Replace rear window

Preliminary Procedures
Remove the rear seat. Refer to Rear Seat Replacement.
Remove the left quarter lower trim panel. Refer to Quarter Lower Rear Trim Panel Replacement.


Preliminary Procedure
Remove the rear compartment floor stowage compartment tray. Refer to Rear Floor Trim Plate Replacement.
1
Rear Seat Nut (Qty: 6)
Caution: Refer to Fastener Caution in the Preface section.
Tip
Roll the seat forward enough to get access to the nut that attaches the center seat belt assembly to the floor.
Tighten
45 N·m (33 lb ft)
2
Rear Seat Bolt (Qty: 3)
Tip
• Adjust the seat forward or rearward to access the bolts.
• Remove the plastic trim pieces to gain access to the nuts.
Tighten
45 N·m (33 lb ft)
3
Rear Seat Assembly

Preliminary Procedures
Remove the quarter upper trim finish panel. Refer to Quarter Upper Trim Panel Replacement.
Remove the rear compartment trim panel. Refer to Rear Compartment Trim Panel Replacement.
Remove the floor trim plate. Refer to Rear Floor Trim Plate Replacement.
1
Quarter Lower Trim Finish Retainer (Qty: 2)
2
Quarter Lower Trim Finish Panel Assembly
Caution: Refer to Fastener Caution in the Preface section.
Procedure
Remove the cargo tie down loop anchor plates and bolts.
Remove the rear passenger seat belt guide.
Disconnect the rear passenger seat belt so that the trim panel can be removed around the seat belt. Refer to Rear Seat Belt Replacement.
Pull the trim panel toward the inside of the vehicle to disengage the retainers.
Tighten
9 N·m (80 lb in)
3
Quarter Lower Trim Finish Panel Retainer (Qty: 5)

Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Same place you fill for the front washer fluid ! Your fronts work but not the rear ? There are to washer pump motors on the washer fluid bottle , one for the front an one for the back . Rubber hose goes all the way to the back . If that hose has failed ,to replace it you basically have to pull out your vehicles interior .
Rear Window Washer Hose Replacement - Pump to Endgate
Removal Procedure

1. Remove the left front seat. Refer to Bucket Seat Replacement in Seats.
2. Remove the rear seat. Refer to Rear Seat Replacement in Seats.
3. Remove the endgate/liftgate door sill plate. Refer to Rear Floor Rear Trim Plate Replacement or Liftgate Door Sill Plate Replacement in Interior Trim.
4. Remove the left front and left rear door sill plates. Refer to Door Sill Plate Replacement in Interior Trim.
5. Remove the left body side trim panel. Refer to Body Side Trim Panel Replacement in Interior Trim.
6. Remove the left hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement - Left Side in Interior Trim.
7. Fold over the left side of the carpet to allow access to the body harness. Refer to Front Floor Mat/Carpet Replacement and Rear Floor Panel Carpet Replacement in Interior Trim.

Disconnect the washer hose connection (1) from the body harness (2) at the endgate. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls.
Disconnect the hose (1) from the rear washer pump. Install a plug to the rear washer pump nozzle to prevent washer fluid loss. Push the hose grommet (2) in through the bulkhead.
Pull the washer hose (1) into the vehicle though the bulkhead. Cut the old washer hose off where it enters the body wiring harness (2). Remove the hose end from the vehicle
Or it could be the pump , they go bad . switch the hoses from one pump to the other an see if you get washer fluid at the back ,if you do the pump is bad ,if not the hose or the spray nozzle is clogged . You probably will need to pull the washer fluid bottle to see both pumps

To get at the speaker, you need to remove the rear window shelf trim panel -
Remove rear seat lower by lifting from front;
Remove bolts holding rear seat back and remove seat back; Remove the seat belt retractors;
Remove the push in retainers from the cross car beam;
Lift up on the front of the shelf panel to disengage the hook and loop material; then do the same at the rear of the panel, and pull out the shelf.
The speaker is now accessible for removal.

Manual says to remove rear seat bolsters

I guess that is the rear window trim

I have removed the front ones on my LS but never
the rear ones

I guess they just pull away & are spring loaded or attached

Then pull down the head liner & remove two bolts &
unplug the rear high stop lamp assy

For seats problem,check the help links given below :----How to remove Seat on car?

http://repairhelpcenter.blogspot.com/2011/11/how-to-remove-seat-on-acura-integra.html

-----------------
Replacing power adjustable bucket seats to both heated and cooled seats? http://schematicsdiagram.blogspot.com/2011/12/replacing-power-adjustable-bucket-seats.html
----------How to Refit Rear seat? http://repairhelpcenter.blogspot.com/2012/01/how-to-refit-rear-seat-on-rover-600.html
--------How to Remove Rear seat? http://repairhelpcenter.blogspot.com/2012/01/there-are-3-10mm-bolts-at-back-of-seats.html
---------second row seat will not fold? http://technoanswers.blogspot.com/2012/01/ford-freestyle-second-row-seat-will-not.html
------------

For all types of power window problem and power windows not working,i suggest you to go through the help links given below.Click the link to go through its procedure to troubleshoot the problem :------

Power window problem?
http://repairhelpcenter.blogspot.com/2012/01/pontiac-grand-am-power-window-not.html
------------

rear door or window will not open ?
http://technoanswers.blogspot.com/2011/06/rear-door-or-window-will-not-open-on.html
--------------
How to remove door panel, door window motor and regulator ?
http://technoanswers.blogspot.com/2011/05/how-to-remove-door-panel-door-window.html

--------

Power windows not working after car wash?

http://howtobyme.blogspot.com/2011/11/power-windows-not-working-after-car.html
---------power locks, power window and power mirror not working?
http://howtobyme.blogspot.com/2011/09/power-locks-power-window-and-power.html

All power windows not working?
http://howtobyme.blogspot.com/2011/09/all-power-windows-not-working-on-2003.html
------------
-------------Complete Diagnosis & Testing Power Windows?

http://repairhelpcenter.blogspot.in/2012/02/diagnosis-testing-power-windows.html

------------

How to replace power window motor in car?
http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-power-window-motor-in.html
----------
HOW TO REPLACE A POWER WINDOW SWITCH
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-power-window-switch.html
------------
How to Replace a Window Motor
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-motor.html
----------
HOW TO REPLACE A WINDOW REGULATOR WITH MOTOR
http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-window-regulator-with.html
---------
HOW TO REPLACE WINDOW RUN CHANNEL SEALS
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-run-channel-seals.html
-------
HOW TO REPLACE A WINDOW REGULATOR
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-window-regulator.html

-----------This will help.Thanks.

Removal Procedure

Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: Before cutting out a stationary window, apply a double layer of masking tape around the perimeter of the painted surfaces and inner trim of the window.

1. Use safety glasses and gloves.




2. Carefully spread the handle retainer outward in order to release the latch pin from the latch.
3. Remove the latch pin from the latch.
4. Remove the seat belt retractor. Refer to Front Seat Belt Replacement in Seat Belts.
5. Open the door in order to access the rivets.
6. Drill out the rivets retaining the window assembly.
7. Thoroughly clean all metal particles that may have lodged inside the body panel.
8. Remove the window assembly from the vehicle.

Installation Procedure

1. Install the window assembly to the vehicle.
2. Using the J 34940 (or equivalent), install the rivets in order to retain the window assembly to the vehicle.
3. Install the seat belt retractor. Refer to Front Seat Belt Replacement in Seat Belts.
4. Install the latch pin.
Using a punch, carefully drive the pin into the latch.

Long job and not for the faint of heart.

Open roof to rear.

Pull up on rear seat bottom and remove it.

Remove center panel.

Remove three Allen head bolts down behind seat cushion back.

Lift off head rests...pull up.

Raise top just enough to make side flaps flip up.

Remove nut at top rear corner.

Remove Nylon/plastic push lock rivet where seat belt goes through panel... top corner.

Pull panel off mounting pins...will sound like your breaking it !

Lift panel to access seat belt bolt and unplug Flip-Up panel motor.

Remove cable from it's clip.

Remove loom thro' panel.

Pull seat belt thro panel.

Set panel to one side.

Remove Torxs bolts around black plastic panel for speaker.

Unplug speaker.

Pull loom thro' hole.

Remove two Allen and 5 hex bolts where window would come out. if it worked.

Pull up plate and remove rubber seal to one side and then remove plate. remove two nuts at bottom of regulator and one half way up towards front.

Lift regulator and window glass up thro' top to gain access to three nuts holding glass tho regulator.

Lift out window and then regulator....little maneuvering and levering required.

FYI....Take digital pictures as you remove stuff for later reference.


New regulator and glass is around $600.00 from dealership and only the dealership.

you have to remove the seat, remove the lower part first, it snaps in, then remove top part of seat, then you will see the pop in fasteners that hold the rear deck. if you have a problem go to this web site it will help with step by step instrucations. hope this is helpful. chttp://www.crutchfield.

Not 100% sure on yours but normally you'll either have a couple of bolts way down under seat cushion at front, near floor, or in some cases, you have to push seat cushion back toward rear window, hard & lift, to pop it out of notched catch under it.