Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Where is the oil pressure sending unit on a 1995dodge avenger 6cy.

1 Answer

Greg

Expert 70 Answers
Posted on Mar 15, 2016

Greg

Expert

Joined: Sep 15, 2009

Answers

Questions

Helped

46230

Points

209

It should be behind the Air Conditioning Compressor on the block area. Disconnect neg battery cable. make sure you have your radio code before you disconnect the battery if applicable. You will have to remove the splash shield, Belt on A/C unit and move the Air Conditioning Compressor back to get to the switch. You also may need a special socket to remove the switch. Hope this helps. Thanks Greg

I’m happy to help further over the phone at https://www.6ya.com/expert/gregory_8e6ba270263743ac

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

5 Related Answers

Anonymous

Posted on Nov 07, 2008

SOURCE: oil sending unit

I have heard sludge buildup can be an issue with Dodge engines in Durangos. Make sure sludge is not blocking oil flow and reducing pressure.

Anonymous

1 Answer
Posted on Feb 02, 2009

SOURCE: Pontiac Bonneville(2000) oil pressure sending unit

The oil pressure sending unit is located behind the oil filter, Threaded into an aluminunm housing. It has wiring that plugs into the sending unit. The oil filter has to be removed and you will need a deep well socket and a 6 inch extension. Change the oil and the sending unit together.

Dale Farr

78 Answers
Posted on Mar 17, 2009

SOURCE: oil pressure sending unit

Hi there;

Your looking foer the oil pressure sensor on the 2004 8.1L.
You will find it located directly behind the EGR valve threaded into the block just to the drivers side of the center bolt for the transmission to block connection.

Thanks
Farrout!

Anonymous

1 Answer
Posted on Mar 23, 2009

SOURCE: 01 grand cherokee fan relay/oil pressure

I don't know if this will help anyone, but i had a issue with my jeep running hot and check engine light coming on as well. After alot of trips to different shops - the last one found that there were two senors in the engine for the fan that need to be changed. Everyone would aways fine the one up top but not the second one. After that, have not had any other problems like it since.

Mike Butler

6674 Answers
Posted on Apr 19, 2009

SOURCE: Oil pressure sending unit.

Back of engine, passenger side of distributor, in engine block.

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

Does the dodge avenger se have a fuel shutoff solenoid

Low engine oil level will shut off Fuel pump if more than 1 quart low.....Bad oil pressure sending unit controls Fuel Pump relay also........If more than 4 Years old, it would not hurt to replace it..........

Read full answer

Mar 26, 2019 • Dodge Cars & Trucks

0helpful

1answer

Where is the oil sending unit located on a 2008 dodge avenger 2.4l se?

2.4L Engine;
Oil pressure sending unit is located behind the alternator and under the intake manifold.

Read full answer

Aug 19, 2018 • Dodge Cars & Trucks

0helpful

1answer

Where is the oil sending unit on a 2008 chrysler sebring v6

Looks to be located just below the heat shield for the exhaust header on the right side. Here is images with locations: http://www.autozone.com/repairguides/Chrysler-Cirrus-Stratus-Sebring-Avenger-Breeze-1995-1998/SENDING-UNITS/Oil-Pressure-Sender/_/P-0900c1528008965d

Read full answer

Aug 16, 2016 • Chrysler Cars & Trucks

0helpful

1answer

1995dodge Durango slt 4x4 oil pressure keeps dropping but dose come back..I replaced sending unit.still same problem existing..I just drained the oil it looks kinda funny..kinda slushy with super fine Meta...

With fluctuating oil pressure and metal in the oil you have a fault in the bearings on the crankshaft ( probably main bearing slipper spinning in cap) Best way is to pull the engine , put in stand and tip up side down Quicker in the long run

Read full answer

May 04, 2013 • Cars & Trucks

2helpful

1answer

I need to replace the oil sender switch on my 2002 Buick La Sabre

first need to buy oil pressure sending unit 3/8 deep socket remove oil pressure sending unit you need teflon tap sealer for oil sending unit threads.okay to replace oil pressure sending unit.you need safe raise support vechicle locate oil pressure sending unit next to the oil filter.disconnect oil pressure sending unit wire connector then use oil pressure sending unit 3/8 socket remove the sending unit.then take new oil pressure sending unit use teflon tape white plumbers tape or use thread sealer apply to the oil pressure sending unit threads then install new oil pressure sending unit and reconnect electrical connector to sending unit.then crank engine check for oil leak if all is good lower vechicle back to ground wait several minutes check engine oil level.you good to roll.

Read full answer

Feb 09, 2013 • 2002 Buick LeSabre

1helpful

1answer

Where is the knox sensor on a 1987 chevy r10 pick up truck it has a 4.3 6cy

If you face the engine its on the right side about 10:30 to 11:00 O, clock slightly behind the distubtor shaft torward the fire wall you kind of have to crawl over the engine to see it and by the way the oil pressure sending unit is on the oppisite side same pisition

Read full answer

Dec 01, 2010 • 2003 Chevrolet Suburban 1500

0helpful

1answer

I have a 98 Dodge avenger ES,,, After im driving

could be a pluged oil filter or falty oil sending unit did you try changing your oil

Read full answer

Mar 18, 2010 • 2008 Dodge Avenger

1helpful

1answer