Question about Acura Integra

Open Question

Timed to raise my 1995 acura integra higher because everytime you go over a pothole some of the lug nuts come off so I need step by step instructions on how to do this project also I need to know how to do the hub cap removal and putting it back on

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: lost my hub cap key

dealer

Posted on Jan 04, 2009

bunnydawg
  • 5158 Answers

SOURCE: 1990 Sentra How it remove and replace lug studs on front wheel

there is a large nut that holds that hub on. Remove the cotter pin and the cap from the bolt... remove the bolt and the hub comes off.

Robert

Posted on Feb 27, 2009

  • 38 Answers

SOURCE: Instructions to replace sheared off lugs / studs - 1997 Chevy

You need to remove the wheel of course. It depends on if the silverado is like the 1997 GMC 3/4 ton K2500 4x4. If so, then the easiest way is to remove the hub with the rotor because on the GMC the lug bolts go through both making them one unit. I just changed out the lugs on a 1997 GMC as mentioned above while replacing the ABS / wheel bearing hub assembly in which I had found to be the easiest procedure. Place the unit on the bench and look to locate the back of the lug nuts so you can see if there is anything else you may want to do to make things easier and then drive the lugs out in the steps that follow. If the lugs are part of the rotor and not driven through the hub assembly and into the rotor, then you would simply remove the rotor and lay it on something flat, clean and sturdy and use a drift or center punch with a persuasion tool such as a hammer to drive them out by placing the punch on the face of the sheered side of the stud and smack the punch with a hammer driving it out the back side. You then you put the new one on by pushing it through the hole from the back side of the rotor and tap it in until fully seated. Put everything back together and safe travels.

Good Luck.

Posted on Mar 17, 2009

  • 1 Answer

SOURCE: Can not remove lug nut caps 2003 x -type jaguar

I have an 04 xj8. the lug nuts are a good bad example of half baked engineering. the lug nuts are fabricated from ugly steel with an 11/16 hex end. to beautify this, Jaguar overlays the nut end with a stainless steel 3/4 inch cap, crimped to the nut. On top of this, the nut is to be torqued to 90+ ft-lb! The only way to remove the lug nut without damage is with a SIX POINT socket and a breaker bar or an impact wrench. Using a 12 point socket will deform the cap, causing the wrench to spin on the cap and or the cap to spin on the nut itself. If that has happened, it is possible to recover using a 15 oz or thereabouts ball peen hammer and a deep 3/4 inch impact socket (the black ones). Line up the socket to the cap, doing a best guess to where the flats are and give the socket a light blow. Keep trying that until the socket seems to stick on, then hit it harder. Eventually you will find the right point and the socket will go on and reform the cap. Then a breaker bar can remove the cap/nut. New assemblies can be had for about $6 from "partsbin" or "autohausaz".

Posted on Apr 21, 2009

dennymulford
  • 1055 Answers

SOURCE: Can not remove rear tires after removing lug nuts, wheels are jamed onto hub.

spray pentrating oil around where wheel meets hub and also around lug bolts let set for about 15 min then take a sledge hammer and hit from underneath make sure the truck is blocked up good for safty
if that doesnt work take a small sissor jack between the rim and the fram and put a lot of pressure on it then hit it with the sledge from underneath

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My daughters 1991 Accura Integra (automatic) when placed in gear makes a loud grinding sound, the vehicle shakes and shutters when driving ?


ARE THE WHEEL LUG NUTS TIGHT! Poss Brakes grinding the rotors. Any burning smell? CK THOSE TIRES & BRAKES!

Feb 08, 2017 | Acura Integra Cars & Trucks

1 Answer

I am needing to replace a solenoid on my 1992 acura integra but not sure what solenoid I am looking for. It isn't wanting to shift into higher gear when I accelerate at higher speeds


it may not be a solenoid--but dirty fluid or filter or even level--mite be a computer control issue too--have car scanned and a data stream run that shows in detail--a test drive by an experienced tech helps but dont fall fora rebuild cause trans can last to 300 thou miles

Dec 02, 2011 | 1992 Acura Integra Hatchback

1 Answer

My 1995 acura integra blows my taillght/dash cluster light fuse everytime i replace them why is this?


sound like a direct ground, each wire system has it's own color head light, tail lights, turn signal, back up, reverse, best to buy repair Manual for your car and find out what your cars lighting system color are find out what light is blowing your fuse the check those wires for a worn spot or check if a bulb is making contact with metal. if you recently installed big stereo system then problem started see if you nicked wire harness.
best wiring diagram I have found is in a Chilton's manual

Oct 20, 2011 | 1995 Acura Integra Coupe

1 Answer

How do i change the back tire


Find the jack and jack up the rear just in front of the rear tire you are changing. (don't lift off ground completely yet). Using the lug wrench (also called a tire iron) break loose each lug nut.

Finish raising the vehicle just high enough that the tire isn't touching the ground. Finish removing the lug nuts, then pull tire off. Put new (different/spare) tire on, and put the lug nuts back on, and tighten by hand until tire is snug. With the car still raised, lightly tighten the lug nuts, until snug again (by use of lug wrench).

Lower car completely and tighten the lug nuts again (do not over tighten). At all points of tightening lug nuts, do so in a criss cross pattern. Start with one, then move to the one directly across from that, and so on (not all will be "directly" across at all times, so just make sure you alternate and don't go in any consecutive (clockwise/counter clockwise) order.

Let me know if you need further assistance.

carsandcomps,

Guru, Premium Expert @ Fixya.com

May 29, 2010 | 1995 Toyota Camry

1 Answer

I need to replace broken lugnuts


How to Replace Wheel Lug Nuts
(DIY Complexity: Easy / Time: 1.5 hours)

Parts:
1. Lug Nut


Tools:
1. Floor Jack
2. Jack Stand Set
3. Ball Peen Hammer
4. Tire Iron
5. Socket Set


Steps:
Step 1 Secure the vehicle on a solid level surface to ensure that it does not roll or lean when raised.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Break the lug nuts loose but do not remove. Using a floor jack, raise up the front of the vehicle.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 3 Secure the vehicle with jack stands on both sides for safety before starting any work. Do not rely on the jack to hold the vehicle up while working.
o Tip: The pinch welds or the frame rails are the two best locations for vehicle support.

Step 4 Remove the lugs nuts. Inspect the threads on the wheel studs.

Step 5 Install the new lug nuts by hand making sure they thread properly.

Step 6 Tighten each lug nut in a star pattern. Lower the vehicle to the ground and torque the lug nuts to the manufacturer’s specifications.
o Tip: Refer to the owner's manual for the exact location on the vehicle.

Step 7 Road test the vehicle to verify lug nut repair.


I really hope help with this (remember comment and rated this post).

May 15, 2010 | 1993 Honda Accord

1 Answer

How to remove a serpentine belt on a 94 integra


The Belt Diagram should be on the underside of your hood, however they have a way of disappearing.

If it is not there:

Click on the following free direct Link. It has the correct Serpentine and Drive Belt Diagrams for your 1994 Acura Integra 1.8L 4-Cylinder Engine. Included are Instructional and Directional Diagrams for your use.

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1994/make/acura/model/integra/1994_acura_integra_drive_belt_routing_diagram.htm

Note the loosenng of the Alternator Mounting and Adjusting Bolts/Nuts inorder to remove the Drive Belt.

Feb 14, 2010 | 1994 Acura Integra

1 Answer

I need to know how to disconnect my 1995 Acura Integra's kill switch please.


This link will show you many posts on the Honda Acura killswitch bypass.

http://74.125.113.132/search?q=cache:5ur_RTv4fSkJ:www.clubintegra.com/board/showthread.php%3Ft%3D42679+95+acura+integra+kill+switch&cd=3&hl=en&ct=clnk&gl=us&client=firefox-a

Sep 30, 2009 | 1995 Acura Integra Coupe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...