Question about 2004 Toyota Highlander

1 Answer

How do I access and replace front pass seat switch and/or motor?

Do I need to disconnect battery to avoid air bag deployment?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 956 Answers

Yes. Disconnect the battery and wait for 90 Seconds before you start your work.

Posted on Apr 13, 2015

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 104 Answers

SOURCE: need to reset air bag light on 1992 toyota tercel

when the light is on is means the system is disabled, check to see if the seats are pugged in properly if they are you need to get the airbag codes to proced

Posted on Apr 25, 2009

  • 51 Answers

SOURCE: the driver side seat belt in my car won't retract

should replace seatbelt if you were invloved in a accident,the force of a crash will damage the seatbelt internals,cheers roady

Posted on Feb 15, 2010

  • 160 Answers

SOURCE: Air bag replacement

you may also need a center sensor assem. it is the brain for the airbag and should only be used once however it is your risk

Posted on Apr 29, 2010

steve_e_uk
  • 1675 Answers

SOURCE: locked front seat belts due

hi these unfortunately are use once only items the pre-tensioners when they "go off" have to be replaced they are like a set charge once used they are useless ...hope this helps

Posted on Jan 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the air bag sensors on a 2000 Lincoln towncar


Sensor - Front Crash Removal
WARNING: Vehicle sensor orientation is critical for proper operation. If a vehicle equipped with an air bag supplemental restraint system (SRS) is involved in a collision, inspect the sensor mounting bracket and wiring pigtail for deformation. Replace and properly position the sensor or any other damaged supplemental restraint system (SRS) components whether or not the air bag is deployed.
WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again.
  1. Depower the system. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in this section.
  1. Remove the radiator upper sight shield (8C291).
  1. Remove the air bag sensor.
    1. Disconnect the air bag sensor electrical connector.
    1. Remove the three screws.
    1. Remove the air bag sensor.
    2. SECTION 501-20B: Supplemental Restraint System 2000 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/10/2004 Sensor - Side Crash Removal
      WARNING: Vehicle sensor orientation is critical for proper system operation. If a vehicle equipped with an air bag supplemental restraint system (SRS) is involved in a collision, inspect the sensor mounting bracket and wiring pigtail for deformation. Replace and properly position the sensor or any other damaged supplemental restraint system (SRS) components whether or not the air bag is deployed.
      WARNING: Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk of injury in the event of an accidental deployment.
      WARNING: To reduce the risk of personal injury, do not use any memory saver devices.
      NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
      NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
      NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again.
      NOTE: Left side is shown, right side is similar.
      NOTE: The side crash sensors are located under the carpet beneath the front seats.
      1. Position the seat to gain access to all fasteners.
      1. Depower the system. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in this section.
      1. Remove the front seat. For additional information, refer to Section 501-10 .
      1. Remove the safety belt anchor bolt cover.
      1. Remove the bolt and the safety belt anchor.
      1. Remove the front and rear door scuff plates.
      1. Remove the lower B-pillar trim panel.
      1. Remove the carpet to access the side crash sensor.
      1. Remove the side crash sensor.
        1. Remove the retaining bolts and position the side crash sensor in order to disconnect the electrical connector.
        1. Disconnect the electrical connector.
        1. Remove the side crash sensor and bracket.

Dec 16, 2015 | 2000 Lincoln Town Car

1 Answer

What is the proper way to depower srS system on a 2006 ford fushion


NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
All vehicles
  1. Turn all vehicle accessories OFF.
  1. Turn the ignition switch to OFF.
  1. At the smart junction box (SJB), located below the LH side of the instrument panel, remove the cover and the restraints control module (RCM) fuse 25 (7.5A) from the SJB. For additional information, refer to the Wiring Diagram Manual.
  1. Turn the ignition ON and visually monitor the air bag indicator for at least 30 seconds. The air bag indicator will remain lit continuously (no flashing) if the correct RCM fuse has been removed. If the air bag indicator does not remain lit continuously, remove the correct RCM fuse before proceeding.
  1. Turn the ignition OFF.
  1. > WARNING: To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag supplemental restraint system (SRS) components and before servicing, replacing, adjusting or striking components near the front or side air bag sensors, such as doors, instrument panel, console, door latches, strikers, seats and hood latches.

    The front impact severity sensor is located on the radiator support bracket near the hood latch assembly.

    The first row side impact sensors (if equipped) are located at or near the base of the B-pillars.

    The second row side impact sensors (if equipped) are located on the C-pillars.

    To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped).

Jul 02, 2015 | Ford Cars & Trucks

1 Answer

Need to replace or reset airbags for 2004 cavalier


when a deployment occur . You need to change both air bag module, change SDM (supplemental deployment module)
need to change the SIR coil Inside column steering and the front discriminating sensor.
Befor installing you need to remove the SIR fuse or disconnect battery
no reset needed

hope it help

Oct 15, 2014 | 2004 Chevrolet Cavalier

1 Answer

Locate airbag sensor


Many are mounted to the floor board under center counsel between front seats. If your airbag has been tripped you must replaces this module. They're hard to order new but I've had good success reusing from junk yard cars that haven't had bag deployed. Warning do not mess with airbag system until battery has been disconnected for at least 2 hours. I disconnect over night. These modules hold a charge with capacitors so it can activate in an accident even if battery cable is severed before bags are deployed. You must give capacitors time to discharge on their own or risk setting off the airbag by working with this system to soon. Of course this warning is only for working on systems that haven't already been set off or deployed. ie when reassembling system.

Sep 14, 2014 | Cars & Trucks

2 Answers

Where is the airbag sensor for the fender on a 95 monte carlo


The sensor consists of a sensing element, normally open switch contacts and a diagnostic resistor. The sensing element closes the switch contacts when the vehicle velocity changes are severe enough to warrant air bag deployment. They are located around the bumpers near the fenders. Look on the framing near the fender. I attached a picture of one.
811507c9-8447-4850-ab90-97c8cc9e8adb.jpg

May 27, 2014 | 1995 Chevrolet Monte Carlo

1 Answer

I have all the functions of the a/c and the associated operations of the dashboard doors when selected, except. no heat whatsoever when selected. The heater core is hot when the engine is @ normal temp....


Hi, this problem is caused by failure of the blend door actuator or structural failure of the door itself. First, access the actuator as instructed below. Have someone turn the key on and change the temperature setting while you watch the actuator. If the actuator turns, odds are the door hinge has failed. In this case, the heater box must be removed from the truck and split open to repair the door.
If the actuator does not move, it may have failed. Remove the actuator and check it for stripped gears or plug it back in and see if it will turn at all when the temperature control is changed. You might also want to check for voltage at the connector before buying a new actuator. A new actuator is about $40.


  1. Disarm the air bag system as explained below.
  2. Open the glove compartment to access the passenger air bag module bolts.

    jturcotte_2121.gif

    Fig. Passenger air bag module view

  3. Disconnect the passenger air bag module electrical connector
  4. Remove the two passenger air bag retaining bolts.
  5. Disconnect the passenger air bag module electrical connector.
  6. Placing one hand in the glove compartment, push the passenger air bag module out and remove it.
    WARNING Do not handle the passenger air bag module by grabbing the edges of the deployment doors.
  7. Remove the defroster opening grill.

jturcotte_2122.gif
  1. Fig. Defroster grill view


  2. Detach and position the RH demister hose aside.
  3. On vehicles with anti-theft/keyless entry, remove the screws and position the anti-theft/keyless entry module aside.
  4. Working through the opening near the RH defroster nozzle, remove the screw.
  5. Disconnect the electrical connector.
  6. Remove the screws and the temperature blend door actuator.
  7. To install, reverse the removal procedure. Tighten the air bag module bolts to 71 inch lbs. (8 Nm).

jturcotte_2123.gif

Fig. Temperature blend door actuator view




Disarming the Airbag System

  1. Turn all vehicle accessories OFF.
  2. Turn the ignition switch to OFF.
  3. At the smart junction box (SJB), located below the RH side of the instrument panel, remove the RH lower cowl trim panel and remove the restraints control module (RCM) fuse from the SJB. For additional information, refer to the Owner-s Manual.
  4. Turn the ignition ON and visually monitor the air bag indicator for at least 30 seconds. The air bag indicator will remain lit continuously (no flashing) if the correct RCM fuse has been removed. If the air bag indicator does not remain lit continuously, remove the correct RCM fuse before proceeding.
  5. Turn the ignition OFF.
    CAUTION To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag supplemental restraint system (SRS) components and before servicing, replacing, adjusting or striking components near the front or side air bag sensors or RCM, such as doors, instrument panel, console, door latches, strikers, seats and hood latches.
  6. To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped).
  7. Disconnect the battery ground cable (14301) and wait at least one minute.

Aug 23, 2011 | 2006 Ford Ranger

1 Answer

Where is the switch to disable the passenger airbag on a 2003 ford taurus


Supplemental Restraint System (SRS) Depowering and Repowering

Depowering Procedure

WARNING: Always wear safety glasses when repairing an air bag supplemental

restraint system (SF3) vehicle and when handling an air bag module. This will reduce

the risk of injury in the event of an accidental deployment.

WARNING: Never probe the connectors on the airbag module. Doing so can result in

air bag deployment, which can result in personal injury.

WARNING: To reduce the risk of personal injury, do not use any memory saver

devices.

NOTE: Ifa seat equipped with a seat mounted side airbag and or a safety belt

pretensioner (if equipped) system is being serviced, the supplemental restraint system

(SES) must be depowered.

NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the

ignition switch is ON. This is normal operation and does not indicate a supplemental

restraint system (SRS) fault.

NOTE: The SRS must be fully operational and free of faults before releasing the vehicle

to the customer

1. Turn all vehicle accessories OFF.

2. Turn the ignition switch to OFF.

3. At the central junction box (Cm), located below the LH side of the instrument panel,

remove the cover and the restraints control module (RCM) fuse F223 (lOA) from

the CTh. For additional information, refer to the Wiring Diagram Manual.

4. Turn the ignition ON and visually monitor the air bag indicator for at least 30

seconds. The air bag indicator will remain lit continuously (no flashing) if the correct

ROsI fuse has been removed, If the air bag indicator does not remain lit

continuously, remove the correct RCM fuse before proceeding

5. Turn the ignition switch to OFF.

6. WARNING: To avoid accidental deployment and possible personal injury, the

backup power supply must be depleted before repairing or replacing any front or

side air bag supplemental restraint system (SRS) components and before set-ricing,

replacing, adjusting or striking components near the front or side air bag sensors,

such as doors, instrument panel, console, door latches, strikers, seats and hood

latches.

To deplete the backup power supply energy, disconnect the battery ground cable

and wait at least one minute. Be sure to disconnect auxiliary batteries and power

supplies (if equipped).

Disconnect the battery ground cable and wait at least one minute.

Repoweri.ng Procedure

1. WARNING: The restraint system diagnostic tool is for restraint system service

only. Remove from vehicle prior to road use. Failure to remove could result in

injury and possible violation of vehicle safety standards.

Make sure all restraint system diagnostic tool(s) that may have been installed during

the repair have been removed from the vehicle and all SRS components are

connected.

2. Turn the ignition switch from OFF to ON.

3. Install the ROsI fuse F2.23 (lOA) to the DB and install the cover.

4. WARNING: Be sure that nobody is in the vehicle and that there is nothing

blocking or set in front of any air bag module when the battery ground cable is

connected.

Connect the battery ground cable.

5. Prove out the supplemental restraint system (SRS) as follows:

Turn the ignition key from ON to OFF. Wait 10 seconds, then turn the key back to

ON and visually monitor the air bag indicator with the air bag modules installed. The

air bag indicator will light continuously for approximately six seconds and then turn

off. If an air bag supplemental restraint system (SF3) fault is present, the air bag

indicator will:

- failto light.

- remain lit continuously.

- flash.

The flashing might not occur until approximately 30 seconds after the ignition switch

has been turned from the OFF to the ON position. This is the time required for the

restraints control module (RCM) to complete the testing of the SRS. if the air bag

indicator is inoperative and a SRS fault exists, a chime will sound in a pattern of 5

sets of 5 beeps. If this occurs, the air bag indicator and any SRS fault discovered

must be diagnosed and repaired.

Jan 12, 2011 | 2003 Ford Taurus

1 Answer

CAN THE PASSANGER SIDE AIR BAG BE TEMPORARILY TURNED OFF TO PUT A CAR SEAT IN IT?


Best way to turn off an airbag is to disconnect the negative battery cable and wait 30 minutes. This avoids overlooking something and having an airbag deployment.

Charlie

Aug 23, 2009 | 2002 Mazda Tribute

1 Answer

Airbag deployed


SECTION 501-20B: Occupant Restraints — Passive — Supplemental Air Bag System 2000 Villager Workshop Manual REMOVAL AND INSTALLATION Module —Driver Air Bag Removal
syv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The backup power supply energy must be depleted before any air bag component service is performed. To deplete the backup power supply energy, disconnect the battery ground cable and wait three minutes.
NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and perform the diagnostic procedure again. If the vehicle was in a frontal collision and the air bag did not deploy, the air bag may not have been needed. Complete a diagnosis of the air bag system before installing a new driver side air bag module (043B13). Refer to Diagnosis and Testing in this section.
  1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 .
  1. Remove the two driver air bag module retaining bolt access covers (one shown).
  1. Remove the steering wheel bottom cover to access the driver air bag module electrical connector.
  1. Disconnect the driver air bag module electrical connector.
  1. syv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: After removing, discard the driver side air bag module bolts and install new driver air bag module bolts during installation.
    Remove the two driver air bag module retaining bolts (one shown) and discard.
  1. Remove the driver air bag module.
    1. Separate the driver air bag module from the steering wheel and disconnect the horn pad switch.
    1. Remove the driver air bag module.

Apr 16, 2009 | 2000 Nissan Quest

1 Answer

How do I install headlight switch on 95 mercury tracer?


  • Headlamps Inoperative
  • Fuse.
  • Headlamp switch.
  • Headlamp relay.
  • Circuit.
  • Bulbs.

Section 11-05: Steering Column Switches 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Multi-Function Switch
Removal
  1. stf~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR AIR BAG DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS.
    Disconnect the battery ground cable (14301) and wait one minute for the backup power supply to be depleted.
  1. Remove the steering wheel (3600). Refer to Section 11-04 for the removal procedure.
  1. Remove the four screws from the lower steering column shroud (3530).




  1. Remove the ignition switch lock cylinder illumination lamp socket from the lower steering column shroud.
  1. Remove the lower steering column shroud.
  1. Remove the upper steering column shroud.
  1. Disconnect the three multi-function switch electrical connectors.
  1. Remove the multi-function switch screws.
  1. Remove the multi-function switch electrical connectors and the multi-function switch (13K359).

Jan 16, 2009 | 1995 Mercury Tracer

Not finding what you are looking for?
2004 Toyota Highlander Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...