Question about Cars & Trucks

1 Answer

How do I arrange the wires at the back of the plazma at the moment they are affecting the picture.?

The picture starts to break-up I believe its because the wires are so heavy in this position that they pull slightly out of the jacks hence the break-up picture whom should I get to rectify this?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,585 Answers

The wires are slack because of weight? replace the wires. The wires will give way before the jacks inside the TV will. Use shorter wires or set them so they don't bend at the TV ports.

Posted on Dec 16, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What can cause the car not to start after changing the valve cover and intake gaskets?


Changing the intake gasket requires removal of distributor I believe. Did you get it back in the exact correct position?

Dec 01, 2014 | 2004 Chevrolet TrailBlazer

3 Answers

Astro cranks but won't start


check the preccion from fuel pump..
I believe is going brother that happen very often on astros

Jan 29, 2013 | 1998 Chevrolet Astro Van

1 Answer

Power door locks won't work and the instrument pnnel lights won't turn on. I replaced blown fuse a 20mp one in position 14 I believe. worked ok till I tried to lock the doors, the fuse blew


Hello. Try looking at the black earth that goes from the drivers door and into the A frame which is covered in a rubber sheath. The wire can break after opening and shutting the door over several years and as it's normally the thicker wire is more prone to break. Also check the other wires visually for any chaffing and tugging on each wire. If more electrical parts start failing, air con blowers etc it will be an earth. Hope this helps

Nov 03, 2012 | 2002 Dodge Neon

3 Answers

Just had new clutch and flywheel fitted,now wont start,is there a specific place for timimg the flywheel


No timing of the flywheel to the starter. Flywheel does not affect ignition timing.

Mar 11, 2010 | 1999 Isuzu Trooper

1 Answer

Squealing Noise from Back of Truck


It could be that the Compression Cylinders inside the Drums at the Top are Worn and are Pressing all the Way out. I would Overhaul Both sides, Inside and Out.

Jan 15, 2009 | 2000 Chevrolet S-10

1 Answer

99 4runner po302 code


Yes. No clicking indicates a bad injector; you mentioned you had a Noid light; does it pulse?

If you remove the plenum to replace the injector, buy new plenum gaskets. You should not reuse them.

The graciousness of a FixYa rating for my assistance would be appreciated.

Dec 28, 2008 | 2001 Toyota Tacoma

2 Answers

E200 wont start


If as you say you have a pulse at the ecu and nothing at the nozzles then therse a break in that circuit either purposely (anti theft etc)or accidently.You will have to back probe to find which of the wires has been affected.Usualy only two wires.A continuity test with noise will tell you which of the two has the break.It then becomes a case of tracing that wire back to its source and identifying what is stopping the flow of current.Idont have a diagram for your vehicle so cant help in that respect.An earth wire may have been left off during replacement of the crank angle sensor.Even something as simple as a plug with a poor connection could be the cause.good luck and sorry i cant be more specific.

Oct 24, 2008 | 1999 Mercedes-Benz E-Class

1 Answer

Map sensor pin arrangement dodge cavan 2003


Hello, here is a picture of the connector and wiring.

85cdf8a.gif MANIFOLD ABSOLUTE PRESSURE SENSOR (GAS) - BLACK 3 WAY CAV CIRCUIT FUNCTION 1 K1 18VT/BR (3.3L/3.8L) MANIFOLD ABSOLUTE PRESSURE SENSOR SIGNAL 1 K1 18VT/BR (2.4L) MAP SIGNAL 2 K900 18DB/DG SENSOR GROUND 3 F855 18PK/YL 5 VOLT SUPPLY

Pink/Yellow is #3, Blue is #2, and Purple is #1. Your colors may appear slightly different

Oct 06, 2008 | 2003 Dodge Grand Caravan AWD

1 Answer

X5 break lights


Hi there!

Check the Earth / return wires for these lamps. Often just screwed to a piece of chassis. If there is corrosion on the connector, then you will get an intermittent fault.

Unusual that both lights are doing this - usually just the one is affected.

Hope this enables the problem to be solved; If it does , please take a moment to rate as Fixya. Thanks.

Jun 16, 2008 | 2001 BMW 5 Series

1 Answer

Need suggestions on how to fix my truck


check the wires going to the coil two sets on that one I believe they break easily

Jun 12, 2008 | 1990 GMC C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...