 Answer

Timing diagram for 2002 daweoo nubira


try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 20, 2009 | 2000 Daewoo Nubira

2 Answers

Clutch bleeding


Try opening bleeder screw on slave cylinder and let it GRAVITY BLEED, just open clutch mater and fill with fluid and then open slave cylinder bleeder screw and let it gravity bleed( run out by itself) When it does close bleeder screw and you should get pressure.(make sure master doesn't run out of fluid during this preocess).If pedal not good enough bleed as usual. PUMP PEDAL ABOUT 6 time then hold down to the floor using wrench open slave bleed screw and close back up with pedal still being held DOWN. Repeat until fluid comes out with out air.However if all this doesn't work, YOU WILL NEED TO REPLACE CLUTCH MATER CYLINDER. Conatct if you need more help and Good Luck. Thanks for using FIX YA

Jan 12, 2009 | 2001 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...