Question about Toyota HiAce

Open Question

Axle seal is leaking is is it the outer seal that needs replacing or is there an inner seal as well

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Rear Axle Removal

if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

Posted on May 30, 2008

  • 883 Answers

SOURCE: Rear Axle Removal

rate me solved...this is all I can find...

figure 1

d164665.jpg

figure 2
c12dde8.jpg

defeae4.jpg

Posted on Jun 27, 2008

warlock61
  • 659 Answers

SOURCE: Rear Axle Leak

if it is the seal, you will have to remove the caliper and rotor, remove the differential cover and remove the bolt and pin inside the diff carrier housing. push in the axle and remove the axle clip and pull out the axle use a seal puller or prybar to remove seal reverse the steps to assemble

Posted on Dec 10, 2008

  • 51 Answers

SOURCE: Left rear axle seal is leaking differental oil.

ok then here is the procedure  1 take off the axle nut
2 on the lower control arm you will find a large nut and bolt i belive the nut is a 21mm and the bolt side is an 18mm. this bolt is the one at the knuckle near the brakes. remove it
3 you will need to pull the knuckle out of the way or a helper to pull the knuckle out of the way so you can slip the axle out of the knuckle.( its a tight fit but there is room to slip it out.)
4 use a pry bar to pop the axle free of the diff. hosing its held in by a spring clip make sure the clip comes out with the axle if it gets stuck inside you will have to fish it out.
5 use a pry bar or screwdriver to pry seal out of housing then use a flat object that contacts the entire rim of the new seal so it can evenly be installed with out getting smashed and tap it in with a hammer. ( a good trick here is to use some grease and pack it into the new seal where the spring is this will prevent the spring from being shocked out of the seal during instalation . the spring keeps tension on the rubber in the seal so it stays tight to the shaft it is sealing.)
6 then revers the above steps. also make sure you are using the right gear lube it will most likely be 75w-140 but make sure you check your owners manual will tell you if it doesnt say on the diff cover. you can cause a lot of damage if you put in the wrong thing. and make sure  you feel the axle spring clip snap into place.
as a note there are two types of axle seals that are used on these so if the new seal looks different than the old seal then the folliowing will be important to you.the seals on these have been redesigned so if you axle has what looks like a cup or dust cover pressed onto the shaft where it goes into the diff the new style does not use this and it will prevent the axle form going in all the way so the spring clip will not lock in and you will have a leak. so you will have to remove it and install the axle without it.

Posted on Mar 22, 2009

  • 335 Answers

SOURCE: REAR AXLE SEAL LEAKING ONTO BRAKE SHOES NEED INSTRUCTIONS ON HOW TO FIX

Jack up vehicle and support on stands. Remove wheels. Remove differential cover . Locate and remove lock pin that holds cross shaft in. Slide cross shaft out. Push axle inward to release axle c clip. Remove axle and pry out old seal. Install new seal with proper tool.Add some lube to the seal lip to aid axle intallation. Revese removal procedure. This is for a "c" type axle.
Another type has 4 nuts attaching a retainer plate to the backing plate behind the axle flange. In this case the 4 nuts are removed and the axle will come out. This may require a little effort. I think that you have a "c" type axle in your vehicle. Hope this helps. Moe

Posted on Apr 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove outer half shaft seal on MF 2203 we think it's fitted with MF 165 axle


You have to remove the inner hub first. I suggest you buy the shaft. If you don't get it right, both sides leak. Were I live, that seal is half the cost of a new axle.

Aug 07, 2016 | Cars & Trucks

1 Answer

How do i change the front axle on a 2004 impala


You will need a large socket to fit the nut on the end of the CV axle shaft. You will also need a breaker bar to remove this nut. You will need a torque wrench capable of achieving the correct torque when replacing the nut on the replacement shaft. You will need a relatively heavy (3-pound) hammer and a pry bar to remove the axle shaft from the transmission housing. You should break the axle nut loose prior to raising the vehicle off the ground as it is very tight and may not come loose easily once raised. If you use an impact wrench then the need to do this before raising the vehicle is not as great. You need to raise the vehicle on jack stand(s). Remove the wheel from the side you are replacing. Remove the brake caliper and rotor assembly as well. Remove the axle nut. The axle must be pulled free of the hub spline by pushing it out backwards. This is not usually possible without either (1) separating the lower ball joint from the lower control arm, or (2) unbolting the lower control arm assembly from the subframe and pulling it outward and to the side.
Be careful when pushing and pulling on the axle shaft. The outer CV joint is fixed, but the inner joint can be pulled out too far and become separated. This will make removal much more difficult. Once you have freed the outer CV joint from the hub, then you need to use the prybar and hammer to tap the inner joint out of the transaxle. It snaps in place and will take a few attempts to achieve. Be careful if trying to pry on the transaxle housing as it is cast metal and can break easily. Once you have the inner joint free you can remove the shaft. There may be some transmission fluid leak from the seal when you remove the shaft. Insert the new shaft into the transaxle. Push it in to snap it into place. You can pull back about an inch or two to help get the force necessary to pop it in, but again be careful not to overextend the inner joint. Once the inner joint is in place, slide the outer joint back through the hub splines. Reconnect the ball joint/lower control arm. Replace the axle nut (use the one supplied with the new shaft. Torque to proper specifications. Replace the rotor/caliper/wheel.

Dec 26, 2014 | 2004 Chevrolet Impala

2 Answers

Replace front seal transmission


remove cv axle or axles and replace inner and outer seals replace cv axles when out if boots are ripped

Sep 19, 2013 | Lexus Cars & Trucks

1 Answer

How do i get the rear hub off to change the seal? I have the outer nut and bearing off, cant get inner bearing to come loose.


check to see if you have another nut inside holding the inner bearing inside the axle tube, if so remove it and the bearing, pull the axle and replace the axle seal.

Aug 02, 2010 | 1986 Ford F 250

1 Answer

How to change the rear bearings in my 1997 grand cherokee limited


YOU HAVE TO SAFELY RAISE SUPPORT VECHICLE MAKE SURE ITS ON A SOLID LEVEL GROUND.THEN YOU REMOVE THE WHEELS THE BRAKE DRUM OR DISC.THEN YOU REMOVE THE NUTS THAT ATTACH THE OUTER SEAL RETAINER AND BRAKE BACKING PLATETO THE AXLE SHAFT TUBE.DISCARD THE NUTS.REMOVE AXLE SHAFT FROM HOUSING.WITH AN AXLE PULLER ATTACHED TO A SLIDE HAMMER.DISCARD INNER AXLE SEALPOSITION THE AXLE SHAFT IN A VISE.REMOVE THE RETAINING RING BY DRILLING A 1/4 HOLE ABOUT 3/4 OF THE WAY THROUGH THE RING. THEN USING A COLD CHISEL OVER THE HOLE.SPLIT THE RING.REMOVE THE BEARING WITH A ARBOR PRESS DISCARD THE SEAL AND REMOVE THE RETAINER PLATE.TO INSTALL - CLEAN THEN APPLY A THIN COATING OF WHEEL BEARING LUBRICANT TO THE BEARING AND SEAL CONTACT SURFACES APPLY WHEEL BEARING LUBRICANT TO THE LIPS OF THE REPLACEMENT INNER AND OUTER SEALS.INSTALL THE INNER SEAL WITH THE OPEN END OF THE SEAL FACING INWARD ENSURE IT IS COMPLETELY SEATED.INSTALL THE RETAINER PLATE AND THE OUTER SEAL ON THE SHAFT.ENSURE THE OPEN END OF THE SEAL FACES TOWARD THE AXLE SHAFT BEARING.PACK THE REPLACEMENT BEARING WITH WHEEL BEARING LUBRICANT AND POSITION ON THE AXLE SHAFT PRESS INTO PLACE.PRESS A REPLACEMENT BEARING RETAINER ON THE AXLE SHAFT AGAINST THE BEARING.INSTALL THE AXLE INTO THE AXLE TUBE.POSITION AND ALIGN THE SEAL RETAINER AND BRAKE SUPPORT PLATE AND INSTALL REPLACEMENT ATTACHING NUTS.TIGHTEN NUTS TO 32 FT LBS.INSTALL BRAKE ASSEMBLY WHEELS LOWER VECHICLE. YOU SAID REAR BEARINGS IF THIS WHAT YOU MEANT.I HOPE THIS CAN HELP.

Apr 12, 2010 | 1997 Jeep Grand Cherokee

1 Answer

I had my inner and outer CV boot on the right replaced as it was torn. Could the mechanics have disrupted my transmission. Immediately afterwards my transmission fluid is all over my, and then my in-laws,...


the axle shaft seal might have been damaged upon dissambly or reassembly or the attaching clip might have not seated properly causing the axle to not seat properly in the transmission also the axle seal surface if it was a replacement shaft might not be large enough to seal properly.

Jan 02, 2010 | 2003 Toyota ECHO

2 Answers

1994 buick roadmaster, oil leaking out of right rear axle, checked brake fluid is full, could it be differential oil leak @ end of axle??


If what you see leaking is very oily and does not evaporate, likely it is an axle seal. If there are no leaks in the brake system, that's the only thing back there that can leak. If the axle bearing is going away, it can damage the seal so make sure you look for small shiny metal flakes behind the seal when you replace it or you will be doing the job again very soon. Can't remember...that IS rear wheel drive right?

Dec 01, 2009 | 1994 Buick Roadmaster

3 Answers

I have an oil leak between the drivers rear axel and the tire. What parts do I need to look into replacing?


You should be ok replacing the outer seal but check for bearing play or fautly outer wheel bearing before you disassemble. If to much lateral movement in axle shaft it will take out your new seal rather quickley.

Sep 25, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Lower ball joints and leaking boots on my 2004 2.7 AWD santa fe hyundai how much work


Labor Skill
Level
Mfg.
Warranty
Standard Axle Shaft Replace Front Axle Intermediate Shaft B 0.9 1.3 Notes NOTE To R&R Inner Shaft Bearing and/or Dust Seal, Add B 0.1 0.1 Notes Axle Assembly One Side B 0.6 1.0 Notes NOTE To R&R Outer Joint and/or Boot, Add Each B 0.0 0.5 Notes To R&R Inner Joint and/or Boot, Add Each B 0.0 0.5 Notes To R&R Axle Shaft Seals, Add Each B 0.0 0.2 Notes Rear Axle One Side B 1.2 1.7 Notes NOTE To R&R Outer Joint and/or Boot, Add Each B 0.0 0.5 Notes To R&R Inner Joint and/or Boot, Add Each B 0.0 0.5 Notes

Apr 20, 2009 | 2004 Hyundai Santa Fe

1 Answer

Grease leak toyota 4runner 1996


You need to disconnect the rear wheel cylinder brake line and pull off the rear backing plate, via the 4 bolts that are visible after you remove the brake shoes. One the backing plate is loose, take it down, out of the way, and pull the axle shaft straight out. You will need several parts from a Toyota Dealer, and a machine shop to press off the old bearings and seals, and to press on the new bearings and seals. Go to the dealer & tell them your problem, we do this job once-twice a week; a common issue. The only seal that you can change yourself is the axle tube "outer" seal, you will see it when you pull out the shaft. But, this seal is not the cause of your leak. The inner seal on the shaft is worn. You will also need to replace the oily brake shoes, too. Hope this helps. A FIxYa rating would be appreciated.

Feb 26, 2009 | 1998 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...