Question about 1993 Toyota Camry

1 Answer

My 1993 Toyota Camry the back driver side door the window the cable came off the motor and need to know how to reset the cable

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 3,961 Answers

This may assist, p37 on

http://www.turboninjas.com/camry/bo.pdf

Posted on Apr 26, 2015

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: repalce front driver power window motor - 1993 cutlass ciera

Disconnect the battery negative cable, carefully remove the door panel, make sure you remove all the visible hold down screws holding the arm rest and other things in place, be careful and observant, don't force anything. If you don't have the standard door panel removal tools, use a stiff putty knife or a wide screwdriver to remove the door panel, you will have to get the power window control switch and the lock control rods out of the way, take notes so you know how they go back together, Remove the plastic weather protection shield out of the way, try not to tear it because you will want to replace it using a good contact adhesive. Getting the motor and the lift mechanism out is the biggest challenge, There are two big rivets holding the motor and regulator assembly to the door, there are two more rivets closer to the rear of the door that holds the track and window guide in place. the rivets are difficult to drill out because it's not easy to center punch them. I used my 4 inch grinder to remove the rivet heads, be careful not to injure yourself or grind through the door metal. knock the rivets out. Remove the power supply wire from the motor. Use a 10 MM socket to untighten the two cap screws that hold the lift bracket to the bottom glass channel. Don't take the cap screws all the way out. Use a piece of wire to hold the window in the closed position. Loop the wire over one of the hold down cap screws and fasten the other end through one of the convenient holes near the top of the door. Now comes the good part. the motor and lift mechanism is all in one near rigid piece. The seat belt anchor blocks the door panel opening that would make it relatively easy to remove. Don't give up, the unit will come out with some thoughtful manipulation, the V shaped track guide will tolerate a small amount of flexing, don't overdo it. I finally got the assembly out by moving it as far to the back of the the door cavity as possible, use the angles of the assembly to your advantage to free it from the door. Once free, use a black marker to ensure you align your new motor in the correct postition. If you are replacing a complete assembly that looks the same a the part you removed, install by reversing the above directions. If you are replacing only the motor, drill out the two rivets that hold the motor to the lift assembly. this will be asy to do. fit your new motor in the exact same position, referring to the previous marks you made. If you are reusing the old lift mechanism, you should pull the perforated tape out of the guide, clean, inspect it, the guide and the tape, relubricate it, I used white grease, there is probably a better grease available. The motor assembly I received from an internet supplier came with rivets and machine screws to install the assembly, I used 1/2 quarter twenty nuts and bolts to replace the big rivets, I don't have a big enough rivet gun. If you go the quarter twenty way, use thread lock, install with bolt heads on the inside the door and flat washers and nuts to the car interior. Be observant, I left the plastic bracket that attaches the drive tape to the window bottom in an unsecure place, one of my dogs used it as a chew toy,so it was off to the junkyard one more time. Be sure to secure the tape properly at both ends. If it worn or frayed, several suppliers including rockauto supply them at reasonable cost. good luck.

Posted on Oct 10, 2008

  • 101 Answers

SOURCE: 1993 Toyota Camry V6 Timing Settings

Get a T belt from toyota. It has 3 white lines on it and and arrow mark. 2 lines are solid and one is broken. Put the arrow facing away from the engine. The cam gears have a dot punched into them near a certain tooth. This is where the solid white lines will line up with. The crank gear will have a dot also. It will line up at 90 degrees from the top, towards the front of the car. This is where the broken line will match up with. With the belt installed with all lines on their proper dots and arrow away from the engine, you valve timming is correct.
Of course you need to remove and compress the tensioner also. I assume you know this already since you didn't ask.

Posted on Apr 16, 2009

bonedivers
  • 1140 Answers

SOURCE: Loose window track in a 2002 Toyota Camry

Look for a missing bolt around frame

Posted on Jul 22, 2009

  • 1986 Answers

SOURCE: need help on replacing door handle on toyota camry

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If it's the inside handle, just disconnect the rod to the back of the handle to replace it. If it's the outside handle, pull back the weather seal and you'll be able to remove the bolts holding down the outer door handle

Posted on Sep 14, 2009

Testimonial: "thanks got the job done ....very good "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1994 Toyota Camry and the power window on the passenger side has gone down, under power. Then nothing would happen when I would pulled up on the switch on the driver side main switch and the also...


more than likely one of the switches are bad (down side of switch works but up side of switch dont) being as the switches are wired together if one goes bad other one won't work either take the switch out one of back doors should be same as front passenger door put rear switch in front passenger door if works then u know front door switch is bad if it doesn't then drivers door switch is bad
u replaced window regulator Did that come with motor too??? if not check to see if motor is good
there is two wires going to motor cut isolation back on wires and using some jumper wires attach one wire to positive terminal of a 12 volt battery attach other wire to negative terminal of battery window should move up or down reverse connections and window should move other way

Jan 29, 2011 | 1994 Toyota Camry

1 Answer

Driver door window will not move. The motor makes


possible broken motor cable or motor gear that move your window up and down, need visual inspection...

Feb 03, 2010 | 1994 Toyota Camry

1 Answer

Driver side window wont roll up??? 1994 Toyota Camry


that model camry has a window regulator that is cable driven. it is very common for that cable to snap and not allow the window to close. it will likely need a window motor/regulator assembly.

Nov 24, 2009 | 1994 Toyota Camry

1 Answer

Loose window track in a 2002 Toyota Camry


Look for a missing bolt around frame

Jul 22, 2009 | 2002 Toyota Camry

1 Answer

My Toyota Camry 2006, the rear left power window behind the driver's side, does not open. I tried to open it using both driver's control and the rear door control. Nothing works. I assume the motor is...


Simple things first, check the dedicated fuse for that window specifcally. if it's ok then check for ground and power at the regulator motor itself. If you have power and ground then it is the motor.

Jul 07, 2009 | 1993 Toyota Camry V6

1 Answer

Installing power window on 1993 toyota camry


Take the door panel off. Disconnect the window and tape it up. Remove the regulator out off the door cavity.

Jun 06, 2009 | 1993 Toyota Camry V6

1 Answer

Window motor fuse location on 92 toyota camry le


look behind the money chance container l side lower dash

g gl

Apr 15, 2009 | 1993 Toyota Camry V6

1 Answer

How do you change the driver's side door window power lift motor on a 2001 toyota camry?


this will help you get the door apart then you can go from there: http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?chapterTitle=Exterior&partName=Body&pageId=0900c15280197342&partId=0900c15280197342

let me know if you have questions

Apr 13, 2009 | 2001 Toyota Camry

1 Answer

Power window motor driver door


I would not consider that issue normal. Camry window motors are quiet.

Oct 05, 2008 | 2006 Toyota Camry

Not finding what you are looking for?
1993 Toyota Camry Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...