1995 Chevrolet Lumina Logo
A
Anonymous Posted on Feb 10, 2015
Answered

Disarm airbag in 1995 carburated chevy 350 - 1995 Chevrolet Lumina

Answer This Question

1 Answer

robert wales

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Chevrolet Master 4,977 Answers
  • Posted on Feb 10, 2015
robert wales
Chevrolet Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Mar 01, 2011
Answers
4977
Questions
0
Helped
1332550
Points
59541

SRS systems use a yellow electrical connector plug. look for it under the dash for the drivers side it should be near the steering colume by the lower dash panel. disconnect it and the bag will not work however the SRS light will come on. you could find the module for the system and disconnect it. you could also try removing the fuse if it only controls the system. be aware that you could be legally breaking the law as your disconnecting a safety feature.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0answers

How do i disarm my airbag
Read full answer
Be the first to answer Jun 30, 2014 • 1995 Oldsmobile Cutlass Ciera
0helpful
1answer

1996 Chevy c1500 ext cab automatic. Replacing ignition key cylinder. Everything says to disable airbag but nothing says how to. Do not have owners manual anymore on this truck. So how do we disable this...
You can disable the airbag by disconnecting the battery and waiting 15 minutes. Power is stored in the electronics of the air bag and if you wait about 15 minutes it will discharge and the airbag should be disarmed.
Read full answer
Jul 19, 2011 • Chevrolet C1500 Cars & Trucks
0helpful
1answer

Airbag blinker is alwyas on
When the airbag light (SRS) is on or blinks it means a fault has occurred in the system and the airbag diagnostic monitor has disabled the system, the most common problem that turns the light on is a break in the connection to the steering wheel mounted airbag, this is due to a rotating ribbon contact that breaks under the steering wheel that connects the airbag to the wiring harness and the diagnostic monitor, the part is called the clock spring contact, a coiled up ribbon electrical contact that turns with the steering wheel while maintaining a mechanical connection to the airgag mounted on the steering wheel, to replace this part you must disarm the airbag system and remove the steering wheel, this requires a special steering wheel puller tool and that you disarm the airbag system before you start the work, to do this disconnect the battery negative cable for 1 hour prior.
Read full answer
Apr 07, 2010 • 1995 Nissan 200SX
1helpful
1answer

95 lincoln airbag light on
When the airbag light (SRS) is on or blinks it means a fault has occurred in the system and the airbag diagnostic monitor has disabled the system, the most common problem that turns the light on is a break in the connection to the steering wheel mounted airbag, this is due to a rotating ribbon contact that breaks under the steering wheel that connects the airbag to the wiring harness and the diagnostic monitor, the part is called the clock spring contact, a coiled up ribbon electrical contact that turns with the steering wheel while maintaining a mechanical connection to the airgag mounted on the steering wheel, to replace this part you must disarm the airbag system and remove the steering wheel, this requires a special steering wheel puller tool and that you disarm the airbag system before you start the work, to do this disconnect the battery negative cable for 1 hour prior.
Read full answer
Jan 07, 2010 • 1995 Lincoln Town Car
0helpful
2answers

Step by step instructions on removing intake manifold on 1992 buick roadmaster limited
  1. On models equipped with airbag, disable airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING .
  2. On all models, disconnect battery ground cable, drain cooling system and remove air cleaner.
  3. Disconnect accelerator, transmission and cruise control linkages, as equipped.
  4. Disconnect fuel line from carburetor or TBI unit and remove fuel line clips as needed, then remove carburetor or throttle body from intake manifold.
  5. Disconnect necessary vacuum hoses and electrical connectors, noting position for installation.
  6. Disconnect upper radiator and heater hoses from manifold.
  7. On Cadillac Brougham models, remove thermostat and housing.
  8. On all models, remove distributor.
  9. Remove ignition coil, AIR pump, cruise control servo and brackets, as needed.
  10. Remove alternator upper mounting bracket and EGR solenoids.
  11. Remove manifold retaining bolts and the manifold.
  12. Reverse procedure to install, noting the following:
    1. Ensure surfaces are clean and dry, then apply 3/16 bead of RTV sealer on each block ridge and apply suitable sealer around water outlets, install gaskets and secure gasket position by extending bead of sealer approximately 1/2 inch onto gasket ends.
    2. Install manifold and retaining bolts, ensuring areas between case ridges and manifold are completely sealed.
    3. Torque manifold bolts to specifications in sequence shown in Figs. 2 and 3.
    4. After installing carburetor or TBI unit, check to ensure no fuel leakage is present.
  1. Rearm airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING
Read full answer
Jul 21, 2009 • 1992 Buick Roadmaster
1helpful
2answers

Horn doesn't work , does it take a fuse for it to work?
yes...... check fuse block carefully
Read full answer
Jun 23, 2009 • 1995 Chevrolet Cavalier
1helpful
1answer

Disarm airbag in chevy blazer
You need to disconnect the battery from the vehicle, and wait at least 1 minute to disable the airbag system. Your airbag system is designed to hold energy for 1 minute after a power failure, and will deploy if you do not wait 1 minute.
Read full answer
Jun 09, 2009 • 1996 Chevrolet Blazer
0helpful
1answer

Cruse controll doesn't work
You must do the book time to fix the problem, that said you most likely need the part below.
.In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to follow factory Airbag disarming protocol can result in an unexpected Airbag deployment and possible serious personnel injury or death
Read full answer
May 26, 2009 • 1995 Subaru Impreza
1helpful
1answer

Cruise Control does not work
In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to follow factory Airbag disarming protocol can result in an unexpected Airbag deployment and possible serious personnel injury or death

My background is 20+ years as a Ford dealer tech.
Read full answer
Apr 22, 2009 • 1995 Ford Taurus
0helpful
1answer

Curse control worked on and off fore about 6mos.Then it quit working at all 95 ford taurus
In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to follow factory Airbag disarming protocol can result in an unexpected Airbag deployment and possible serious personnel injury or death.
Read full answer
Mar 13, 2009 • 1995 Ford Taurus
Not finding what you are looking for?

View Most Popular

1995 Lumina

  • Cars & Trucks

Related Question

How do i disarm my airbag

  • 1995 Oldsmobile Cutlass Ciera

Related Topics

72 views

Ask a Question

Usually answered in minutes!

Popular Questions

Fuel injector fuse is blown, keeps blowing. Engine turns but won't catch and start.

1995 Chevrolet Lumina

Cyl head torque on 05 3.4l chev equinox

1999 Chevrolet Lumina

DIAGRAM OF THE FIRING ORDER CHRYSLER 300 3.6

1998 Chevrolet Lumina

Vauxhall astra auot code P1895 what does it mean

1997 Chevrolet Lumina

I locked my keys in my car. how do you break into

1997 Chevrolet Lumina

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...