Question about 1994 Plymouth Sundance

1 Answer

I need all the engine diagnostic codes for a 94 plymouth sundance

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Plymouth Master
  • 85,111 Answers

11 Timing belti need all the engine diagnostic codes for a 94 - 2.gif skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 Direct battery input to PCM/ECM was disconnected within the last 50 key-on cycles (normal)
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failur

Posted on Aug 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel pump fuse on a 94 plymouth sundance


I would not think a fuse would be the problem. A fuse either blows or it is good. The relay might be at fault, but I would think it is the pump going bad.

Aug 09, 2014 | 1994 Plymouth Sundance

1 Answer

1994 plymouth sundance with loss of horse power


On this i think you will find you have a pluged cadilac converter. Try taking the bolts out of the pipe going to the convert and move it out of the way so not to restrict the exhaust. You may need to wire it up to the bottom of the car so it wont drag. It is going to be loud but take it for a run if it accelerates like it should you will need to replac the converter. If it doesnt then check for a code on the TPS switch. { Throttle Posions Sencor} Good luck and hope this helps.

Nov 24, 2012 | 1994 Plymouth Sundance

1 Answer

Engin light on 94 plymouth sundance


Check this procedure...
8_27_2012_5_04_55_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 27, 2012 | 1994 Plymouth Sundance

1 Answer

I ran my car with old gas (2 years old) then it stopped running. I have changed the gas,plugs .the self diagnostic system check came up with code 12 problem with standby memory circuit.I could use any...


The old fuel could have clogged the fuel filter, pump, lines and/or injectors. I'm not sure about the code on your model but I believe it refers to the circuit that supplies power to keep your radio presets and clock set when the ignition is turned off.

Mar 11, 2011 | 1994 Plymouth Sundance

1 Answer

Timing mark for the timing belt for a 1994 plymouth sundance


i need to find the timing marks are for a 94 plymouth sundance

Mar 04, 2011 | 1994 Plymouth Sundance

1 Answer

93 Sundance stutters and jerks on acceleration


It hooks up to the diagnostic port by the battery. But it sounds like you need plug wires.

Jun 11, 2009 | 1993 Plymouth Sundance

1 Answer

'89 plymouth sundance


You need a timing belt

Aug 09, 2008 | 1989 Plymouth Sundance

1 Answer

94 Plymouth Sundance.. engine light and sluggish from dead stop! Help


What you do is turn the ignition to the "on" position and back to the "off" position 3 times. On the last "on/off" cycle, leave the key in "on". The check engine light will start flashing. The first group of flashes is the 1st number of the code. There will be a pause and then a 2nd set of flashes will be the 2nd number of the code. If there's more than one code, there will be a pause and then there will be another set of flashes for the next code and so on. A Haynes or Chilton's repair manual, available at any parts store, will tell you what the codes mean.

Jul 09, 2008 | 1994 Plymouth Sundance

Not finding what you are looking for?
1994 Plymouth Sundance Logo

1,033 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...