Re: How do i remove a door panel and replace a central...
All door panels will have screws in central area, usually near arm rest, and one forward area mid height, and then clips around the sides and bottom. They are pressure spread plastic gromet like clips, so you just want to pry out slowly at each point which if you look closely as you pry panel out to see where clips are located. Not hard, just don't force anything.
www.FREE-STREAM-TV.com
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
There is only one fuse that mentions 'Locking', but also refers to the General Electrical Module (GEM). If you change the fob battery, you need to reprogram it to the vehicle. Or you could open any Transit around you. Lots of help below including resetting..
In a 2006 Ford Territory, the turn signal relay is located in the central junction box, also known as the fuse box. Here's how you can locate and access the relay:
Find the central junction box: The central junction box in the Ford Territory is typically located under the dashboard on the driver's side. It is usually positioned towards the lower part of the dashboard, near the pedals.
Remove the cover: Once you've located the central junction box, you'll need to remove the cover to access the relays and fuses inside. The cover may have clips or screws holding it in place. Use a flathead screwdriver or the appropriate tool to remove any screws or release the clips to detach the cover.
Locate the turn signal relay: Inside the central junction box, you'll find a grid or diagram that indicates the different relays and fuses. Look for the turn signal relay, which is often labeled with its specific function or identified by a symbol representing the turn signals. Refer to the owner's manual or the diagram inside the junction box for the exact location of the turn signal relay.
Replace or test the relay: If you're experiencing issues with the indicator sound, you can try replacing the turn signal relay with a new one. Alternatively, you can test the relay using a multimeter or consult a professional mechanic to diagnose the problem accurately.
Remember to disconnect the car's battery before working on the electrical components to prevent any electrical mishaps. If you're uncertain about locating or handling the relay, it's recommended to consult a qualified mechanic or refer to the vehicle's service manual for detailed instructions specific to your 2006 Ford Territory model.
either a wiring problem to that door or that lock has failed , strip out door panel and check for power to the lock when using power lock button if no powewr then a wiring fault to be traced if have power then new lock required
Lock the vehicle down. All doors and hoods. Open the drivers door with the key. Start it. No start, lock it down again. Open the passenger side and reach in to start. If it starts, replace the drivers side door latch.
Toyota Corolla Verso - Central locking has just stopped responding
So you don't waste your time, here are some assumptions: -
1. When I press the key fob there is no sound of doors trying to lock/unlock and I know the key fob is fine.
Solution:
In this situation reset the alarm/locking system
Below is the procedure I followed to get the central locking working again: -
Open the passenger door, and look at the side of the dash board. There should be a triangular panel. Pull the panel off to reveal a small set of fuses(see the back of the panel for the fuse map). To power down the central locking you need to remove the Dome Light fuse, this is located top left. Second one down 7.5 amps. (if in doubt remove the top two 7.5 amp fuses I did)
When you remove the fuse(s) you will notice the interior light go out indicating you have powered down the system.
Now leave them out for at least 30 mins so any capacitors can discharge properly. (Be aware while the fuse is removed all central locking is disabled, so the other doors are open. I left the fuse(s) out over night with all the doors open but I don't recommend it, 30 mins should be fine)
After 30 mins replace the fuse(s) close all doors, and then try your key fob, hopefully you should here that satisfying locking sound.
2. When I press the key fob I hear the locking system trying to engage.
This could be a faulty door switch on any door including the boot, or there could be a dent in the inner door panel of any of the doors, usualy the rear doors due to the seat belt not retracting properly.
Solution:
Check all door switches for damage, and check inner panel for dents, just a small dent where the switch connects can be enough to not engage the switch. This will stop the central locking.
Use some kitchen roll wrapped in tape (as a makeshift pad) and tape to the inner door as a temp measure to engage the door switch. At least you can then lock the car.
×