Question about Cars & Trucks

1 Answer

How do i remove a/c control buttons from dashboard

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,249 Answers

Carefully pull hard.

Posted on Dec 15, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I clean coffee from climate directional buttons?


i would recommend you remove the unit. Two of the control knobs are removable the rest must be accessed by removing the unit then the front panel of the unit SubaruWRX image

May 11, 2015 | 1997 Subaru Outback

1 Answer

Replace engine control module 1993 gm sonoma


Why would you have to remove the dashboard.

The Module can be accessed from under the dash on the passenger side.


25350800-kiyu5aqkqelb2o03f4kwguli-3-0.gif

Jan 02, 2015 | 1993 GMC Sonoma Club

1 Answer

How do i remove the dashboard on a 2003 kia sorento


I can't tell you specifically for your vehicle but they hide them all the same. You will have to remove more than just your "dash". You will have to remove any knobs or control buttons. Sometimes there are mounting screws behind them. The ashtray has a couple of screws and there are all sorts of concealing caps that will need to be gently pried off to expose hex screw heads. Sorry I can't be more helpful but without a diagram it is a hunt/peck and pull to find the fastening point. (take pictures)

Jan 27, 2014 | Kia Sorento LX Cars & Trucks

1 Answer

Why is the rear vents blowing cold and the front vents have no air coming out on a 2003 ford explorer


Look in the front dashboard. You should have vent controls (2-3 buttons).. Press a couple while your air is running... If it doesn't blow air, your vent hose might have been removed or are clogged

May 14, 2013 | Cars & Trucks

1 Answer

Looking for where the heater cord is located?


To remove and installing the Heater Core, check this procedure...
  1. Disconnect and plug the heater hoses at the firewall.
  2. Disconnect the heater valve control cable.
  3. Remove the heater unit attaching nut on the firewall.
  4. Remove the dashboard as follows:
    1. Remove the center panel.
    2. Disconnect the wire connectors at the fuse box.
    3. Disconnect the sunroof switch connector, if equipped.
    4. Disconnect the ground cable at the right of the steering column and the power mirror switch wire connector.
    5. Remove the side air vent knob and face plate.
    6. Remove the screws attaching the air vent control lever.
    7. Remove the center panel, radio and heater control head.
    8. Remove the gauge upper panel (4-door) or instrument panel (3-door).
    9. Disconnect the speedometer cable.
    10. Remove the center upper lid.
    11. Remove the side defroster garnishes on both ends of the dash.
    12. Lower the steering column.
    13. Remove the dashboard mounting bolts.
    14. Lift and remove the dashboard assembly.
1. Remove the heater duct.

zjlimited_113.jpg

Fig. 1: Removing the heater duct assembly

  1. Remove the steering column bracket and duct assembly.
  2. Remove the heater assembly mounting bolts.
  3. Remove the heater assembly and remove the heater core.
zjlimited_114.jpg

Fig. 2: Removing the heater case assembly

zjlimited_115.jpg

Fig. 3: Removing the heater core from the heater case


Hope this helps (remember to rate this answer).

Nov 23, 2010 | 1992 Honda Civic

2 Answers

How to use cruies controw on a 1997 isuzu rodeo


First-on dashboard right hand side of steering wheel there are large (approx 1" sq) buttons-push to turn on-push again to turn off-for the rearwindow defroster,hazard flashing lights and....cruise control. Push cruise button to "on" and you'll see green lights on speedometer bezel light up. On end of wiper control stick on rightside of steering wheel-you'll find a pushbutton. Get car to speed you want-then push this button in. To turn off cruise control completely-push first button you pushed on dashboard.

Mar 21, 2010 | 1997 Isuzu Rodeo

3 Answers

2004 Saturn Vue hazard light button pushed into the dash


Same on my 2004 Vue. Pry up shift panel, use putty knifes, slot screew driver, then pry up outer panel (with power window switches). remove screws holding radio, climate control panel (I believe there were 4 screws). gently lift this panel up and push gently toward windshield to unlatch. Don't lift higher than is necessary to acess 4 way flasher switch as climate control cables shouldn't be pulled hard so as do damage to climate control panel. The catches broke on my 4 way switch so I used Goop (from Walmart, Lowes etc.) to glue it in switch recptical. After glue dries, latch panel, screw panel in place and snap widow switch and shif panels in place.

Jul 11, 2009 | 2004 Saturn VUE

2 Answers

How to replace bulbs for ac/ heater control unit


1. Remove the dash around radio (just clips)
2. Remove 2 screws pointing up . (You do not need to remove screws which are parallel to the floor)
3. Remove screw pointing up on the bottom of the dashboard on left side of the driver (near left leg).
4. Remove 2 screws pointing up in the instrument cluster area.
5. Put car in 1st gear and gently remove black plastic surrounding instruments (it will have ait vents, so slide it carefully out not to damage foam insulation on air ducts; start on the bottom hear steering column) ; unplug connectors to clock and emergency flashers.
6. Remove 2 screws, now exposed, near instrument area, holding dashboard. (that was what I spent most time on, I didn't know about this screws.
7. Now gently remove (or move up) dashboard (around instrument cluster and heating controls.) Start next to ignition (careful not to damage the bulb next to the ignition.
Since you only need to get to the heating controls block, I only move up the dashboard next to it.
8. Remove 2 screws that hold the heating control and slide heating control out . This step is unnecessary If you totally removed the dashboard.
9. Pull out lever controls for fan speed, zone and temp
10. Use the screwdriver (flat) to pry 2 plastic tabs on top and on the bottom of heating control so black cover can be remover.
11. You did it! two bulbs are going to be under the cover.

May 19, 2009 | 2001 Toyota Sienna

1 Answer

Remove a 93 Golf 3 VR6 Dashboard


  1. 5b63f60.jpge173e8a.jpg
  2. On Cabriolet with an air bag, disconnect the negative battery cable and wait at least 20 minutes for the back-up power supply to discharge. Make sure no one is in the vehicle when connecting the battery. Unintended deployment of the air bag can cause serious or fatal injury.
  3. Disconnect the negative battery cable.
  4. Remove the gear shift knob and boot and remove the center console.
  5. Remove the steering wheel.
  6. Remove the knee bar from below the dashboard.
  7. Remove the steering column support bracket and lower the column.
  8. Pull the knobs off the heater controls and remove the control assembly and the radio.
  9. Remove the headlight switch and switch blanks to gain access to the screws. Remove the instrument cluster and trim panel around the cluster.
  10. Remove the glove compartment.
  11. At the firewall, remove the plastic tray and remove the 2 nuts holding the top of the dashboard.
  12. .Remove the main fuse panel and disconnect the plugs at the back. Disconnect the ground wires.
  13. Disconnect any remaining wiring from the dashboard and remove the 4 last screws; 1 at each end and 1 at each end of the instrument cluster area. Remove the dashboard.
To install:
  1. Fit the dashboard into place and start all 4 screws, then tighten them.
  2. Install the fuse panel and connect the wiring.
  3. Secure the steering column into place.
  4. Install the switches and instrument cluster.
  5. Install the heater controls and radio.
  6. Install the console and connect all wiring.
  7. Connect the battery to test the electrical system.
  8. Install the steering wheel, knee bar and all remaining components.
Good luck...

Sep 26, 2008 | Volkswagen Jetta Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...