Suddenly stop the Ignition Key remote control function on my ML 320,then I used the spare Key remote control, just after one week spare remote control stop function I replaced the battery in correct order didn't function, then I felled the procedure on the owners manual, only one time it function and stops I can open or closes the doors only one time.
now I am using manual look switch on at middle of the console to close the doors and key to open.
I anyone can help me to resolve this problem to use my remote control appreciated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Procedure
1. Switch Ignition ON and leave the key in the ignition.
2. Mechanically lock the vehicle using the Drivers door using a second
key.
3. Using the remote control press the Unlock button once, and the horn
will sound once.
4. Wait 6 seconds and press the unlock button once to activate the coding
procedure. The remote control will now be programmed.
NOTE : When performing programming on additional remotes the procedure
is the same, except you press the unlock button 2, 3 or 4 times for the
different remote.
For example : If programming 2 remotes press the unlock button twice with
a 1 second interval between each press, repeat for 3 and 4 remotes.
5. Switch Ignition OFF.
6. Remove key from ignition and check for operation.
7. The coding procedure can be repeated up to 4 times for additional remotes.
8. The ignition must be switched OFF between programming each remote
control.
Jun 12, 2008 - Best Answer: A new ML remote key purchase has to be programmedby your local MB dealership service dept and should not charge you more ...
? 2:42
https://www.youtube.com/watch?v=g2E3yXfy-h0
Jan 6, 2012 - Uploaded by d3sodotcom
Please help me figure out what's wrong with my 99' ML320. ...help me it is 2002 ML320 also does anyone no where I can get a good used rear bumper .... After the car wouldn't spark when I turn the ignition key on. .... Mercedes automatic transmission reset/reprogram 722.6 automatic - Duration: 3:46. by ...
Synchronization Turn ignition switch to position II. Turn ignition switch to position 0 and remove key. Within 1 minute: Press and hold key lock button. Press unlock button 5 times. Remote control should now operate system. If not: Repeat procedure. Programming When Key remote control added or replaced. System malfunction. How Keys can only be programmed using diagnostic equipment.
You may have to reprogram the remote. Follow these steps CAREFULLY;
Remote Control Programming (1997 ON) 1. Switch Ignition ON and leave the key in the ignition. 2. Mechanically lock the vehicle using the Drivers door using a second key. 3. Using the remote control press the Unlock button once, and the horn will sound once. 4. Wait 6 seconds and press the unlock button once to activate the coding procedure. The remote control will now be programmed.
Synchronization Turn ignition switch to position II. Turn ignition switch to position 0 and remove key. Within 1 minute: Press and hold key lock button. Press unlock button 5 times. Remote control should now operate system. If not: Repeat procedure. Programming When Key remote control added or replaced. System malfunction. How Keys can only be programmed using diagnostic equipment.
NOTE this only works on ml up to 05
Synchronization Turn ignition switch to position II. Turn ignition switch to position 0 and remove key. Within 1 minute: Press and hold key lock button. Press unlock button 5 times. Remote control should now operate system. If not: Repeat procedure. Programming When Key remote control added or replaced. System malfunction. How Keys can only be programmed using diagnostic equipment
Keyless Entry System Circuit Description
The Power Door Locks/Remote Keyless Entry control system provides several functions. The driver operates the vehicle door locks and rear window release from outside the vehicle using a hand-held radio transmitter. The transmitter sends coded signals to the remote control door lock receiver. The remote control door lock receiver detects and decodes the signal from the transmitter. The remote control door lock receiver issues signals to the body control module (BCM) through a serial data link. The BCM actuates relays to lock and unlock the doors and liftgate. The BCM can also release the liftglass. The power door lock switches provide manual control of the door locks.
Transmitter Programming
Important: Different keyless entry systems are used on General Motors vehicles. The parts are not interchangeable even though the parts may appear to be similar. Observe the back of the transmitter in order to properly identify the system. On 1998 S/T pickups and utilities, use a transmitter identified with GM/UTA preceding the part number.
With the driver door closed, hold down the power unlock button on the door panel.
Turn the ignition switch to the ON position.
Turn the ignition switch to the OFF position.
Turn the ignition switch to the ON position.
Turn the ignition switch to the OFF position.
Release the power unlock button on the door panel.
The remote control door lock receiver will respond in the following manner in order to indicate that the receiver is in the programming mode:
6.1. Locking the doors
6.2. Unlocking the doors
Important: All extra transmitters must be programmed at this time. When a new transmitter is programmed, it will deactivate the old transmitters.
Hold down the lock and unlock buttons on the transmitter until the remote control door lock receiver will respond in the following manner:
7.1. Locking the doors.
7.2. Unlocking the doors.
Repeat step 7 for each additional transmitter.
Turn the ignition switch to the ON position in order to exit the transmitter programming mode.
remote controls trasmit frequencies. I believe you hold your home remote control device within 2" to 5" of the car's remote control buttons. You select one button in the car which you wish to use as the garage access remote, and press it simultaniously with the home remote control button long enough for the blinking light to go on and blinks for 5 seconds. Then you are programmed. Test it to make sure it worked. If failed, try again. If it doesn't work, any Mercedes Dealership should do it for you FREE. Some of them now push for some money, but you tell them that you called Mercedes and based on your zip code they said you should go to this dealership and it will be done for FREE! They will take care of it immediately.
there should be a button some where that you can push while the key is in the on position and it will stop the alarm for that ignition cycle. Then i reccomend taking the alarm out or take it to a reputable electronics shop and they can tell you what manufacture and model is.
Procedure 1. Switch Ignition ON and leave the key in the ignition.
2. Mechanically lock the vehicle using the Drivers door using a second key.
3. Using the remote control press the Unlock button once, and the horn will sound once.
4. Wait 6 seconds and press the unlock button once to activate the coding procedure. The remote control will now be programmed.
NOTE : When performing programming on additional remotes the procedure is the same, except you press the unlock button 2, 3 or 4 times for the different remote.
For example : If programming 2 remotes press the unlock button twice with a 1 second interval between each press, repeat for 3 and 4 remotes.
5. Switch Ignition OFF.
6. Remove key from ignition and check for operation.
7. The coding procedure can be repeated up to 4 times for additional remotes.
8. The ignition must be switched OFF between programming each remote control.
Remote Control Erasing (1997 ON)
Procedure 1. Switch Ignition ON and leave the key in the ignition.
2. Mechanically lock the vehicle using the Drivers door using a second key.
3. Press the remote control unlock button 5 times in 1 second intervals. A short horn will sound.
4. Wait 6 seconds and press the unlock button once to activate memory erase.
5. Switch ignition OFF, all remotes are now erased.
×