How do I check ball joint wear on a 2005 Chrysler Sebring?

when it comes to ball joints do both upper and lower never just one can come back to bite you in the end

Its possible something in the suspension is showing signs of wear. Check the ball joints and sway bar connections for free play or looseness. Check any torsion arms and the a-arms or wishbone. Hope it helps.

Sounds like you might have some worn ball joints. I would have the suspension checked ASAP. My one customer had the same thing with a Sebring, the ball joint broke and took out the axleshaft. The ball joints are $160.00 each, because you have to buy the whole control arm.

It depends on exactly which ball joint of the 3 per side your changing, but here are the details.

COMPRESSION LOWER ARM & LATERAL LOWER ARM ASSEMBLIES
Removal
1. Loosen compression lower arm ball joint nut. Using steering linkage puller, separate ball joint and
knuckle. Remove nut, bolts and compression lower arm assembly. Remove dust cover.
2. Remove stay. Remove shock absorber lower mounting bolt. Loosen lateral lower arm ball
joint and knuckle nut. Using steering linkage puller, separate ball joint and knuckle. Remove nut, bolt and
lateral lower arm assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for compression lower arm ball joint is 4-22 INCH lbs. (0.5-2.5
N.m) for 2000 models. On 2001 models, breakaway torque is 22-54 INCH lbs. (2.5-6.1 N.m). Ensure
breakaway torque for compression lateral lower arm ball joint is 13 INCH lbs. (1.5 N.m). Check compression
lower arm, lateral lower arm, dust covers, and bushings for damage and wear.
Installation
To install, reverse removal procedure. Use NEW ball joint nuts. Lubricate lip and inside of dust cover with
multipurpose lubricant. Using installer, install dust cover. Check front wheel alignment.
UPPER ARM ASSEMBLY
Removal
Using steering linkage puller, loosen upper arm ball joint and knuckle nut. Remove self-locking nut. Remove upper arm and upper arm shaft assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for upper arm ball joint is 3-13 INCH lbs. (0.3-1.5 N.m).
Replace upper arm assembly when measured value exceeds specification. Check upper arm, dust cover, and
bushings for damage and wear.
Installation
1. To install, reverse removal procedure. Use NEW self-locking nuts. Lubricate lip and inside of dust cover
with multipurpose lubricant. Using Ball Joint Installer (MB990800), install dust cover.
2. Ensure upper arm shaft assembly is installed at indicated angle. Verify upper arm shaft
assembly installation. Check front wheel alignment.

Once you have the correct arm off and a replacement joint (if available, some are not serviceable and require the arm to be replaced) then you will need a press or a ball joint press to change the joint. Such as
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=38335

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46389

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=66958

or http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46967

NO REAR BALL JOINTS

grease ball joints that should fix it

it is part of the control arm simply unbolt the arm and remove it

Look at ball joints tops an bottom, if they do not have a grease feeding, perhaps model is seal, or You need to install grease feedings some cars simply don't have them

these ball joints can not be greased factory sealed!

The dealer's answer (if you are interested).......

The ball joint is pressed into the upper control arm and has a tapered stud for attachment to the steering knuckle. The ball joint stud is attached and locked into the steering knuckle using a special nut. The ball joint is a sealed-for-life type and requires no maintenance. If the ball joint is defective it will require replacement of the entire upper control arm.

Sorry.