Question about 2004 Mazda 6 Hatchback

1 Answer

How do I replace rear tail light assemble

Do you have a diagram of how to remove the trim

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 742 Answers

Unbolt it from inside trunk

Posted on Dec 16, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace rear tail light assemble


tail light assemblies are either held in with screws from the outside which hold the lens and the assembly in place or you have to remove the trim in the boot and undo small nuts on bolts to take the assembly out to the rear.

Dec 15, 2014 | 2004 Mazda 6 Hatchback

1 Answer

2009 impala rear turn signsl bulb replacement


Tail Lamp Replacement Impala
1596323.gif
tif.gif
Callout
Component Name
Preliminary Procedures
  1. Open the rear compartment lid.
  2. Remove the nut securing the rear compartment trim the backside of the tail lamp assembly.
  3. Pull down the rear compartment trim liner.
1
Tail Lamp Assembly Nuts (Qty: 2)
Caution: Refer to Fastener Caution in the Preface section.
Tighten
2 N·m (18 lb in)
2
Trunk Trim Line Nut
Tip
Ensure the trim liner nut is installed after the liner is repositioned in the rear compartment.
3
Tail Lamp Assembly
Tip
Pull rearward to remove and connect the electrical connector and push lamp inward in order to position the lamp to the body panel.
4
Rear Lamp Harness Connector
Ensure to connect the lamp harness connector before securing the lamp to the rear body panel.

Jul 29, 2011 | Chevrolet Impala Cars & Trucks

2 Answers

Have no users manual and i'm not sure how you would replace the light bulb on the brake light


Change the Rear Brake Lights
  • Open the trunk and twist the retaining wing nuts off the studs holding the carpeted trim cover in place on the back side of the tail lamps.
  • Pull the carpeted trim cover out of the way and pry the plastic caps out of the holes with the screwdriver tip.
  • Unbolt the nuts holding the tail-lamp assembly in place using the socket set.
  • Pull the tail lamp assembly away from the body of the Stratus. Grab the socket for the bulb in question and twist it counterclockwise to remove it. Pull the old bulb out by hand and insert the replacement bulb. Reinstall the socket in reverse of removal.
  • Push the tail lamp assembly back into position and tighten the nuts back down onto the retaining studs using the socket set. Pop the plastic caps back into the holes, pull the carpeted trim cover back into position and reinstall the plastic wing nuts. Close the trunk.

Jul 21, 2011 | 2006 Dodge Stratus

1 Answer

Replacing rear brake light bulb


Carefully remove the two trim plugs from each tail light assembly with a small knife blade. Remove the two hex head bolts on each assembly. Insert a small paint stir stick (soft wood won't damage paint) between the fender and the tail light assembly. Gently pull the opposite (inside) side of the assembly off. The paint stick allow the assembly to pop off the ball and socket pin holding the outside part of the assembly in place. Unplug the power plug by releasing the retainer clip. Unscrew the large black plastic nuts on the back of the assembly with a very large screwdriver, if they can't be turned by hand,and remove. Replace burned out bulb/s and reassemble in reverse order. Remember the trim plugs have two prongs on them. Position them with the prongs and the direct top and bottom and press into place.

Apr 09, 2011 | 2004 Porsche Cayenne

1 Answer

How do I replace 2004 Pontiac Vibe passenger side tail light assembly?


Hello Tim.

Here is the procedure.
  1. Open the rear compartment lid.
  2. Remove the rear compartment trim panel (4).
  3. Remove the tail lamp socket (2) from the tail lamp(7).
  4. Remove the tail lampbulb (1) from the lamp socket (2).
kiltylake_125.gif


There you are, Happy New year.

KL

Jan 01, 2011 | 2004 Pontiac Vibe

3 Answers

Tail lights do not work on a 2000 lexus rx 300 bulbs are fine, all other lights work fine


You may have a fried fuse. Look in your owners manual to find out which fuse it is in the fuse box diagram. If that is the problem make sure to use the same amperage fuse to replace the burned one with. I fried fuse is usually a sign that you have a short somewhere. But they can also fry for other reasons such as excess moisture somewhere. Sometimes they just burn from age and fatigue. It may solve it to just replace the fuse, but if there really is a short, the new fuse will fry too.

Dec 29, 2010 | 2000 Lexus RX 300

1 Answer

What do I need to unscrew in the trunk to change the reverse light in my 01 chevy impala


Tail Lamp Assembly Removal & Installation To Remove:
  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.
  8. Remove the side marker lamp socket by turning counterclockwise.
To Install:
  1. Install the side marker lamp socket by turning clockwise.
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
prev.gif next.gif

Oct 18, 2010 | 2001 Chevrolet Impala

1 Answer

How do you replace a rear brake light on a 2003 durango


Take the trim off that covers the tail light assembly and then remove the bolts that hold it in.Once the tail light assembly is in your hand then unplug the lamp,turn the bulb to the right until it unlocks then pull it out,reverse all to assemble.Merry Christmas and good luck!

Dec 24, 2009 | 2003 Dodge Durango

2 Answers

Left rear turn signal bulb is burned out.


Tail Lamp Assembly
Removal & Installation
To Remove:

  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.

  1. To Install:
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
      Please don't forget to rate !!!!!!

    Mar 28, 2009 | 2002 Buick Century

    1 Answer

    Replacing rear turn signal bulb in 2003 Mustang


    remove the trim panel at the very rear of trunk, remove it and place it out of the way, remove tail light Assembly retaining nuts top and bottom, I think there are 6 per side, pull the tail light assembly straight back to access the bulbs for replacement.

    Dec 04, 2008 | 2003 Ford Mustang

    Not finding what you are looking for?
    2004 Mazda 6 Hatchback Logo

    61 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    yadayada
    yadayada

    Level 3 Expert

    74896 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7689 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...